支援軟體
BQ2415XEVM-SW — BQ2415x EVM Sowtware Setup
The BQ2415x EVM Software provides a software interface for the BQ24150/1 EVM boards. Use this software to change the BQ24150/1 IC registers via the USB Interface Adapter.
儘管為了支援以前的設計而繼續生產此項產品，但我們並不建議用在新設計上。考量下列其中一項替代產品：
功能相同，但引腳輸出與所比較的產品不同
BQ24152
- Charge Faster than Linear Chargers
- High-Accuracy Voltage and Current Regulation
- Input Current Regulation Accuracy: ±5% (100 mA and 500 mA)
- Charge Voltage Regulation Accuracy: ±0.5% (25°C), ±1% (0°C-125°C)
- Charge Current Regulation Accuracy: ±5%
- High-Efficiency Mini-USB/AC Battery Charger for Single-Cell Li-Ion and Li-Polymer Battery Packs
- 20-V Absolute Maximum Input Voltage Rating
- 6-V Maximum Operating Input Voltage
- Built-In Input Current Sensing and Limiting
- Integrated Power FETs for Up To 1.25-A Charge Rate
- Programmable Charge Parameters through I2C Interface (up to 3.4 Mbps):
- Input Current
- Fast-Charge/Termination Current
- Charge Voltage (3.5 V to 4.44 V)
- Safety Timer with Reset Control
- Termination Enable
- Synchronous Fixed-Frequency PWM Controller Operating at 3 MHz with 0% to 99.5% Duty Cycle
- Automatic High Impedance Mode for Low Power Consumption
- Robust Protection
- Reverse Leakage Protection Prevents Battery Drainage
- Thermal Regulation and Protection
- Input/Output Overvoltage Protection
- Status Output for Charging and Faults
- USB Friendly Boot-Up Sequence
- Automatic Charging
- Power Up System without Battery
- Boost Mode Operation for USB OTG:
- Input Voltage Range (from Battery): 2.5 V to 4.5 V
- Output for VBUS: 5.05 V/ 200 mA
- 2 x 2 mm 20-Pin WCSP Package
- APPLICATIONS
- Mobile and Smart Phones
- MP3 Players
- Handheld Devices
The bq24152 is a compact, flexible, high-efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I2C interface. The bq24152 integrates a synchronous PWM controller, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package.
The bq24152 charges the battery in three phases: conditioning, constant current and constant voltage. The input current is automatically limited to the value set by the host. Charge is terminated based on user-selectable minimum current level. A safety timer with reset control provides a safety backup for I2C interface. During normal operation, bq24152 automatically restarts the charge cycle if the battery voltage falls below an internal threshold and automatically enters sleep mode or high impedance mode when the input supply is removed. The charge status is reported to the host using the I2C interface.
During the charging process, the bq24152 monitors its junction temperature (TJ) and reduces the charge current once TJ increases to approximately 125°C. To support USB OTG device, bq24152 provides VBUS (approximately 5.05V) by boosting the battery voltage. The bq24152 is available in 20-pin WCSP package.
技術文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 4 | 類型 | 標題 | 日期 | ||
|---|---|---|---|---|
| * | Data sheet | Fully Integrated Switch-Mode One-Cell Li-Ion Charger with Full USB Compliance** datasheet (Rev. A) | 2010年 1月 19日 | |
| Application note | Building your own Battery Simulator | 2013年 10月 14日 | ||
| User guide | bq2415x YFF EVM (HPA256) (Rev. C) | 2011年 6月 21日 | ||
| EVM User's guide | bq2415x RGY EVM User's Guide (Rev. A) | 2010年 4月 1日 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
驅動程式或資料庫
BQ2415XSW-LINUX — 適用於 BQ2415X 的 Linux 驅動程式
The Linux driver supports the BQ2415x series of fully integrated switch-mode one-cell Li-ion chargers. The Linux driver supports communication through the I2C bus and interfaces with the power supply sub-system.
Linux mainline status
Available in Linux mainline: Yes
Available through git.ti.com: (...)
| 封裝 | 引腳 | 下載 |
|---|---|---|
| DSBGA (YFF) | 20 | 檢視選項 |
訂購與品質
內含資訊：
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 資格摘要
- 進行中可靠性監測
內含資訊：
- 晶圓廠位置
- 組裝地點