SNLS656D August   2020  – December 2023 DP83TD510E

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
    1.     Pin Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Timing Diagrams
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Auto-Negotiation (Speed Selection)
      2. 6.3.2  Repeater Mode
      3. 6.3.3  Media Converter
      4. 6.3.4  Clock Output
      5. 6.3.5  Media Independent Interface (MII)
      6. 6.3.6  Reduced Media Independent Interface (RMII)
      7. 6.3.7  RMII Low Power 5-MHz Mode
      8. 6.3.8  RGMII Interface
      9. 6.3.9  Serial Management Interface
      10. 6.3.10 Extended Register Space Access
        1. 6.3.10.1 Read (No Post Increment) Operation
        2. 6.3.10.2 Read (Post Increment) Operation
        3. 6.3.10.3 Write (No Post Increment) Operation
        4. 6.3.10.4 Write (Post Increment) Operation
      11. 6.3.11 Loopback Modes
        1. 6.3.11.1 MII Loopback
        2. 6.3.11.2 PCS Loopback
        3. 6.3.11.3 Digital Loopback
        4. 6.3.11.4 Analog Loopback
        5. 6.3.11.5 Far-End (Reverse) Loopback
      12. 6.3.12 BIST Configurations
      13. 6.3.13 Cable Diagnostics
        1. 6.3.13.1 TDR
        2. 6.3.13.2 Fast Link Down Functionality
    4. 6.4 Device Functional Modes
      1. 6.4.1 Straps Configuration
        1. 6.4.1.1 Straps for PHY Address
    5. 6.5 Programming
    6. 6.6 MMD Register Address Map
    7. 6.7 DP83TD510E Registers
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Applications
      1. 7.2.1 Termination Circuit
        1. 7.2.1.1 Termination Circuit for Intrinsic Safe Applications
        2. 7.2.1.2 Components Range for Power Coupling/Decoupling
        3. 7.2.1.3 Termination Circuit for Non-Intrinsic Safe Applications
        4. 7.2.1.4 CMC Specifications
      2. 7.2.2 Design Requirements
        1. 7.2.2.1 Clock Requirements
          1. 7.2.2.1.1 Oscillator
          2. 7.2.2.1.2 Crystal
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
        1. 7.4.1.1 Signal Traces
        2. 7.4.1.2 Return Path
        3. 7.4.1.3 Metal Pour
        4. 7.4.1.4 PCB Layer Stacking
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
    2. 8.2 Support Resources
    3. 8.3 Trademarks
    4. 8.4 Electrostatic Discharge Caution
    5. 8.5 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.4.1.1 Signal Traces

PCB traces are lossy and long traces can degrade signal quality. Keep traces as short as possible. Unless mentioned otherwise, all signal traces must be 50-Ω single-ended impedance. Differential traces must 100-Ω differential. Take care to ensure impedance is controlled throughout. Impedance discontinuities cause reflections leading to emissions and signal integrity issues. Stubs should be avoided on all signal traces, especially differential signal pairs.

GUID-0F681C6F-3650-4AEC-A84B-40CDC1BACDA5-low.pngFigure 7-7 Differential Signal Traces

Within the differential pairs, trace lengths should be run parallel to each other and matched in length. Matched lengths minimize delay differences, avoiding an increase in common mode noise and emissions. Length matching is also important for MAC interface connections. All RMII transmit signal traces should be length matched to each other and all RMII receive signal traces should be length matched to each other.

Ideally, there should be no crossover or vias on signal path traces. Vias present impedance discontinuities and should be minimized when possible. Route trace pairs on the same layer. Signals on different layers should not cross each other without at least one return path plane between them. Differential pairs should always have a constant coupling distance between them. For convenience and efficiency, TI recommends routing critical signals first (that is, MDI differential pairs, reference clock, and MAC IF traces).