JAJSB30I August   2010  – April 2018 LM25119

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      代表的なアプリケーション回路
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Switching Characteristics
    7. 7.7 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  High Voltage Start-Up Regulator
      2. 8.3.2  UVLO
      3. 8.3.3  Enable 2
      4. 8.3.4  Oscillator and Sync Capability
      5. 8.3.5  Error Amplifiers and PWM Comparators
      6. 8.3.6  Ramp Generator
      7. 8.3.7  Current Limit
      8. 8.3.8  Hiccup Mode Current Limiting
      9. 8.3.9  Soft Start
      10. 8.3.10 HO and LO Output Drivers
      11. 8.3.11 Maximum Duty Cycle
      12. 8.3.12 Thermal Protection
    4. 8.4 Device Functional Modes
      1. 8.4.1 Diode Emulation
  9. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Miscellaneous Functions
      2. 9.1.2 Interleaved Two-Phase Operation
      3. 9.1.3 Interleaved 4-Phase Operation
    2. 9.2 Typical Applications
      1. 9.2.1 Dual-output Design Example
        1. 9.2.1.1 Design Requirements
          1. 9.2.1.1.1 External Components
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1  Timing Resistor
          2. 9.2.1.2.2  Output Inductor
          3. 9.2.1.2.3  Current Sense Resistor
          4. 9.2.1.2.4  Ramp Resistor and Ramp Capacitor
          5. 9.2.1.2.5  Output Capacitors
          6. 9.2.1.2.6  Input Capacitors
          7. 9.2.1.2.7  VCC Capacitor
          8. 9.2.1.2.8  Bootstrap Capacitor
          9. 9.2.1.2.9  Soft Start Capacitor
          10. 9.2.1.2.10 Restart Capacitor
          11. 9.2.1.2.11 Output Voltage Divider
          12. 9.2.1.2.12 UVLO Divider
          13. 9.2.1.2.13 MOSFET Selection
          14. 9.2.1.2.14 MOSFET Snubber
          15. 9.2.1.2.15 Error Amplifier Compensation
        3. 9.2.1.3 Application Curves
      2. 9.2.2 Two-Phase Design Example
        1. 9.2.2.1 Design Requirements
        2. 9.2.2.2 Detailed Design Procedure
        3. 9.2.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Switching Jitter Root Causes and Solutions
    2. 11.2 Layout Example
  12. 12デバイスおよびドキュメントのサポート
    1. 12.1 コミュニティ・リソース
    2. 12.2 商標
    3. 12.3 静電気放電に関する注意事項
    4. 12.4 Glossary
  13. 13メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

9.2.1.2.4 Ramp Resistor and Ramp Capacitor

The value of ramp capacitor (CRAMP) must be less than 2 nF to allow full discharge between cycles by the discharge switch internal to the LM25119 device . A good-quality, thermally-stable ceramic capacitor with 5% or less tolerance is recommended. For this design the value of CRAMP was set at the standard capacitor value of 820 pF. With the inductor, sense resistor and the K factor selected, the value of the ramp resistor (RRAMP) is calculated with Equation 19 and the example (Equation 20). The standard value of 34 kΩ was selected.

Equation 19. LM25119 30126240.gif
Equation 20. LM25119 30126267.gif