JAJSE48C August   2017  – April 2018 TAS5755M

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      効率と合計出力電力との関係
      2.      出力電力と電源電圧との関係
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
    1.     Pin Functions
  8. 8 Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Recommended Operating Conditions
    4. 8.4  Thermal Information
    5. 8.5  PWM Operation at Recommended Operating Conditions
    6. 8.6  DC Electrical Characteristics
    7. 8.7  AC Electrical Characteristics (BTL, PBTL)
    8. 8.8  Electrical Characteristics - PLL External Filter Components
    9. 8.9  Electrical Characteristic - I2C Serial Control Port Operation
    10. 8.10 Timing Requirements - PLL Input Parameters
    11. 8.11 Timing Requirements - Serial Audio Ports Slave Mode
    12. 8.12 Timing Requirements - I2C Serial Control Port Operation
    13. 8.13 Timing Requirements - Reset (RESET)
    14. 8.14 Typical Characteristics
      1. 8.14.1 Typical Characteristics, 2.1 SE Configuration
      2. 8.14.2 Typical Characteristics, 2.0 BTL Configuration
      3. 8.14.3 Typical Characteristics, PBTL Configuration
  9. 9 Parameter Measurement Information
  10. 10Detailed Description
    1. 10.1 Overview
    2. 10.2 Functional Block Diagrams
    3. 10.3 Feature Description
      1. 10.3.1  Power Supply
      2. 10.3.2  I2C Address Selection and Fault Output
      3. 10.3.3  Single-Filter PBTL Mode
      4. 10.3.4  Device Protection System
        1. 10.3.4.1 Overcurrent (OC) Protection With Current Limiting
        2. 10.3.4.2 Overtemperature Protection
        3. 10.3.4.3 Undervoltage Protection (UVP) and Power-On Reset (POR)
      5. 10.3.5  SSTIMER Functionality
      6. 10.3.6  Clock, Autodetection, and PLL
      7. 10.3.7  PWM Section
      8. 10.3.8  2.1-Mode Support
      9. 10.3.9  I2C Compatible Serial Control Interface
      10. 10.3.10 Audio Serial Interface
        1. 10.3.10.1 I2S Timing
        2. 10.3.10.2 Left-Justified
        3. 10.3.10.3 Right-Justified
      11. 10.3.11 Dynamic Range Control (DRC)
    4. 10.4 Device Functional Modes
      1. 10.4.1 Stereo BTL Mode
      2. 10.4.2 Mono PBTL Mode
      3. 10.4.3 2.1 Mode
    5. 10.5 Programming
      1. 10.5.1 I2C Serial Control Interface
        1. 10.5.1.1 General I2C Operation
        2. 10.5.1.2 Single- and Multiple-Byte Transfers
        3. 10.5.1.3 Single-Byte Write
        4. 10.5.1.4 Multiple-Byte Write
        5. 10.5.1.5 Single-Byte Read
        6. 10.5.1.6 Multiple-Byte Read
      2. 10.5.2 26-Bit 3.23 Number Format
    6. 10.6 Register Maps
      1. 10.6.1 Register Map Summary
      2. 10.6.2 Register Maps
        1. 10.6.2.1  Clock Control Register (0x00)
        2. 10.6.2.2  Device ID Register (0x01)
        3. 10.6.2.3  Error Status Register (0x02)
        4. 10.6.2.4  System Control Register 1 (0x03)
        5. 10.6.2.5  Serial Data Interface Register (0x04)
        6. 10.6.2.6  System Control Register 2 (0x05)
        7. 10.6.2.7  Soft Mute Register (0x06)
        8. 10.6.2.8  Volume Registers (0x07, 0x08, 0x09, 0x0A)
        9. 10.6.2.9  Volume Configuration Register (0x0E)
        10. 10.6.2.10 Modulation Limit Register (0x10)
        11. 10.6.2.11 Interchannel Delay Registers (0x11, 0x12, 0x13, and 0x14)
        12. 10.6.2.12 PWM Shutdown Group Register (0x19)
        13. 10.6.2.13 Start/Stop Period Register (0x1A)
        14. 10.6.2.14 Oscillator Trim Register (0x1B)
        15. 10.6.2.15 BKND_ERR Register (0x1C)
        16. 10.6.2.16 Input Multiplexer Register (0x20)
        17. 10.6.2.17 Channel 4 Source Select Register (0x21)
        18. 10.6.2.18 PWM Output Mux Register (0x25)
        19. 10.6.2.19 DRC Control Register (0x46)
        20. 10.6.2.20 Bank Switch and EQ Control Register (0x50)
  11. 11Application and Implementation
    1. 11.1 Application Information
    2. 11.2 Typical Applications
      1. 11.2.1 Stereo Bridge Tied Load Application
        1. 11.2.1.1 Design Requirements
        2. 11.2.1.2 Detailed Design Procedure
          1. 11.2.1.2.1 Component Selection and Hardware Connections
          2. 11.2.1.2.2 I2C Pullup Resistors
          3. 11.2.1.2.3 Digital I/O Connectivity
          4. 11.2.1.2.4 Recommended Start-Up and Shutdown Procedures
            1. 11.2.1.2.4.1 Initialization Sequence
            2. 11.2.1.2.4.2 Normal Operation
            3. 11.2.1.2.4.3 Shutdown Sequence
            4. 11.2.1.2.4.4 Power-Down Sequence
        3. 11.2.1.3 Application Curves
      2. 11.2.2 Mono Parallel Bridge Tied Load Application
        1. 11.2.2.1 Design Requirements
        2. 11.2.2.2 Detailed Design Procedure
        3. 11.2.2.3 Application Curves
      3. 11.2.3 2.1 Application
        1. 11.2.3.1 Design Requirements
        2. 11.2.3.2 Detailed Design Procedure
        3. 11.2.3.3 Application Curves
  12. 12Power Supply Recommendations
    1. 12.1 DVDD and AVDD Supplies
    2. 12.2 PVDD Power Supply
  13. 13Layout
    1. 13.1 Layout Guidelines
    2. 13.2 Layout Examples
  14. 14デバイスおよびドキュメントのサポート
    1. 14.1 デバイス・サポート
      1. 14.1.1 開発サポート
    2. 14.2 ドキュメントのサポート
      1. 14.2.1 関連資料
    3. 14.3 コミュニティ・リソース
    4. 14.4 商標
    5. 14.5 静電気放電に関する注意事項
    6. 14.6 Glossary

