Inicio Gestión de la energía AC/DC & DC/DC controllers (external FET)
Inicio
Gestión de la energía
AC/DC & DC/DC controllers (external FET)

TPS53681

ACTIVO

Controlador multifásico reductor D-CAP+™ de doble canal 6+2/5+3, con NVM y PMBus

Haga su pedido ahora
Hoja de datos

TPS53681

ACTIVO
Hoja de datos Haga su pedido ahora

Detalles del producto

Vin (min) (V) 4.5 Vin (max) (V) 17 Iout (max) (A) 300 Operating temperature range (°C) -40 to 125 Control mode D-CAP+ Topology Multiphase Rating Catalog Vout (min) (V) 0.25 Vout (max) (V) 2.8125 Iq (typ) (A) 0.013 Duty cycle (max) (%) 50 Number of phases 8
Vin (min) (V) 4.5 Vin (max) (V) 17 Iout (max) (A) 300 Operating temperature range (°C) -40 to 125 Control mode D-CAP+ Topology Multiphase Rating Catalog Vout (min) (V) 0.25 Vout (max) (V) 2.8125 Iq (typ) (A) 0.013 Duty cycle (max) (%) 50 Number of phases 8
WQFN (RSB) 40 25 mm² 5 x 5
  • Conversion Input Voltage Range: 4.5 V to 17 V
  • 8-Bit DAC with Selectable 5 mV or 10 mV Resolution and Output Ranges from 0.25 V to 1.52 V or 0.5 to 2.8125 V for Dual Channels
  • Phase Configurations
    • Maximum (6-Phase + 2-Phase) or (5-Phase + 3-Phase)
    • Minimum (1-Phase + 1-Phase)
  • Driverless Configuration for Efficient High-Frequency Switching
  • Dynamic Output Voltage Transitions with Programmable Slew Rates via PMBus Interface
  • Frequency Selections with Closed-loop Frequency Control: 300 kHz to 1 MHz
  • Programmable Internal Loop Compensations
  • Configurable with Non-Volatile Memory (NVM) for Low External Component Counts
  • Individual Phase Current Calibrations and Reports
  • Dynamic Phase Shedding with Programmable Current Threshold for Optimizing Efficiency at Light and Heavy Loads
  • Fast Phase-Adding for Undershoot Reduction (USR)
  • Fully Compatible with TI NexFET™ Power Stage for High-Density Solutions
  • Accurate, Adjustable Voltage Positioning
  • Patented AutoBalance™ Phase Balancing
  • Selectable, 16-level Per-Phase Current Limit
  • PMBus™ System Interface for Telemetry of Voltage, Current, Power, Temperature, and Fault Conditions
  • Low Quiescent Current
  • 5 mm × 5 mm, 40-Pin, QFN PowerPad™ Package
  • Conversion Input Voltage Range: 4.5 V to 17 V
  • 8-Bit DAC with Selectable 5 mV or 10 mV Resolution and Output Ranges from 0.25 V to 1.52 V or 0.5 to 2.8125 V for Dual Channels
  • Phase Configurations
    • Maximum (6-Phase + 2-Phase) or (5-Phase + 3-Phase)
    • Minimum (1-Phase + 1-Phase)
  • Driverless Configuration for Efficient High-Frequency Switching
  • Dynamic Output Voltage Transitions with Programmable Slew Rates via PMBus Interface
  • Frequency Selections with Closed-loop Frequency Control: 300 kHz to 1 MHz
  • Programmable Internal Loop Compensations
  • Configurable with Non-Volatile Memory (NVM) for Low External Component Counts
  • Individual Phase Current Calibrations and Reports
  • Dynamic Phase Shedding with Programmable Current Threshold for Optimizing Efficiency at Light and Heavy Loads
  • Fast Phase-Adding for Undershoot Reduction (USR)
  • Fully Compatible with TI NexFET™ Power Stage for High-Density Solutions
  • Accurate, Adjustable Voltage Positioning
  • Patented AutoBalance™ Phase Balancing
  • Selectable, 16-level Per-Phase Current Limit
  • PMBus™ System Interface for Telemetry of Voltage, Current, Power, Temperature, and Fault Conditions
  • Low Quiescent Current
  • 5 mm × 5 mm, 40-Pin, QFN PowerPad™ Package

