PGA308
Amplificador de sensor de alimentación única, con puesta a cero automática y ganancia y compensación
PGA308
- Digital Calibration for Bridge Sensors
- Offset Select: Coarse and Fine
- Gain Select: Coarse and Fine
- Bridge Fault Monitor
- Input Mux for Lead Swap
- Over/Under Scale Limits
- DOUT/VOUT Clamp Function
- Seven Banks OTP Memory
- One-Wire Digital UART Interface
- Operating Voltage: +2.7V to +5.5V
- Temperature Range: –40°C to +125°C
- MSOP-10 and 3mm × 4mm DFN-10 Packages
The PGA308 is a programmable analog sensor signal conditioner. The analog signal path amplifies the sensor signal and provides digital calibration for offset and gain. Calibration is done via the 1W pin, a digital One-Wire, UART-compatible interface. For three-terminal sensor modules, 1W may be connected to VOUT and the assembly programmed through the VOUT pin. Gain and offset calibration parameters are stored onboard in seven banks of one-time programmable (OTP) memory. The power-on reset (POR) OTP bank may be programmed a total of four times.
The all-analog signal path contains a 2×2 input multiplexer (mux) to allow electronic sensor lead swapping, a coarse offset adjust, an auto-zero programmable gain instrumentation amplifier (PGA), a fine gain adjust, a fine offset adjust, and a programmable gain output amplifier. Fault monitor circuitry detects and signals sensor burnout, overload, and system fault conditions. Over/under-scale limits provide additional means for system level diagnostics. The dual-use DOUT/VCLAMP pin can be used as a programmable digital output or as a VOUT over-voltage clamp.
For detailed application information, see the PGA308 User's Guide (SBOU069) available for download at www.ti.com.
Productos similares que pueden interesarle
Misma funcionalidad con diferente configuración de pines que el dispositivo comparado
Documentación técnica
Tipo | Título | Fecha | ||
---|---|---|---|---|
* | Data sheet | Single-Supply, Auto-Zero Sensor Amplifier with Programmable Gain and Offset datasheet (Rev. B) | 22 dic 2010 | |
Application brief | Multichannel Analog Input Modules for PLC Equipment | 04 ene 2019 | ||
EVM User's guide | PGA308EVM User's Guide (Rev. A) | 22 sep 2016 | ||
EVM User's guide | Multi-Cal-System Evaluation Module User's Guide (Rev. B) | 15 sep 2016 | ||
User guide | PGA308 User's Guide (Rev. B) | 27 ene 2012 | ||
User guide | Multi-Cal-PGA308 System User Guide | 29 abr 2011 | ||
User guide | Multi-Cal-Interface User's Guide | 09 sep 2010 | ||
User guide | Multi-Cal-Slave User's Guide | 09 sep 2010 | ||
User guide | Multi-Cal-Cable User's Guide | 08 sep 2010 | ||
User guide | Multi-Cal-Master User's Guide | 22 ago 2010 | ||
User guide | Multi-Cal-Test Users Guide | 22 ago 2010 | ||
User guide | tioScript Editor Users Guide | 26 ago 2008 | ||
User guide | USB DAQ Platform User's Guide | 20 mar 2008 |
Diseño y desarrollo
Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.
MULTI-CAL-SYSTEM — Kit de inicio básico de Multi-Cal-Sistema
The Multi-Cal-System is a system of evaluation modules and accessories that can be used to calibrate multiple PGA308 sensor modules. The Multi-Cal-System can be configured to calibrate from 8 to 64 PGA308s simultaneously. The key component of the Multi-Cal-System is the Multi-Cal-System Starter (...)
PGA308EVM — Módulo de evaluación PGA308
The PGA308EVM key hardware consists of two boards, PGA308 Test Board and USB DAQ Platform. The PGA308 Test Board contains the PGA308, terminal strips for external connections, several jumpers for device configuration, and support circuitry. The PGA308 Test Board can be used to fully test your (...)
SBOC257 — PGA308EVM Software
Productos y hardware compatibles
SBOC390 — Multi-Cal-PGA308 System Software
Productos y hardware compatibles
Productos
Amplificadores de ganancia programable y variable (PGA y VGA)
SBOC391 — Multi-Cal-PGA308 System Source Code
Productos y hardware compatibles
Productos
Amplificadores de ganancia programable y variable (PGA y VGA)
PSPICE-FOR-TI — PSpice® para herramienta de diseño y simulación de TI
TINA-TI — Programa de simulación analógica basado en SPICE
Paquete | Pasadores | Descargar |
---|---|---|
VSON (DRK) | 10 | Ver opciones |
VSSOP (DGS) | 10 | Ver opciones |
Pedidos y calidad
- RoHS
- REACH
- Marcado del dispositivo
- Acabado de plomo/material de la bola
- Clasificación de nivel de sensibilidad a la humedad (MSL) / reflujo máximo
- Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
- Contenido del material
- Resumen de calificaciones
- Monitoreo continuo de confiabilidad
- Lugar de fabricación
- Lugar de ensamblaje
Soporte y capacitación
Foros de TI E2E™ con asistencia técnica de los ingenieros de TI
El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.
Si tiene preguntas sobre la calidad, el paquete o el pedido de productos de TI, consulte el soporte de TI.