TAS2563
- Key Features
- 11.5V, 12-step Look-Ahead Class-H boost
- Integrated DSP
- Full Scale Ultrasonic Output to 40kHz
- 2 PDM Microphone inputs
- Powerful Class-D Audio Amplifier :
- 6.1W 1% THD+N (4Ω, 3.6V)
- 5W 1% THD+N (8Ω, 3.6V)
- 10W 1% THD+N (4Ω, 12V)
- Protection Features:
- Real-Time I/V-Sense Speaker Protection
- Speaker Thermal & Over-Excursion Protection
- Short and Open Load Protection
- Thermal and Over-Current Protection
- Advanced Audio Processing
- Dedicated Real-Time DSP with:
- 10-Band Equalizer
- 3-Band Dynamic EQ
- Dynamic Range Compression
- Psychoacoustic Bass
- Dedicated Real-Time DSP with:
- Flexible Interfaces and Control :
- I2S/TDM: 8 Channels of 32 Bit up to 96KSPS
- I2C: Selectable Addresses with Fast Mode+
- Inter-Chp Communication Bus (DSBGA)
- 8kHz to 96kHz Sample Rates
- Power Efficiency and Flexibility :
- 83.5% Efficiency at W
- <1uA HW Shutdown VBAT Current
- Boost-Bypass Mode
- Power Supplies and Management
- VBAT: 2.5V to 5.5V
- VDD: 1.62V to 1.95V
- PVDD: VBAT to 13V (QFN)
-
PVDD: VBAT to 15V (QFN, VBAT < 3.5V)
- PVDD: VBAT to 16V (DSBGA)
- IOVDD: 1.65V to 3.6V
- VBAT Tracking Peak Voltage Limiter
- Advanced Brown Out Prevention
The TAS2563 is a digital input Class-D audio amplifier optimized for efficiently driving high peak power into small loudspeakers. The Class-D amplifier is capable of delivering 6.1W of peak power into a 4Ω load at battery voltage of 3.6V using the integrated 11.5V Class-H boost, or 10W peak power into 4Ω load in boost bypass mode using external 12V supply.
An on-chip, low-latency DSP supports Texas Instruments SmartAmp speaker protection algorithms. The integrated current and voltage sense provides for real-time monitoring of the loudspeakers, which permits pushing peak sound pressure levels (SPL) while keeping speakers from being damaged.
The integrated look-ahead Class-H boost dynamically adjusts boost voltage during playback, increasing efficiency and saving battery life in battery-powered systems. For regulated wall-powered systems, TAS2563 also features a boost bypass mode, supporting supply voltages of up to 16V for even higher output power.
Two PDM microphone inputs simplify the audio signal chain for two-way audio systems, interfacing digital microphones with the host processor. A battery-tracking peak voltage limiter with brown-out protection prevents systems shutdowns by optimizing amplifier headroom over the entire charge cycle.
TAS2563 소프트웨어 및 기타 설계 리소스에 대한 액세스를 요청하십시오. 장치의 DSBGA 또는 QFN 버전을 사용할 것인지 지정하십시오. 지금 요청
기술 문서
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
PP-SALB2-EVM — PP-SALB2-EVM 스마트 증폭기 스피커 특성화 보드 평가 모듈(학습 보드 2)
This board supports: TAS2555YZEVM, TAS2557EVM and TAS2559EVM.
The Smart Amplifier Speaker Characterization Board, when used in conjunction with a supported TI Smart Amplifier and PurePath Console software, provides users the ability to measure speaker excursion, temperature and other parameters for (...)
PPC3-EVM-MB — 스마트 증폭기 도터 카드 평가 모듈용 PPC3-EVM-MB 마더보드
TAS2563YBGEVM-DC — DSP 도터 카드가 통합된 TAS2563 DSBGA 6W 스마트 증폭기 평가 모듈(마더보드 필요)
The TAS2563YBGEVM-DC daughter card evaluation module (EVM) is designed to be used in conjunction with the PPC3-EVM-MB. This EVM provides the designer with the tools to integrate our SmartAmp portfolio into their application. The onboard DSP of the TAS2563 device enables the designer to characterize (...)
TAS2X63EVM — TAS2563 QFN 6W 스마트 증폭기(DSP 독립형 평가 모듈 통합)
PUREPATHCONSOLE — 오디오 시스템 설계 및 개발을 위한 PurePath™ 콘솔 그래픽 개발 제품군
PurePath Console’s (...)
TAS2XXX-DRIVERS — TAS25XX 및 TAS27XX 시리즈 클래스 D 증폭기를 위한 Android 및 기타 드라이버
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
패키지 | 핀 | 다운로드 |
---|---|---|
DSBGA (YBG) | 42 | 옵션 보기 |
VQFN-HR (RPP) | 32 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.