The TPS53681 is a multiphase step-down controller with dual channels, built-in non-volatile memory (NVM), and PMBus™ interface, and is fully compatible with TI NexFET ™power stage. Advanced control features such as D-CAP+™ architecture with undershoot reduction (USR) provide fast transient response, low output capacitance, and high efficiency. The device also provides novel phase interleaving strategy and dynamic phase shedding for efficiency improvement at different loads. The device supports fast dynamic voltage transitions with adjustable slew rate. In addition, the device supports the PMBus communication interface for reporting the telemetry of voltage, current, power, temperature, and fault conditions to the systems. All programmable parameters can be configured by the PMBus interface and can be stored in NVM as the new default values to minimize the external component count.

The TPS53681 device is offered in a thermally enhanced 40-pin QFN packaged and is rated to operate from –40°C to 125°C.

The TPS53681 is a multiphase step-down controller with dual channels, built-in non-volatile memory (NVM), and PMBus™ interface, and is fully compatible with TI NexFET ™power stage. Advanced control features such as D-CAP+™ architecture with undershoot reduction (USR) provide fast transient response, low output capacitance, and high efficiency. The device also provides novel phase interleaving strategy and dynamic phase shedding for efficiency improvement at different loads. The device supports fast dynamic voltage transitions with adjustable slew rate. In addition, the device supports the PMBus communication interface for reporting the telemetry of voltage, current, power, temperature, and fault conditions to the systems. All programmable parameters can be configured by the PMBus interface and can be stored in NVM as the new default values to minimize the external component count.

The TPS53681 device is offered in a thermally enhanced 40-pin QFN packaged and is rated to operate from –40°C to 125°C.
open-in-new Buscar otro/a AC/DC & DC/DC controllers (external FET)
Descargar Ver vídeo con transcripción Video

Productos similares que pueden interesarle

open-in-new Comparar alternativas
Funcionalidad similar a la del dispositivo comparado
TPS53647 ACTIVO Controlador reductor D-CAP+™ de 4 fases con interfaz NVM y PMBus para ASIC 4-Phase, single-output D-CAP+™ step-down buck controller with NVM and PMBus interface for ASIC.
TPS53667 ACTIVO Controlador reductor sin accionamiento D-CAP+ de 6 fases con interfaz NVM y PMBus para ASIC This is a 6-phase, single-output, D-CAP+ ™ step-down driverless buck controller with NVM and PMBus interface for AVS.
TPS536C7 ACTIVO Controlador PWM reductor multifásico D-CAP+™, de doble canal, PMBus (N+M ≤ 12 fases) 12-phase PMBus controller with dual outputs

Documentación técnica

star =Principal documentación para este producto seleccionada por TI
No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 13
Tipo Título Fecha
* Data sheet TPS53681 Dual-Channel (6-Phase + 2-Phase) or (5-Phase + 3-Phase) D-CAP+™ Step-Down Multiphase Controller with NVM and PMBus™ datasheet (Rev. B) PDF | HTML 09 ene 2019
Application note Multiphase Buck Design from Start to Finish, Part 1 (Rev. B) 07 abr 2021
Application note Selection Considerations for Output Capacitors of Multiphase Volt. Reg. Part 1 PDF | HTML 01 abr 2020
Technical article Minimize the impact of the MLCC shortage using D-CAP+™ control mode PDF | HTML 05 abr 2019
Application note D-CAP+TM Control for Multiphase Step-Down Voltage Regulators for Powering Microp 13 ene 2019
Technical article How to use PMBus power solutions for NXP QorIQ processors PDF | HTML 09 may 2018
Application note NVM Programming for VR13 Power Controllers PDF | HTML 04 may 2018
Selection guide DC/DC Buck Controller Solutions Selection Guide 06 feb 2018
EVM User's guide Using the TPS53681EVM 18 dic 2017
Technical article The D-CAP+™ Modulator: Evaluating the small-signal robustness PDF | HTML 15 nov 2017
Technical article Powering high-current Broadcom networking processors in Ethernet switches PDF | HTML 06 sep 2017
User guide TPS53681 Technical Reference Manual 25 abr 2017
User guide Using the Fusion Digital Power Designer for TPS536xx VR13 Multiphase Solutions 16 dic 2016

