JAJSOW5F April   2006  – January 2024 TPS5420

PRODUCTION DATA  

  1.   1
  2. 1特長
  3. 2アプリケーション
  4. 3概要
  5. 4静電気放電に関する注意事項
  6. 5Ordering Information
  7. 6Pin Assignments
    1. 6.1 Terminal Functions
  8. 7Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information 
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  9. 8Application Information
    1. 8.1 Functional Block Diagram
    2. 8.2 Detailed Description
      1. 8.2.1  Oscillator Frequency
      2. 8.2.2  Voltage Reference
      3. 8.2.3  Enable (ENA) and Internal Slow Start
      4. 8.2.4  Undervoltage Lockout (UVLO)
      5. 8.2.5  Boost Capacitor (BOOT)
      6. 8.2.6  Output Feedback (VSENSE)
      7. 8.2.7  Internal Compensation
      8. 8.2.8  Voltage Feed Forward
      9. 8.2.9  Pulse-Width-Modulation (PWM) Control
      10. 8.2.10 Overcurrent Limiting
      11. 8.2.11 Overvoltage Protection
      12. 8.2.12 Thermal Shutdown
      13. 8.2.13 PCB Layout
      14. 8.2.14 Application Circuits
      15. 8.2.15 Design Procedure
        1. 8.2.15.1  Design Parameters
        2. 8.2.15.2  Switching Frequency
        3. 8.2.15.3  Input Capacitors
        4. 8.2.15.4  Output Filter Components
          1. 8.2.15.4.1 Inductor Selection
          2. 8.2.15.4.2 Capacitor Selection
          3.        40
          4.        41
        5. 8.2.15.5  Output Voltage Setpoint
        6. 8.2.15.6  Boot Capacitor
        7. 8.2.15.7  Catch Diode
        8. 8.2.15.8  Additional Circuits
        9. 8.2.15.9  Circuit Using Ceramic Output Filter Capacitors
        10. 8.2.15.10 Output Filter Component Selection
        11. 8.2.15.11 External Compensation Network
    3. 8.3 Advanced Information
      1. 8.3.1 Output Voltage Limitations
      2. 8.3.2 Internal Compensation Network
      3. 8.3.3 Thermal Calculations
    4. 8.4 Performance Graphs
  10. 9Revision History

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

9 Revision History

Changes from Revision E (September 2013) to Revision F (January 2024)

  • 文書全体にわたって表、図、相互参照の採番方法を更新Go
  • Updated to new format which does not include specific parameter names and does include min and max columns.  TJ called out in header.  Pin names are used rather than signal names.  BOOT and PH voltages now marked as output voltage.  Footnotes updated and Note 2 removed.Go
  • Changed BOOT to PH Absolute Maximum to 6 V maximumGo
  • Deleted Absolute Maximum BOOT to GND maximum voltageGo
  • Added ESD tableGo
  • Added Recommended operating VI input voltageGo
  • Updated footnotes to match current TI standards, replaced custom board specifications with EVM information and JEDEC standard information.Go
  • Changed RθJC(top), RθJB, ψJT, ψJB Go
  • Added condition for typical specifications EC table’s header, added parameter names, and used pin names in parameter descriptions.  Footnote added.Go
  • Updated the following test conditions: VFB, DMAX, and RDSON(HS).Go
  • Updated the following typical specifications in the EC table: IQ(VIN), ISD(VIN), VINUVLO(H), VEN(H), and RDSON(HS).Go

Changes from Revision D (January 2013) to Revision E (September 2013)

  • データシートのタイトル、「特長」、「概要」から SWIFT を削除Go
  • 「特長」の「SWIFT のドキュメント」を削除Go
  • 「概要」から、「SWIFT™ ファミリの DC/DC レギュレータのメンバとして」を削除Go

Changes from Revision C (October 2007) to Revision D (January 2013)

  • Replaced the DISSIPATION RATINGS with the THERMAL INFORMATION tableGo

Changes from Revision B (November 2006) to Revision C (October 2007)

  • Changed From: KIND = 0.2, and the minimum inductor value is 31 μH To: KIND = 0.2, and the minimum inductor value is 27 μHGo