SLVSMB0 June   2026

 

  1.   1
  2.   Description
  3.   Features
  4.   4
  5. 1 Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Kit Contents
    3. 1.3 Specifications
    4. 1.4 Device Information
  6. 2 Hardware
    1. 2.1 Hardware Requirements
    2. 2.2 Connecting the BQ27Z855 Circuit Module to a Battery Pack
    3. 2.3 EVM Jumpers and Terminal Block Description
  7. 3 Software
    1. 3.1 System Requirements
    2. 3.2 Software Installation
    3. 3.3 Updating Firmware
    4. 3.4 Troubleshooting Unexpected Dialog Boxes
  8. 4 Using bqStudio
    1. 4.1 Starting the Program
    2. 4.2 Setting Programmable BQ27Z855 Options
    3. 4.3 Configuring the Integrated Linear Battery Charger
  9. 5 Calibrating Gauge Measurements
    1. 5.1 Voltage Calibration
    2. 5.2 Current Calibration
  10. 6 Chemical ID
    1. 6.1 Chemical ID Selection Process
    2. 6.2 Hardware Requirements and Setup
    3. 6.3 Logging Data in bqStudio
    4. 6.4 GPCChem Tool
    5. 6.5 Programming a Chemical ID
    6. 6.6 Further Resources for Chemical ID Process
  11. 7 Learning Cycle and Golden Image
    1. 7.1 Learning Cycle Process Description
    2. 7.2 Data Memory Configuration
    3. 7.3 Learning Cycle Steps
    4. 7.4 Low Temperature Optimization
    5. 7.5 Creating the Golden Image File
    6. 7.6 Programming the Golden Image File
  12. 8 Gauge Communication
    1. 8.1 Advanced Communication in bqStudio
    2. 8.2 Standard Data Commands
    3. 8.3 Manufacturer Access Commands
    4. 8.4 Further Resources on Gauge Communication
  13. 9 BQ27Z855-Based Circuit Module
    1. 9.1 Circuit Module Connections
    2. 9.2 Pin Descriptions
  14. 10Hardware Design Files
    1. 10.1 Schematic
    2. 10.2 Bill of Materials (BOM)
    3. 10.3 PCB Layouts
  15. 11Additional Information
    1.     Trademarks

Bill of Materials (BOM)

Table 10-1 Bill of Materials
Fitted Description Designator PartNumber Quantity Manufacturer PackageReference Value Alternate Manufacturer Alternate PartNumber
Fitted Printed Circuit Board !PCB1 BMS108 1 Any
Fitted Test Point, Orange, 1-Pin THD, RoHS BAT, CHG, CP, CP_BOOT, DSG, ENAB, INT, PACK, REG18, SCL, SDA, SRN1, SRP1, TS 5003 14 5003
Fitted Test Point, Miniature, Black, TH BAT-, GND1, GND2, GND3, PACK-, PGND1, PGND2 5001 7 Keystone Black Miniature Testpoint
Fitted Test Point, Miniature, Green, TH BAT+ 5116 1 Keystone Green Miniature Testpoint
Fitted CAP, CERM, 0.1 uF, 25 V, +/- 10%, X5R, 0201 C1, C2, C3, C4 GRM033R61E104KE14J 4 MuRata 0201 0.1uF
Fitted CAP, CERM, 0.1 uF, 16 V,+/- 10%, X7R, 0201 C5 GRM033Z71C104KE14D 1 MuRata 0201 0.1uF
Fitted CAP, CERM, 1 uF, 16 V, +/- 10%, X7R, 0603 C6, C7 EMK107B7105KA-T 2 Taiyo Yuden 0603 1uF
Fitted CAP, CERM, 0.01 uF, 10 V, +/- 10%, X5R, 0201 C8 GRM033R61A103KA01D 1 MuRata 0201 0.01uF
Fitted CAP, CERM, 1.5 uF, 16 V, +/- 10%, X7R, 0805 C9 C0805C155K4RACTU 1 Kemet 0805 1.5uF
Fitted CAP, CERM, 2200 pF, 16 V, +/- 10%, X7R, 0201 C10 GRM033R71C222KA88D 1 MuRata 0201 2200pF
Fitted Fiducial mark. There is nothing to buy or mount. FID1, FID2, FID3 N/A 3 N/A N/A
Fitted Terminal Block, 5mm, 2x1, R/A, TH J1, J3, J4 1792863 3 Phoenix Contact Terminal Block, 5mm, 2x1, R/A, TH
Fitted Terminal Block, 5mm, 4x1, R/A, TH J2 1792889 1 Phoenix Contact Terminal Block, 5mm, 4x1, R/A, TH
Fitted Header, 2.54mm, 4x1, R/A, Tin, TH J5 640455-4 1 TE Connectivity Header, 2.54mm, 4x1, R/A, TH
Fitted Header, 2.54 mm, 2x1, Gold, TH J6 GBC02SAAN 1 Sullins Connector Solutions Header, 2.54 mm, 2x1, TH
Fitted Thermal Transfer Printable Labels, 0.650" W x 0.200" H - 10,000 per roll LBL1 THT-14-423-10 1 Brady PCB Label 0.650 x 0.200 inch
Fitted Test Point, Miniature, Red, TH PACK+ 5000 1 Keystone Red Miniature Testpoint
Fitted Transistor MOSFET Array Dual N-CH 20V 14.5A 6-Pin uDFN2030 T/R Q1 DMN2008LFU-7 1 Diodes Inc. U-DFN2030-6
Fitted Res Thick Film 0201 1K Ohm 1% 1/20W ±200ppm/°C Molded SMD SMD Paper T/R R1, R6 CRCW02011K00FNED 2 Vishay Dale 0201
Fitted 10 mOhms ±1% 1W Chip Resistor 1206 (3216 Metric) Current Sense, Moisture Resistant Metal Element R2 CSNL1206FT10L0 1 Stackpole Electronics 1206 10m
Fitted RES, 0, 5%, 0.05 W, 0201 R3, R4, R11, R12 CRCW02010000Z0ED 4 Vishay-Dale 0201 0
Fitted 0 Ohms Jumper 0.1W, 1/10W, 5.8A Chip Resistor 0201 (0603 Metric) Automotive AEC-Q200 Metal Foil R5 HCJ0201ZT0R00 1 Stackpole Electronics 0201 0
Fitted RES SMD 100 OHM 1% 1/20W 0201, ERJ-1GNF1000C R7, R8, R9 ERJ1GNF1000C 3 Panasonic Electronic Components 0201 100Ω
Fitted RES Thick Film, 50kΩ, 1%, 0.063W, 100ppm/°C, 0402 R10 CRCW040250K0FKED 1 Vishay 0402
Fitted Switch, SPST-NO, Off-Mom, 0.02 A, 15 VDC, SMD S1, S2 EVQ-PLHA15 2 Panasonic 4.9x4.9mm
Fitted Shunt, 100mil, Gold plated, Black SH-J1 SNT-100-BK-G 1 Samtec Shunt 1x2 3M 969102-0000-DA
Fitted Single-Channel ESD in 0402 Package With 10pF Capacitance and 6V Breakdown, DPY0002A (X1SON-2) U1, U3, U4, U5 TPD1E10B06DPYR 4 Texas Instruments DPY0002A Texas Instruments TPD1E10B06DPYT
Fitted BQ27Z855YAHR U2 BQ27Z855YAHR 1 Texas Instruments DSBGA15
Fitted Thermistor NTC, 10.0k ohm, 1%, Disc, 5x8.4 mm, Fitted in T6 header RT1 103AT-2 1 SEMITEC Corporation Disc, 5x8.4 mm 10k