SLVSF24C december   2020  – may 2023 TPS272C45

PRODUCTION DATA  

1.   1
2. 1 Features
3. 2 Applications
4. 3 Description
5. 4 Revision History
6. 5 Device Comparison Table
7. 6 Pin Configuration and Functions
   1. 6.1 Recommended Connections for Unused Pins
8. 7 Specifications
   1. 7.1 Absolute Maximum Ratings
   2. 7.2 ESD Ratings
   3. 7.3 Recommended Operating Conditions
   4. 7.4 Thermal Information
   5. 7.5 Electrical Characteristics
   6. 7.6 SNS Timing Characteristics
   7. 7.7 Switching Characteristics
   8. 7.8 Typical Characteristics
9. 8 Parameter Measurement Information
10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
       1. 9.3.1 Programmable Current Limit
          1. 9.3.1.1 Inrush Current Handling
          2. 9.3.1.2 Calculating RILIMx
          3. 9.3.1.3 Configuring ILIMx From an MCU
       2. 9.3.2 Low Power Dissipation
       3. 9.3.3 Protection Mechanisms
          1. 9.3.3.1 Short-Circuit Protection
             1. 9.3.3.1.1 VS During Short-to-Ground
          2. 9.3.3.2 Inductive Load Demagnetization
          3. 9.3.3.3 Thermal Shutdown
          4. 9.3.3.4 Undervoltage Lockout on VS (UVLO)
          5. 9.3.3.5 Undervoltage Lockout on Low Voltage Supply (VDD_UVLO)
          6. 9.3.3.6 Power-Up and Power-Down Behavior
          7. 9.3.3.7 Overvoltage Protection (OVPR)
       4. 9.3.4 Diagnostic Mechanisms
          1. 9.3.4.1 Current Sense
             1. 9.3.4.1.1 RSNS Value
                1. 9.3.4.1.1.1 Current Sense Output Filter
          2. 9.3.4.2 Fault Indication
             1. 9.3.4.2.1 Fault Event Diagrams
          3. 9.3.4.3 Short-to-Supply or Open-Load Detection
             1. 9.3.4.3.1 Detection With Switch Enabled
             2. 9.3.4.3.2 Detection With Switch Disabled
          4. 9.3.4.4 Current Sense Resistor Sharing
    4. 9.4 Device Functional Modes
       1. 9.4.1 Off
       2. 9.4.2 Diagnostic
       3. 9.4.3 Active
       4. 9.4.4 Fault
11. 10Application and Implementation
    1. 10.1 Application Information
       1. 10.1.1 IEC 61000-4-5 Surge
       2. 10.1.2 Inverse Current
       3. 10.1.3 Loss of GND
       4. 10.1.4 Paralleling Channels
       5. 10.1.5 Thermal Information
    2. 10.2 Typical Application
       1. 10.2.1 Design Requirements
       2. 10.2.2 Detailed Design Procedure
          1. 10.2.2.1 RILIM Calculation
          2. 10.2.2.2 Diagnostics
             1. 10.2.2.2.1 Selecting the RISNS Value
       3. 10.2.3 Application Curves
    3. 10.3 Power Supply Recommendations
    4. 10.4 Layout
       1. 10.4.1 Layout Guidelines
       2. 10.4.2 Layout Example
12. 11Device and Documentation Support
    1. 11.1 Documentation Support
       1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
13. 12Mechanical, Packaging, and Orderable Information

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 

Copyright © 2023, Texas Instruments Incorporated