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

10.5.1.2 Single- and Multiple-Byte Transfers

The serial control interface supports both single-byte and multiple-byte read/write operations for subaddresses 0x00 to 0x1F. However, for the subaddresses 0x20 to 0xFF, the serial control interface supports only multiple-byte read/write operations (in multiples of 4 bytes).

During multiple-byte read operations, the DAP responds with data, a byte at a time, starting at the subaddress assigned, as long as the master device continues to respond with acknowledges. If a particular subaddress does not contain 32 bits, the unused bits are read as logic 0.

During multiple-byte write operations, the DAP compares the number of bytes transmitted to the number of bytes that are required for each specific subaddress. For example, if a write command is received for a biquad subaddress, the DAP must receive five 32-bit words. If fewer than five 32-bit data words have been received when a stop command (or another start command) is received, the received data is discarded.

Supplying a subaddress for each subaddress transaction is referred to as random I2C addressing. The TAS5755M also supports sequential I2C addressing. For write transactions, if a subaddress is issued followed by data for that subaddress and the 15 subaddresses that follow, a sequential I2C write transaction has taken place, and the data for all 16 subaddresses is successfully received by the TAS5755M. For I2C sequential-write transactions, the subaddress then serves as the start address, and the amount of data subsequently transmitted, before a stop or start is transmitted, determines how many subaddresses are written. As was true for random addressing, sequential addressing requires that a complete set of data be transmitted. If only a partial set of data is written to the last subaddress, the data for the last subaddress is discarded. However, all other data written is accepted; only the incomplete data is discarded.