SWRS195C October   2019  – April 2024 CC2652P

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Functional Block Diagram
  6. 5 Device Comparison
  7. 6 Pin Configuration and Functions
    1. 6.1 Pin Diagram—RGZ Package (Top View)
    2. 6.2 Signal Descriptions—RGZ Package
    3. 6.3 Connections for Unused Pins and Modules
  8. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Power Supply and Modules
    5. 7.5  Power Consumption—Power Modes
    6. 7.6  Power Consumption—Radio Modes
    7. 7.7  Nonvolatile (Flash) Memory Characteristics
    8. 7.8  Thermal Resistance Characteristics
    9. 7.9  RF Frequency Bands
    10. 7.10 Bluetooth Low Energy—Receive (RX)
    11. 7.11 Bluetooth Low Energy—Transmit (TX)
    12. 7.12 Zigbee and Thread—IEEE 802.15.4-2006 2.4GHz (OQPSK DSSS1:8, 250kbps): RX
    13. 7.13 Zigbee and Thread—IEEE 802.15.4-2006 2.4GHz (OQPSK DSSS1:8, 250kbps): TX
    14. 7.14 Timing and Switching Characteristics
      1. 7.14.1 Reset Timing
      2. 7.14.2 Wakeup Timing
      3. 7.14.3 Clock Specifications
        1. 7.14.3.1 48MHz Crystal Oscillator (XOSC_HF)
        2. 7.14.3.2 48MHz RC Oscillator (RCOSC_HF)
        3. 7.14.3.3 2MHz RC Oscillator (RCOSC_MF)
        4. 7.14.3.4 32.768kHz Crystal Oscillator (XOSC_LF)
        5. 7.14.3.5 32kHz RC Oscillator (RCOSC_LF)
      4. 7.14.4 Synchronous Serial Interface (SSI) Characteristics
        1. 7.14.4.1 Synchronous Serial Interface (SSI) Characteristics
        2.       36
      5. 7.14.5 UART
        1. 7.14.5.1 UART Characteristics
    15. 7.15 Peripheral Characteristics
      1. 7.15.1 ADC
        1. 7.15.1.1 Analog-to-Digital Converter (ADC) Characteristics
      2. 7.15.2 DAC
        1. 7.15.2.1 Digital-to-Analog Converter (DAC) Characteristics
      3. 7.15.3 Temperature and Battery Monitor
        1. 7.15.3.1 Temperature Sensor
        2. 7.15.3.2 Battery Monitor
      4. 7.15.4 Comparators
        1. 7.15.4.1 Low-Power Clocked Comparator
        2. 7.15.4.2 Continuous Time Comparator
      5. 7.15.5 Current Source
        1. 7.15.5.1 Programmable Current Source
      6. 7.15.6 GPIO
        1. 7.15.6.1 GPIO DC Characteristics
    16. 7.16 Typical Characteristics
      1. 7.16.1 MCU Current
      2. 7.16.2 RX Current
      3. 7.16.3 TX Current
      4. 7.16.4 RX Performance
      5. 7.16.5 TX Performance
      6. 7.16.6 ADC Performance
  9. 8 Detailed Description
    1. 8.1  Overview
    2. 8.2  System CPU
    3. 8.3  Radio (RF Core)
      1. 8.3.1 Bluetooth 5.2 Low Energy
      2. 8.3.2 802.15.4 (Thread, Zigbee, 6LoWPAN)
    4. 8.4  Memory
    5. 8.5  Sensor Controller
    6. 8.6  Cryptography
    7. 8.7  Timers
    8. 8.8  Serial Peripherals and I/O
    9. 8.9  Battery and Temperature Monitor
    10. 8.10 µDMA
    11. 8.11 Debug
    12. 8.12 Power Management
    13. 8.13 Clock Systems
    14. 8.14 Network Processor
  10. 9 Application, Implementation, and Layout
    1. 9.1 Reference Designs
  11. 10Device and Documentation Support
    1. 10.1 Tools and Software
      1. 10.1.1 SimpleLink™ Microcontroller Platform
    2. 10.2 Documentation Support
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Packaging Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • RGZ|48
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.10 Bluetooth Low Energy—Receive (RX)

Measured on the CC1352PEM-XD7793-XD24-PA24 reference design with Tc = 25°C, VDDS = 3.0V, fRF= 2440MHz with
DC/DC enabled and the high-power PA connected to VDDS unless otherwise noted.
