SBAS969 September   2026 ADS111C02

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Timing Requirements
    7. 6.7 Timing Diagram
  8. 7 Parameter Measurement Information
    1. 7.1 Noise Performance
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagrams
    3. 8.3 Feature Description
      1. 8.3.1 Multiplexer
      2. 8.3.2 Voltage Reference
      3. 8.3.3 Oscillator
      4. 8.3.4 Output Data Rate and Conversion Time
      5. 8.3.5 Low-Noise PGA
      6. 8.3.6 Temperature Sensor
        1. 8.3.6.1 12-Bit Temperature Data Format (ADS101C0x)
        2. 8.3.6.2 Converting from Digital Codes to Temperature, 12-Bit Temperature Sensor Data
        3. 8.3.6.3 14-Bit Temperature Data Format (ADS101C0x)
        4. 8.3.6.4 Converting from Digital Codes to Temperature, 14-Bit Temperature Sensor Data
      7. 8.3.7 Digital Comparator
      8. 8.3.8 Conversion-Ready Pin
      9. 8.3.9 SMBus Alert Response
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power-Up and Reset
      2. 8.4.2 Operating Modes
        1. 8.4.2.1 Single-Shot Conversion Mode
        2. 8.4.2.2 Continuous-Conversion Mode
    5. 8.5 Programming
      1. 8.5.1 I2C Interface
      2. 8.5.2 I2C Address Selection
      3. 8.5.3 Serial Clock (SCL) and Serial Data (SDA)
      4. 8.5.4 I2C Interface Speed
      5. 8.5.5 I2C Data Transfer Protocol
      6. 8.5.6 Writing To and Reading From the Registers
      7. 8.5.7 Timeout
      8. 8.5.8 I2C General-Call (Software Reset)
    6. 8.6 Conversion Data Format
  10. 9 Register Maps
  11. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Serial Interface Connections
      2. 10.1.2 Connecting Multiple Devices
      3. 10.1.3 Single-Ended Inputs
      4. 10.1.4 Unused Inputs and Outputs
      5. 10.1.5 Input Protection
      6. 10.1.6 Analog Input Filtering
      7. 10.1.7 Duty Cycling For Low Power
      8. 10.1.8 I2C Communication Sequence Example
    2. 10.2 Typical Applications
      1. 10.2.1 K-Type Thermocouple with Thermistor Cold-Junction Compensation
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedure
      2. 10.2.2 Server Card System Monitoring Application
    3. 10.3 Power Supply Recommendations
      1. 10.3.1 Power-Supply Sequencing
      2. 10.3.2 Power-Supply Decoupling
    4. 10.4 Layout
      1. 10.4.1 Layout Guidelines
      2. 10.4.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Noise Performance

Delta-sigma (ΔΣ) analog-to-digital converters (ADCs) are based on the principle of oversampling. The input signal of a ΔΣ ADC is sampled at a high frequency (modulator frequency) and subsequently filtered and decimated in the digital domain to yield a conversion result at the respective output data rate. The ratio between modulator frequency and output data rate is called oversampling ratio (OSR). By increasing the OSR, and thus reducing the output data rate, the noise performance of the ADC can be optimized. In other words, the input-referred noise drops when reducing the output data rate because more samples of the internal modulator are averaged to yield one conversion result. Increasing the gain also reduces the input-referred noise, which is particularly useful when measuring low-level signals.

Table 7-1 and Table 7-2 show the input-referred noise in units of μVRMS for the conditions shown. The effective resolution values are shown in parenthesis. The effective resolution is calculated from μVRMS values using the following equation. Data are representative of typical noise performance at TA = 25°C with the inputs shorted together externally using two's compliment data coding.

Equation 1. E f f e c t i v e   R e s o l u t i o n = ln ⁡ 2 × V R E F G a i n × V R M S   N o i s e   ÷ ln ⁡ 2
Table 7-1 Noise in μVRMS (Effective Resolution) for 12-Bit Device at VDD = 3.3V
DATA RATE
(SPS)
GAIN
1/6 1/4 1/2 1 2 4 8 16
100 45.4 (12) 32.8 (12) 15.9 (12) 8.1 (12) 4.6 (12) 4.6 (12) 4.6 (12) 4.6 (12)
500 90.6 (12) 60.9 (12) 29.3 (12) 15.0 (12) 7.7 (12) 7.6 (12) 7.4 (12) 7.3 (12)
2000 172 (12) 114 (12) 56.9 (12) 28.6 (12) 14.4 (12) 14.3 (12) 14.3 (12) 14.3 (12)
6000 412 (12) 274 (12) 136 (12) 68.3 (12) 35.8 (12) 35.8 (12) 35.4 (12) 34.7 (11.8)
Table 7-2 Noise in μVRMS (Effective Resolution) for 16-Bit Device at VDD = 3.3V
DATA RATE
(SPS)
GAIN
1/6 1/4 1/2 1 2 4 8 16
10 9.8 (16) 6.9 (16) 3.4 (16) 1.6 (16) 0.83 (16) 0.83 (16) 0.83 (16) 0.83 (16)
100 32.6 (16) 22.2 (16) 11.0 (16) 5.4 (16) 2.7 (16) 2.7 (16) 2.7 (16) 2.7 (16)
1000 112 (16) 74.5 (16) 37.2 (16) 18.6 (16) 9.2 (16) 9.2 (15.7) 9.2 (14.7) 9.2 (13.7)
4000 307 (15.3) 204 (15.3) 102 (15.3) 51.3 (15.3) 25.6 (15.3) 25.6 (14.3) 25.6 (13.3) 25.6 (12.3)