SLVSG23C December   2021  – August 2022 DRV8243-Q1

PRODUCTION DATA  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Device Comparison
  6. Pin Configuration and Functions
    1. 6.1 HW Variant
      1. 6.1.1 HVSSOP (28) package
      2. 6.1.2 VQFN-HR (14) package
    2. 6.2 SPI Variant
      1. 6.2.1 HVSSOP (28) package
      2. 6.2.2 VQFN-HR (14) package
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
      1. 7.5.1  Power Supply & Initialization
      2. 7.5.2  Logic I/Os
      3. 7.5.3  SPI I/Os
      4. 7.5.4  Configuration Pins - HW Variant Only
      5. 7.5.5  Power FET Parameters
      6. 7.5.6  Switching Parameters with High-Side Recirculation
      7. 7.5.7  Switching Parameters with Low-Side Recirculation
      8. 7.5.8  IPROPI & ITRIP Regulation
      9. 7.5.9  Over Current Protection (OCP)
      10. 7.5.10 Over Temperature Protection (TSD)
      11. 7.5.11 Voltage Monitoring
      12. 7.5.12 Load Monitoring
      13. 7.5.13 Fault Retry Setting
      14. 7.5.14 Transient Thermal Impedance & Current Capability
    6. 7.6 SPI Timing Requirements
    7. 7.7 Switching Waveforms
      1. 7.7.1 Output switching transients
        1. 7.7.1.1 High-Side Recirculation
        2. 7.7.1.2 Low-Side Recirculation
      2. 7.7.2 Wake-up Transients
        1. 7.7.2.1 HW Variant
        2. 7.7.2.2 SPI Variant
      3. 7.7.3 Fault Reaction Transients
        1. 7.7.3.1 Retry setting
        2. 7.7.3.2 Latch setting
    8. 7.8 Typical Characteristics
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
      1. 8.2.1 HW Variant
      2. 8.2.2 SPI Variant
    3. 8.3 Feature Description
      1. 8.3.1 External Components
        1. 8.3.1.1 HW Variant
        2. 8.3.1.2 SPI Variant
      2. 8.3.2 Bridge Control
        1. 8.3.2.1 PH/EN mode
        2. 8.3.2.2 PWM mode
        3. 8.3.2.3 Independent mode
        4. 8.3.2.4 Register - Pin Control - SPI Variant Only
      3. 8.3.3 Device Configuration
        1. 8.3.3.1 Slew Rate (SR)
        2. 8.3.3.2 IPROPI
        3. 8.3.3.3 ITRIP Regulation
        4. 8.3.3.4 DIAG
          1. 8.3.3.4.1 HW variant
          2. 8.3.3.4.2 SPI variant
      4. 8.3.4 Protection and Diagnostics
        1. 8.3.4.1 Over Current Protection (OCP)
        2. 8.3.4.2 Over Temperature Protection (TSD)
        3. 8.3.4.3 Off-State Diagnostics (OLP)
        4. 8.3.4.4 On-State Diagnostics (OLA) - SPI Variant Only
        5. 8.3.4.5 VM Over Voltage Monitor
        6. 8.3.4.6 VM Under Voltage Monitor
        7. 8.3.4.7 Power On Reset (POR)
        8. 8.3.4.8 Event Priority
    4. 8.4 Device Functional States
      1. 8.4.1 SLEEP State
      2. 8.4.2 STANDBY State
      3. 8.4.3 Wake-up to STANDBY State
      4. 8.4.4 ACTIVE State
      5. 8.4.5 nSLEEP Reset Pulse (HW Variant Only)
    5. 8.5 Programming - SPI Variant Only
      1. 8.5.1 SPI Interface
      2. 8.5.2 Standard Frame
      3. 8.5.3 SPI Interface for Multiple Peripherals
        1. 8.5.3.1 Daisy Chain Frame for Multiple Peripherals
    6. 8.6 Register Map - SPI Variant Only
      1. 8.6.1 User Registers
  9. Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Load Summary
    2. 9.2 Typical Application
      1. 9.2.1 HW Variant
      2. 9.2.2 SPI Variant
  10. 10Power Supply Recommendations
    1. 10.1 Bulk Capacitance Sizing
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Documentation Support
      1. 12.1.1 Related Documentation
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 Community Resources
    4. 12.4 Trademarks
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

SPI Interface

The SPI variant has full-duplex, 4-wire synchronous communication that is used to set device configurations, operating parameters, and read out diagnostic information from the device. The SPI operates in peripheral mode and connects to a controller. The serial data input (SDI) word consists of a 16-bit word, with an 8-bit command (A1), followed by 8-bit data (D1). The serial data output (SDO) word consists of the FAULT_SUMMARY byte (S1), followed by a report byte (R1). The report byte is either the register data being accessed by read command or null for a write command. The data sequence between the MCU and the SPI peripheral driver is shown in Figure 8-10.

GUID-2C12F1DA-D8CC-4DC8-B81E-4BD7A025A2BF-low.gifFigure 8-10 SPI Data - Standard "16-bit" Frame

A valid frame must meet the following conditions:

  • SCLK pin should be low when the nSCS pin transitions from high to low and from low to high.
  • nSCS pin should be pulled high between words.
  • When nSCS pin is pulled high, any signals at the SCLK and SDI pins are ignored and the SDO pin is placed in the Hi-Z state.
  • Data on SDO from the device is propagated on the rising edge of SCLK, while data on SDI is captured by the device on the subsequent falling edge of SCLK.
  • The most significant bit (MSB) is shifted in and out first.
  • A full 16 SCLK cycles must occur for a valid transaction for a standard frame, or alternately, for a daisy chain frame with "n" number of peripheral devices, 16 + (n x 16) SCLK cycles must occur for a valid transaction. Else, a frame error (SPI_ERR) is reported and the data is ignored if it is a WRITE operation.