SNOSDE2A October   2022  – December 2022 LMG2610

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  7. 7 Parameter Measurement Information
    1. 7.1 GaN Power FET Switching Parameters
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  GaN Power FET Switching Capability
      2. 8.3.2  Turn-On Slew-Rate Control
      3. 8.3.3  Current-Sense Emulation
      4. 8.3.4  Bootstrap Diode Function
      5. 8.3.5  Input Control Pins (EN, INL, INH)
      6. 8.3.6  INL - INH Interlock
      7. 8.3.7  AUX Supply Pin
        1. 8.3.7.1 AUX Power-On Reset
        2. 8.3.7.2 AUX Under-Voltage Lockout (UVLO)
      8. 8.3.8  BST Supply Pin
        1. 8.3.8.1 BST Power-On Reset
        2. 8.3.8.2 BST Under-Voltage Lockout (UVLO)
      9. 8.3.9  Over-Current Protection
      10. 8.3.10 Over-Temperature Protection
      11. 8.3.11 Fault Reporting
    4. 8.4 Device Functional Modes
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Turn-On Slew-Rate Design
        2. 9.2.2.2 Current-Sense Design
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
        1. 9.4.1.1 Solder-Joint Stress Relief
        2. 9.4.1.2 Signal-Ground Connection
        3. 9.4.1.3 CS Pin Signal
      2. 9.4.2 Layout Example
  10. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  11. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
  • RRG|40
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.2.2.1 Turn-On Slew-Rate Design

The LMG2610 turn-on slew rates are programmed as discussed in Turn-On Slew-Rate Control. In normal active-clamp flyback (ACF) operation the high-side power switch operates at zero-voltage switching (ZVS), so the high-side turn-on time does not affect the switch node slew rate. Therefore, the high-side GaN power FET is programmed to turn on as fast as possible to minimize high-side GaN power-FET third-quadrant losses. The fastest high-side turn-on time is programmed by setting

Equation 5. RDRVH < 5.6 kΩ

In normal ACF operation, the low-side power switch operates at both ZVS and non-ZVS valley switching depending on the load condition. The valley switching occurs at zero transformer current. Therefore, the low-side is programmed to turn on as slow as possible to minimize EMI and circuit ringing with no additional switching loss penalty. The slowest low-side turn-on time is programmed by setting

Equation 6. RDRVL > 120 kΩ