SPRUJ26A September   2021  – April 2024

1.   1
2.   Abstract
3.   Trademarks
4. 1Introduction
5. 2Motor Control Theory
   1. 2.1 Mathematical Model and FOC Structure of PMSM
   2. 2.2 Field Oriented Control of PM Synchronous Motor
   3. 2.3 Sensorless Control of PM Synchronous Motor
      1. 2.3.1 Enhanced Sliding Mode Observer with Phase Locked Loop
         1. 2.3.1.1 Design of ESMO for PMSM
         2. 2.3.1.2 Rotor Position and Speed Estimation With PLL
   4. 2.4 Hardware Prerequisites for Motor Drive
      1. 2.4.1 Motor Phase Voltage Feedback
   5. 2.5 Additional Control Features
      1. 2.5.1 Field Weakening (FW) and Maximum Torque Per Ampere (MTPA) Control
      2. 2.5.2 Flying Start
6. 3Running the Universal Lab on TI Hardware Kits
   1. 3.1 Supported TI Motor Evaluation Kits
   2. 3.2 Hardware Board Setup
      1. 3.2.1  LAUNCHXL-F280025C Setup
      2. 3.2.2  LAUNCHXL-F280039C Setup
      3. 3.2.3  LAUNCHXL-F2800137 Setup
      4. 3.2.4  TMDSCNCD280025C Setup
      5. 3.2.5  TMDSCNCD280039C Setup
      6. 3.2.6  TMDSCNCD2800137 Setup
      7. 3.2.7  TMDSADAP180TO100 Setup
      8. 3.2.8  DRV8329AEVM Setup
      9. 3.2.9  BOOSTXL-DRV8323RH Setup
      10. 3.2.10 BOOSTXL-DRV8323RS Setup
      11. 3.2.11 DRV8353RS-EVM Setup
      12. 3.2.12 BOOSTXL-3PHGANINV Setup
      13. 3.2.13 DRV8316REVM Setup
      14. 3.2.14 TMDSHVMTRINSPIN Setup
      15.      34
      16.      35
   3. 3.3 Lab Software Implementation
      1. 3.3.1 Importing and Configuring Project
      2.      38
      3.      39
      4. 3.3.2 Lab Project Structure
      5. 3.3.3 Lab Software Overview
   4. 3.4 Monitoring Feedback or Control Variables
      1. 3.4.1 Using DATALOG Function
      2. 3.4.2 Using PWMDAC Function
      3. 3.4.3 Using External DAC Board
   5. 3.5 Running the Project Incrementally Using Different Build Levels
      1. 3.5.1 Level 1 Incremental Build
         1. 3.5.1.1 Build and Load Project
         2. 3.5.1.2 Setup Debug Environment Windows
         3. 3.5.1.3 Run the Code
      2. 3.5.2 Level 2 Incremental Build
         1. 3.5.2.1 Build and Load Project
         2. 3.5.2.2 Setup Debug Environment Windows
         3. 3.5.2.3 Run the Code
      3. 3.5.3 Level 3 Incremental Build
         1. 3.5.3.1 Build and Load Project
         2. 3.5.3.2 Setup Debug Environment Windows
         3. 3.5.3.3 Run the Code
      4. 3.5.4 Level 4 Incremental Build
         1. 3.5.4.1 Build and Load Project
         2. 3.5.4.2 Setup Debug Environment Windows
         3. 3.5.4.3 Run the Code
7. 4Building a Custom Board
   1. 4.1 Building a New Custom Board
      1. 4.1.1 Hardware Setup
      2. 4.1.2 Migrating Reference Code to a Custom Board
         1. 4.1.2.1 Setting Hardware Board Parameters
         2. 4.1.2.2 Modifying Motor Control Parameters
         3. 4.1.2.3 Changing Pin Assignment
         4. 4.1.2.4 Configuring the PWM Module
         5. 4.1.2.5 Configuring the ADC Module
         6. 4.1.2.6 Configuring the CMPSS Module
         7. 4.1.2.7 Configuring Fault Protection Function
      3. 4.1.3 Adding Additional Functionality to Motor Control Project
         1. 4.1.3.1 Adding Push Buttons Functionality
         2. 4.1.3.2 Adding Potentiometer Read Functionality
         3. 4.1.3.3 Adding CAN Functionality
   2. 4.2 Supporting New BLDC Motor Driver Board
   3. 4.3 Porting Reference Code to New C2000 MCU
8.   A Appendix A. Motor Control Parameters
9.   References
10.   Revision History

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 

Copyright © 2024, Texas Instruments Incorporated