All measurements are performed at the antenna input with a combined RX and TX path, except for the high-power PA, which is measured at a dedicated antenna connection. All measurements are performed and conducted.
 
PARAMETERTEST CONDITIONSMINTYPMAXUNIT
125kbps (LE Coded)
Receiver sensitivityDifferential mode. BER = 10–3–105dBm
Receiver saturationDifferential mode. BER = 10–3>5dBm
Frequency error toleranceDifference between the incoming carrier frequency and the internally generated carrier frequency> (–300 / 300)kHz
Data rate error toleranceDifference between the incoming data rate and the internally generated data rate (37-byte packets)> (–320 / 240)ppm
Data rate error toleranceDifference between the incoming data rate and the internally generated data rate (255-byte packets)> (–125 / 125)ppm
Co-channel rejection(1)Wanted signal at –79dBm, modulated interferer in channel, BER = 10–3–1.5dB
Selectivity, ±1MHz(1)Wanted signal at –79dBm, modulated interferer at ±1MHz, BER = 10–38 / 4.5(2)dB
Selectivity, ±2MHz(1)Wanted signal at –79dBm, modulated interferer at ±2MHz, BER = 10–3 44 / 39(2)dB
Selectivity, ±3MHz(1)Wanted signal at –79dBm, modulated interferer at ±3MHz, BER = 10–346 / 44(2)dB
Selectivity, ±4MHz(1)Wanted signal at –79dBm, modulated interferer at ±4MHz, BER = 10–344 / 46(2)dB
Selectivity, ±6MHz(1)Wanted signal at –79dBm, modulated interferer at ≥ ±6MHz, BER = 10–348 / 44(2)dB
Selectivity, ±7MHzWanted signal at –79dBm, modulated interferer at ≥ ±7MHz, BER = 10–351 / 45(2)dB
Selectivity, Image frequency(1)Wanted signal at –79dBm, modulated interferer at image frequency, BER = 10–3dB
Selectivity, Image frequency ±1MHz(1)Note that Image frequency + 1MHz is the co-channel –1MHz. Wanted signal at –79dBm, modulated interferer at ±1MHz from image frequency, BER = 10–34.5 / 44 (2)dB
500kbps (LE Coded)
Receiver sensitivityDifferential mode. BER = 10–3–100dBm
Receiver saturationDifferential mode. BER = 10–3> 5dBm
Frequency error toleranceDifference between the incoming carrier frequency and the internally generated carrier frequency> (–300 / 300)kHz
Data rate error toleranceDifference between the incoming data rate and the internally generated data rate (37-byte packets)> (–450 / 450)ppm
Data rate error toleranceDifference between the incoming data rate and the internally generated data rate (255-byte packets)> (–175 / 175)ppm
Co-channel rejection(1)Wanted signal at –72dBm, modulated interferer in channel, BER = 10–3–3.5dB
Selectivity, ±1MHz(1)Wanted signal at –72dBm, modulated interferer at ±1MHz, BER = 10–38 / 4(2)dB
Selectivity, ±2MHz(1)Wanted signal at –72dBm, modulated interferer at ±2MHz, BER = 10–344 / 37(2)dB
Selectivity, ±3MHz(1)Wanted signal at –72dBm, modulated interferer at ±3MHz, BER = 10–346 / 46(2)dB
Selectivity, ±4MHz(1)Wanted signal at –72dBm, modulated interferer at ±4MHz, BER = 10–345 / 47(2)dB
Selectivity, ±6MHz(1)Wanted signal at –72dBm, modulated interferer at ≥ ±6MHz, BER = 10–346 / 45(2)dB
Selectivity, ±7MHzWanted signal at –72dBm, modulated interferer at ≥ ±7MHz, BER = 10–349 / 45(2)dB
Selectivity, Image frequency(1)Wanted signal at –72dBm, modulated interferer at image frequency, BER = 10–3dB
Selectivity, Image frequency ±1MHz(1)Note that Image frequency + 1MHz is the co-channel –1MHz. Wanted signal at –72dBm, modulated interferer at ±1MHz from image frequency, BER = 10–34 / 46(2)dB
1Mbps (LE 1M)
Receiver sensitivityDifferential mode. BER = 10–3–97dBm
Receiver saturationDifferential mode. BER = 10–3 > 5dBm