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Placa de evaluación

TPS53681EVM-002 — Módulo de evaluación de doble canal (6+2/5+3) para controlador reductor D-CAP+™ con interfaz PMBus

The TPS53681EVM evaluation module allows users to assess the operating characteristics of the TPS53681 controller with the CSD95490 smart power stages in a low voltage, high current, step-down point of load (POL) application with the configuration, control and monitoring functionality of the (...)

Guía del usuario: PDF
No disponible en TI.com
Software de aplicación y estructura

FUSION_DIGITAL_POWER_DESIGNER — Software de potencia digital

Fusion Digital Power™ graphical user interface (GUI) software is used to configure and monitor select Texas Instruments digital power controllers and sequencer/health monitors. The application uses the PMBus protocol to communicate with the device over serial bus by way of a TI USB adapter.
Descargar
Software de aplicación y estructura

FUSION_MFR_GUI — Herramienta de fabricación de Fusion Digital Power

The Fusion Digital Power Manufacturing Tool (aka MFR GUI) is a Graphical User Interface used to download firmware, upgrade firmware, configure, calibrate and test .

The MFR GUI supports the same devices as Fusion Digital Power Designer software.  This tool is typically used in manufacturing (...)

Descargar
Diseños de referencia

PMP22165 — Diseño de referencia de alimentación para la plataforma de aceleración computacional adaptativa (ACA

This reference design addresses Xilinx Versal adaptive compute acceleration platform (ACAP) requirements and consists of a power management integrated circuit (PMIC) for system rails plus a multiphase controller and power stages to support higher current processor loads.  On-board dynamic (...)
Test report: PDF
Esquema: PDF
Diseños de referencia

TIDA-050020 — Diseño de referencia de regulador de tensión PMBus™ para FPGA Xilinx® Virtex UltraScale+™

This reference design uses the TPS53681 multiphase controller and CSD95490Q5MC smart power stages to implement a high-performance design suitable for powering the 0.85-V, 200-A, VCCINT rail of a Xilinx™ Ultrascale+™ FPGA. The secondary output of the controller can then be used to power (...)
Design guide: PDF
Esquema: PDF
Diseños de referencia

TIDA-01512 — Diseño de referencia del regulador de tensión PMBus para procesadores NXP QorIQ LS2085A/88A

TIDA-01512 uses the TPS53681 multiphase controller and CSD95490Q5MC Smart Power Stages to implement a high-performance design suitable for powering NXP QorIQ Communications Processors.

The dual outputs of the controller target the 60-ATDC, 1.0-V core rail with a four-phase design and a 30-ATDC, (...)

Design guide: PDF
Esquema: PDF
Paquete Pasadores Descargar
WQFN (RSB) 40 Ver opciones
Se aplican los Términos y condiciones estándar de TI para los elementos de evaluación.

Pedidos y calidad

Información incluida:
  • RoHS
  • REACH
  • Marcado del dispositivo
  • Acabado de plomo/material de la bola
  • Clasificación de nivel de sensibilidad a la humedad (MSL) / reflujo máximo
  • Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
  • Contenido del material
  • Resumen de calificaciones
  • Monitoreo continuo de confiabilidad
Información incluida:
  • Lugar de fabricación
  • Lugar de ensamblaje

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

Ver todos los temas del foro en inglés

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene preguntas sobre la calidad, el paquete o el pedido de productos de TI, consulte el soporte de TI. ​​​​​​​​​​​​​​

Videos