TIDA-00012
고효율 절연 CAN 및 Profibus 인터페이스 레퍼런스 디자인
TIDA-00012
개요
The high-efficiency isolated CAN and Profibus interface reference design is intended for use in industrial systems that require isolated power for CAN and/or Profibus transceivers. This design highlights the ability to completely shut off both the power converter and data transceivers with just one GPIO signal from a microcontroller (when dropping into low-power modes, for example). This isolated interface delivers accurately regulated rails for both primary and secondary power to our Profibus and CAN transceivers without costly opto-coupler feedback circuits making this a simple, efficient and flexible isolated interface for industrial automation. This reference design has the additional feature of allowing the MCU to wait until power is good before transmitting data or to stop transmitting data if a power fault has occured on the interface.
The Tiva C Series Launch Pad form factor of this reference design allows easy connection to the LaunchPad board for use of the Tiva C microcontroller in handling the communications protocol to the interface.
특징
- Enable, soft-start and fault functions of TPS55010 provide full MCU control of the power supply rails to the communications interface to maximize system power savings
- Adjustable, high-switching frequency increases efficiency, decreases solution size and allows avoidance of sensitive frequency bands
- Galvanic insulation technology used in isolated Profibus and CAN transceivers provide proven reliability and stability over time, temperature and moisture
산업용
- 48-V servo drive
- AC input HVAC motor control
- AC 드라이브 유선 및 무선 통신
- AC 드라이브 유선 및 무선 통신
- AC 모터 제어 모듈
- AC 모터 제어 모듈
- AC-input closed loop stepper
- AC-input closed loop stepper
- Air Circuit Breaker (ACB)
- Analytical Lab Instrumentation
- DC 고속 충전소
- DC 고속 충전소
- DC 고속 충전소
- DC 고속 충전소
- DC 고속 충전소
- DC-fed Servo Power Stage
- DC-input closed loop stepper
- DC-input closed loop stepper
- Digital Input Module IEC61131-2
- Digital input module NAMUR
- Digital input module NAMUR
- EV 충전소 HMI 모듈
- EV 충전소 전원 모듈
- EV 충전소 전원 모듈
- Fieldbus 모듈
- HVAC 모터 제어
- High-speed digital input module
- High-speed digital input module
- IGBT-based Servo Power Stage
- IPM-based Servo Power Stage
- Isolated AC Drive Power Stage
- Linear motor segment controller
- Mixed module (AI,AO,DI,DO)
- Mixed module (AI,AO,DI,DO)
- Mobile robot safety module
- Motor Protection Relay and Contactors
- Multi-axis servo drive
- Non-Isolated AC Drive Power Stage
- Power conversion system (PCS)
- Servo drive ACDC rectifier with brake
- Servo drive active frontend
- Single phase wireless EV charging station
- Single phase wireless EV charging station
- Single phase wireless EV charging station
- Single phase wireless EV charging station
- Single phase wireless EV charging station
- Single-axis servo drive
- Telecom monitor unit
- Three phase wireless EV charging station
- Three phase wireless EV charging station
- Three phase wireless EV charging station
- Three phase wireless EV charging station
- UPS - 단상 라인 인터랙티브
- UPS - 단상 온라인
- 디지털 제어 텔레콤 정류기
- 로봇 안전 모듈
- 로봇 팔 카트
- 모바일 로봇 비전
- 모터 진단 및 모니터링
- 물류 로봇 모션 컨트롤러
- 배터리 셀 형성 및 테스트 장비
- 배터리 셀 형성 및 테스트 장비
- 산업용 로봇 비전
- 산업용 로봇 혼합 I/O 모듈
- 서보 드라이브 유선 및 무선 통신
- 서보 드라이브 유선 및 무선 통신
- 서보 드라이브 제어 모듈
- 서보 드라이브 제어 모듈
- 외과의사 콘솔
- 전자동 디지털 엔진 제어(FADEC)
- 전자동 디지털 엔진 제어(FADEC)
- 중앙 인버터
- 콕핏 디스플레이/HUD
- 프로세싱 및 비전 카트
- 휴머노이드 로봇 모터 드라이브
- 휴머노이드 로봇 센서 모듈
완조립 보드는 테스팅과 성능 검증을 위해서만 개발되었으며 판매를 위한 것이 아닙니다.
설계 파일 및 제품
설계 파일
바로 사용 가능한 시스템 파일을 다운로드하여 설계 프로세스에 속도를 높여 보십시오.
설계 구성요소, 참조 지정자 및 제조업체/부품 번호의 전체 목록
기술 자료
| 유형 | 직함 | 최신 영어 버전 다운로드 | 날짜 | ||
|---|---|---|---|---|---|
| * | 테스트 보고서 | TIDA-00012 Test Results | 2013. 9. 4 |