Frequency error toleranceDifference between the incoming carrier frequency and the internally generated carrier frequency> (–350 / 350)kHz
Data rate error toleranceDifference between the incoming data rate and the internally generated data rate (37-byte packets)> (–750 / 750)ppm
Co-channel rejection(1)Wanted signal at –67dBm, modulated interferer in channel, BER = 10–3–6dB
Selectivity, ±1MHz(1)Wanted signal at –67dBm, modulated interferer at ±1MHz, BER = 10–37 / 4(2)dB
Selectivity, ±2MHz(1)Wanted signal at –67dBm, modulated interferer at ±2MHz, BER = 10–340 / 33(2)dB
Selectivity, ±3MHz(1)Wanted signal at –67dBm, modulated interferer at ±3MHz, BER = 10–336 / 41(2)dB
Selectivity, ±4MHz(1)Wanted signal at –67dBm, modulated interferer at ±4MHz, BER = 10–336 / 45(2)dB
Selectivity, ±5MHz or more(1)Wanted signal at –67dBm, modulated interferer at ≥ ±5MHz, BER = 10–340dB
Selectivity, image frequency(1)Wanted signal at –67dBm, modulated interferer at image frequency, BER = 10–333dB
Selectivity, image frequency
±1MHz(1)		Note that Image frequency + 1MHz is the co-channel –1MHz. Wanted signal at –67dBm, modulated interferer at ±1MHz from image frequency, BER = 10–34 / 41(2)dB
Out-of-band blocking(3)30MHz to 2000MHz–10dBm
Out-of-band blocking2003MHz to 2399MHz–18dBm
Out-of-band blocking2484MHz to 2997MHz–12dBm
Out-of-band blocking3000MHz to 12.75GHz–2dBm
IntermodulationWanted signal at 2402MHz, –64 dBm. Two interferers at 2405MHz and 2408MHz, respectively, at the given power level –42dBm
Spurious emissions,
30MHz to 1000MHz(4)		Measurement in a 50Ω single-ended load< –59dBm
Spurious emissions,
1 to 12.75GHz(4)		Measurement in a 50Ω single-ended load< –47dBm
RSSI dynamic range70dB
RSSI accuracy±4dB
2Mbps (LE 2M)
Receiver sensitivityDifferential mode. Measured at SMA connector, BER = 10–3 –92dBm
Receiver saturationDifferential mode. Measured at SMA connector, BER = 10–3> 5dBm
Frequency error toleranceDifference between the incoming carrier frequency and the internally generated carrier frequency> (–500 / 500)kHz
Data rate error toleranceDifference between the incoming data rate and the internally generated data rate (37-byte packets)> (–700 / 750)ppm
Co-channel rejection(1)Wanted signal at –67dBm, modulated interferer in channel, BER = 10–3–7dB
Selectivity, ±2MHz(1)Wanted signal at –67dBm, modulated interferer at ±2MHz, Image frequency is at –2MHz, BER = 10–38 / 4(2)dB
Selectivity, ±4MHz(1)Wanted signal at –67dBm, modulated interferer at ±4MHz, BER = 10–336 / 36(2)dB
Selectivity, ±6MHz(1)Wanted signal at –67dBm, modulated interferer at ±6MHz, BER = 10–337 / 36(2)dB
Selectivity, image frequency(1)Wanted signal at –67dBm, modulated interferer at image frequency, BER = 10–34dB
Selectivity, image frequency
±2MHz(1)		Note that Image frequency + 2MHz is the Co-channel. Wanted signal at –67dBm, modulated interferer at ±2MHz from image frequency, BER = 10–3–7 / 36(2)dB
Out-of-band blocking(3)30MHz to 2000MHz–16dBm
Out-of-band blocking2003MHz to 2399MHz–21dBm
Out-of-band blocking2484MHz to 2997MHz–15dBm
Out-of-band blocking3000MHz to 12.75 GHz–12dBm
IntermodulationWanted signal at 2402MHz, –64 dBm. Two interferers at 2408 and 2414MHz respectively, at the given power level–38dBm
(1) Numbers given as I/C dB
(2) X / Y, where X is +N MHz and Y is –N MHz
(3) Excluding one exception at Fwanted / 2, per Bluetooth Specification
(4) Suitable for systems targeting compliance with worldwide radio-frequency regulations ETSI EN 300 328 and EN 300 440 Class 2 (Europe), FCC CFR47 Part 15 (US), and ARIB STD-T66 (Japan)