SNVSD07 October 2025 LM251772-Q1
PRODUCTION DATA
Table 9-1 lists the memory-mapped registers for the LM251772 registers. All register offset addresses not listed in Table 9-1 must be considered as reserved locations and the register contents must not be modified.
| Offset | Acronym | Register Name | Section |
|---|---|---|---|
| 3h | CLEAR_FAULTS | CLEAR_FAULTS | Section 9.1 |
| Ah | ILIM_THRESHOLD | ILIM_THRESHOLD | Section 9.2 |
| Ch | VOUT_TARGET1_LSB | VOUT_TARGET1_LSB | Section 9.3 |
| Dh | VOUT_TARGET1_MSB | VOUT_TARGET1_MSB | Section 9.4 |
| 21h | USB_PD_STATUS_0 | USB_PD_STATUS_0 | Section 9.5 |
| 78h | STATUS_BYTE | STATUS_BYTE | Section 9.6 |
| 81h | USB_PD_CONTROL_0 | USB_PD_CONTROL_0 | Section 9.7 |
| D0h | MFR_SPECIFIC_D0 | MFR_SPECIFIC_D0 | Section 9.8 |
| D1h | MFR_SPECIFIC_D1 | MFR_SPECIFIC_D1 | Section 9.9 |
| D2h | MFR_SPECIFIC_D2 | MFR_SPECIFIC_D2 | Section 9.10 |
| D5h | MFR_SPECIFIC_D5 | MFR_SPECIFIC_D5 | Section 9.11 |
| D6h | MFR_SPECIFIC_D6 | MFR_SPECIFIC_D6 | Section 9.12 |
| D7h | MFR_SPECIFIC_D7 | MFR_SPECIFIC_D7 | Section 9.13 |
| D8h | MFR_SPECIFIC_D8 | MFR_SPECIFIC_D8 | Section 9.14 |
| DAh | IVP_VOLTAGE | IVP_VOLTAGE | Section 9.15 |
Complex bit access types are encoded to fit into small table cells. Table 9-2 shows the codes that are used for access types in this section.
| Access Type | Code | Description |
|---|---|---|
| Read Type | ||
| R | R | Read |
| Write Type | ||
| W | W | Write |
| Reset or Default Value | ||
| -n | Value after reset or the default value | |
CLEAR_FAULTS is shown in Table 9-3.
Return to the Summary Table.
clear all latched status flags
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-0 | CLEAR_FAULTS | R | 0h | Accessing the address is enough to clear fault |
ILIM_THRESHOLD is shown in Table 9-4.
Return to the Summary Table.
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-0 | ILIM_THRESHOLD | R/W | 12h | ISNS current limit threshold voltage.
Value in bracket considers a 10mOhms sens resistor
|
VOUT_TARGET1_LSB is shown in Table 9-5.
Return to the Summary Table.
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-0 | VOUT_A | R/W | FFh | Output target Voltage Logical Register Vout Setting Lower Limit: 3.3V or 1V depending on SEL__FB_DIV20 Upper Limit: 48V or 24V depending on SEL__FB_DIV20 Step size: 20mV or 10mV depending on SEL__FB_DIV20 Value Calculation for 20mV Equation 3 Value Calculation for 10mV Equation 2 |
VOUT_TARGET1_MSB is shown in Table 9-6.
Return to the Summary Table.
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-4 | NIL | R | 0h | This bit is not implemented in hardware. During write operations data for this bit is ignored. During read operations 0 is returned. |
| 3-0 | VOUT_A | R/W | 0h | Output target Voltage Logical Register Vout Setting Lower Limit: 3.3V or 1V depending on SEL__FB_DIV20 Upper Limit: 48V or 24V depending on SEL__FB_DIV20 Step size: 20mV or 10mV depending on SEL__FB_DIV20 Value Calculation for 20mV Equation 3 Value Calculation for 10mV Equation 2 |
USB_PD_STATUS_0 is shown in Table 9-7.
Return to the Summary Table.
USB-PD STATUS REGISTER
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | NIL | R | 0h | This bit is not implemented in hardware. During write operations data for this bit is ignored. During read operations 0 is returned. |
| 6 | CC_OPERATION | R | 0h | Instantaneous status for constant current (CC) ILIM operation |
| 5-0 | NIL | R | 0h | This bit is not implemented in hardware. During write operations data for this bit is ignored. During read operations 0 is returned. |
STATUS_BYTE is shown in Table 9-8.
Return to the Summary Table.
FAULT STATUS LOW BYTE
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | BUSY | R | 0h | unit is busy
|
| 6 | OFF | R | 0h | device not providing VOUT and/or unit is
off
|
| 5 | VOUT | R | 0h | VOUT_OV fault
|
| 4 | IOUT | R | 0h | IOUT_OC fault
|
| 3 | INPUT | R | 0h | VIN_UV fault
|
| 2 | TEMPERATURE | R | 0h | Temperature fault or warning
|
| 1 | CML | R | 0h | Comm, Logic, Memory event
|
| 0 | OTHER | R | 0h | other fault or warning
|
USB_PD_CONTROL_0 is shown in Table 9-9.
Return to the Summary Table.
USB-PD CONTROL REGISTER
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-2 | NIL | R | 0h | This bit is not implemented in hardware. During write operations data for this bit is ignored. During read operations 0 is returned. |
| 1 | FORCE_DISCH | R/W | 0h | Activates Vo discharge
|
| 0 | CONV_EN2 | R/W | 0h | Enables the power stage
|
MFR_SPECIFIC_D0 is shown in Table 9-10.
Return to the Summary Table.
CONFIG_0 Device Configuration Register 0
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | NIL | R | 0h | This bit is not implemented in hardware. During write operations data for this bit is ignored. During read operations 0 is returned. |
| 6 | EN_NEG_CL_LIMIT | R/W | 0h | Enables ILIM for negative current limit,
If disabled ILIM clamps pos I_L
|
| 5 | EN_VCC1 | R/W | 1h | Enables the VCC1 auxiliary LDO
|
| 4 | IMON_LIMITER_EN | R/W | 1h | Enables the Imon in limiter
configuration
|
| 3 | HICCUP_EN | R/W | 0h | Enables Hiccup short circuit
|
| 2 | DRSS_EN | R/W | 0h | Enables Dual Spread Spectrum
|
| 1 | USLEEP_EN | R/W | 1h | Enables micro sleep mode
|
| 0 | CONV_EN | R/W | 0h | Enables the power stage
|
MFR_SPECIFIC_D1 is shown in Table 9-11.
Return to the Summary Table.
CONFIG_1 Device Configuration Register 1
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | EN_THER_WARN | R/W | 0h | Enables Thermal Warning
|
| 6-5 | THW_THRESHOLD | R/W | 0h | Selects the Thermal Warning Threshold
|
| 4 | EN_NINT | R/W | 1h | Configures the nFLT pin handler to act
as interrupt pin or nFLT pin
|
| 3 | EN_DTRK_STARTOVER | R/W | 1h | Enables a direct start-up if DTRK is
enabled without waiting for the DTRK PWM signal
|
| 2 | FORCE_BIASPIN | R/W | 0h | Enables the priority to supply VCC2 from
BIAS by lowering the threshold.
|
| 1 | EN_BB_2P_FPWM | R/W | 0h | Enables 2phase BB switching in fPWM mode
|
| 0 | EN_BB_2P_PSM | R/W | 1h | Enables 2phase BB switching in PSM mode
|
MFR_SPECIFIC_D2 is shown in Table 9-12.
Return to the Summary Table.
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | NIL | R | 0h | This bit is not implemented in hardware. During write operations data for this bit is ignored. During read operations 0 is returned. |
| 6 | EN_ACTIVE_DVS | R/W | 1h | Enables the active down ramp for DVS
using the discharge
|
| 5-4 | DVS_SLEW_RAMP | R/W | 3h | Sets the positive and negative Vo slew
rate for DVS
|
| 3-2 | DISCHARGE_STRENGTH | R/W | 2h | Sets the discharge current for the Vo
discharge
|
| 1 | DISCHARGE_CONFIG0 | R/W | 1h | Selects the discharge together with
CONV_EN
|
| 0 | DISCHARGE_CONFIG1 | R/W | 0h | Selects the discharge until the VTH
DISCH
|
MFR_SPECIFIC_D5 is shown in Table 9-13.
Return to the Summary Table.
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | NIL | R | 0h | This bit is not implemented in hardware. During write operations data for this bit is ignored. During read operations 0 is returned. |
| 5-0 | V_OVP2 | R/W | 3Fh | OVP2 threshold voltage
|
MFR_SPECIFIC_D6 is shown in Table 9-14.
Return to the Summary Table.
PS_Config0 Power stage Configuration
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | CONFIG_SYNC_PIN | R/W | 0h | Selects the SYNC function to maintain
parallel operation
|
| 5 | EN_CONST_TDEAD | R/W | 0h | Forces a constant deadtime for the
setting of SEL_MIN_DEADTIME_GDRV. Disables frequency
dependency of min Tdead
|
| 4 | SEL_SCALE_DT | R/W | 1h | Scales the gate driver dead time freq
dependence and 2MHz setpoint
|
| 3-2 | SEL_MIN_DEADTIME_GDRV | R/W | 1h | Defines the minimum dead time at fsw =
2Mhz for the gate driver
|
| 1-0 | BB_MIN_TIME_OFFSET | R/W | 1h | Scales the BB min Ton or Toff time for
the gate refresh
|
MFR_SPECIFIC_D7 is shown in Table 9-15.
Return to the Summary Table.
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | NIL | R | 0h | This bit is not implemented in hardware. During write operations data for this bit is ignored. During read operations 0 is returned. |
| 5-4 | SEL_INDUC_DERATE | R/W | 2h | Select the inductor de-rating for PSM
mode to slope
|
| 3-0 | SEL_SLOPE_COMP | R/W | 8h | Select slope comp current, as ratio of
RT current
|
MFR_SPECIFIC_D8 is shown in Table 9-16.
Return to the Summary Table.
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | SEL_FB_DIV20 | R/W | 1h | Select internal FB divider ratio of 20
|
| 6 | EN_CDC | R/W | 0h | Enables the cable drop compensation
|
| 5-4 | CDC_GAIN | R/W | 0h | Selects the Gain for the CDC voltage
(1V) with respect to Vout
|
| 3-2 | SEL_DRV1_SEQ | R/W | 1h | Select the sequencing for the DRV 1
operation
|
| 1-0 | SEL_DRV1_SUP | R/W | 0h | Select the driver configuration for DRV1
pin
|
IVP_VOLTAGE is shown in Table 9-17.
Return to the Summary Table.
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-0 | V_IVP | R/W | FFh | Input Overvoltage Protection and
Regulation Threshold
|