SN54LVTH646

現行

具有 3 態輸出的 3.3-V ABT 八路匯流排收發器和暫存器

立即訂購

產品規格表

document-pdfAcrobat SN54LVTH646, SN74LVTH646 datasheet (Rev. H) (英文)

SN54LVTH646

現行

產品規格表

立即訂購

產品詳細資料

Number of channels

8

IOL (max) (mA)

48

IOH (max) (mA)

-48

Input type

TTL/CMOS

Output type

LVTTL

Features

Balanced outputs, Bus-hold, Over-voltage tolerant inputs, Partial power down (Ioff), Power up 3-state, Ultra high speed (tpd <5ns)

Technology family

LVT

Rating

Military

Operating temperature range (°C)

-55 to 125

Number of channels

8

IOL (max) (mA)

48

IOH (max) (mA)

-48

Input type

TTL/CMOS

Output type

LVTTL

Features

Balanced outputs, Bus-hold, Over-voltage tolerant inputs, Partial power down (Ioff), Power up 3-state, Ultra high speed (tpd <5ns)

Technology family

LVT

Rating

Military

Operating temperature range (°C)

-55 to 125

LCCC (FK)

28

130.6449 mm² (— mm × — mm)

Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V V_CC)
Support Unregulated Battery Operation Down to 2.7 V
Typical V_OLP (Output Ground Bounce)
<0.8 V at V_CC = 3.3 V, T_A = 25°C
I_off and Power-Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors
Latch-Up Performance Exceeds 500 mA Per JESD 17
ESD Protection Exceeds JESD 22
- 2000-V Human-Body Model (A114-A)
- 200-V Machine Model (A115-A)

Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V V_CC)
Support Unregulated Battery Operation Down to 2.7 V
Typical V_OLP (Output Ground Bounce)
<0.8 V at V_CC = 3.3 V, T_A = 25°C
I_off and Power-Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors
Latch-Up Performance Exceeds 500 mA Per JESD 17
ESD Protection Exceeds JESD 22
- 2000-V Human-Body Model (A114-A)
- 200-V Machine Model (A115-A)

These bus transceivers and registers are designed specifically for low-voltage (3.3-V) V_CC operation, but with the capability to provide a TTL interface to a 5-V system environment.

The ’LVTH646 devices consist of bus transceiver circuits, D-type flip-flops, and control circuitry arranged for multiplexed transmission of data directly from the input bus or from the internal registers. Data on the A or B bus is clocked into the registers on the low-to-high transition of the appropriate clock (CLKAB or CLKBA) input. Figure 1 illustrates the four fundamental bus-management functions that can be performed with the ’LVTH646.

Output-enable (OE\) and direction-control (DIR) inputs are provided to control the transceiver functions. In the transceiver mode, data present at the high-impedance port can be stored in either register or in both.

The select-control (SAB and SBA) inputs can multiplex stored and real-time (transparent mode) data. The direction control (DIR) determines which bus receives data when OE\ is low. In the isolation mode (OE\ high), A data can be stored in one register and/or B data can be stored in the other register.

When an output function is disabled, the input function still is enabled and can be used to store and transmit data. Only one of the two buses, A or B, can be driven at a time.

Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended.

To ensure the high-impedance state during power up or power down, OE\ should be tied to V_CC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

These devices are fully specified for hot-insertion applications using I_off and power-up 3-state. The I_off circuitry disables the outputs, preventing damaging current backflow through the devices when they are powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict.