SLDS145D October   2001  – February 2024 TFP410

PRODUCTION DATA  

  1.   1
  2. Features
  3. Applications
  4. Description
  5. Pin Configuration and Functions
  6. Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Typical Characteristics
  7. Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 T.M.D.S. Pixel Data and Control Signal Encoding
      2. 6.3.2 Universal Graphics Controller Interface Voltage Signal Levels
      3. 6.3.3 Universal Graphics Controller Interface Clock Inputs
    4. 6.4 Device Functional Modes
      1. 6.4.1 Universal Graphics Controller Interface Modes
      2. 6.4.2 Data De-skew Feature
      3. 6.4.3 Hot Plug/Unplug (Auto Connect/Disconnect Detection)
      4. 6.4.4 Device Configuration and I2C RESET Description
      5. 6.4.5 DE Generator
    5. 6.5 Programming
      1. 6.5.1 I2C Interface
    6. 6.6 Register Maps
      1. 6.6.1  VEN_ID Register (Sub-Address = 01−00 ) [reset = 0x014C]
      2. 6.6.2  DEV_ID Register (Sub-Address = 03–02) [reset = 0x0410]
      3. 6.6.3  REV_ID Register (Sub-Address = 04) [reset = 0x00]
      4. 6.6.4  Reserved Register (Sub-Address = 07–05) [reset = 0x641400]
      5. 6.6.5  CTL_1_MODE (Sub-Address = 08) [reset = 0xBE]
      6. 6.6.6  CTL_2_MODE Register (Sub-Address = 09) [reset = 0x00]
      7. 6.6.7  CTL_3_MODE Register (Sub-Address = 0A) [reset = 0x80]
      8. 6.6.8  CFG Register (Sub-Address = 0B)
      9. 6.6.9  RESERVED Register (Sub-Address = 0E–0C) [reset = 0x97D0A9]
      10. 6.6.10 DE_DLY Register (Sub-Address = 32) [reset = 0x00]
      11. 6.6.11 DE_CTL Register (Sub-Address = 33) [reset = 0x00]
      12. 6.6.12 DE_TOP Register (Sub-Address = 34) [reset = 0x00]
      13. 6.6.13 DE_CNT Register (Sub-Address = 37–36) [reset = 0x0000]
      14. 6.6.14 DE_LIN Register (Sub-Address = 39–38) [reset = 0x0000]
      15. 6.6.15 H_RES Register (Sub-Address = 3B−3A)
      16. 6.6.16 V_RES Register (Sub-Address = 3D−3C)
  8. Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 Data and Control Signals
        2. 7.2.2.2 Configuration Options
        3. 7.2.2.3 Power Supplies Decoupling
      3. 7.2.3 Application Curves
    3. 7.3 Power Supply Recommendations
      1. 7.3.1 DVDD
      2. 7.3.2 TVDD
      3. 7.3.3 PVDD
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
        1. 7.4.1.1 Layer Stack
        2. 7.4.1.2 Routing High-Speed Differential Signal Traces (RxC-, RxC+, Rx0-, Rx0+, Rx1-, Rx1+, Rx2-, Rx2+)
        3. 7.4.1.3 DVI Connector
      2. 7.4.2 Layout Example
      3. 7.4.3 TI PowerPAD 64-Pin HTQFP Package
  9. Device and Documentation Support
    1. 8.1 Receiving Notification of Documentation Updates
    2. 8.2 Support Resources
    3. 8.3 Trademarks
    4. 8.4 Electrostatic Discharge Caution
    5. 8.5 Glossary
  10. Revision History
  11. 10Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • PAP|64
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Application Information

The TFP410 is a DVI-compliant digital transmitter that is used in digital host monitor systems to T.M.D.S. encode and serialize RGB pixel data streams. TFP410 supports resolutions from VGA to WUXGA (and 1080p). The host in a digital display system, usually a PC or consumer electronics device, contains a DVI-compatible transmitter such as the TI TFP410 that receives 24-bit pixel data along with appropriate control signals. The TFP410 encodes the signals into a high speed, low voltage, differential serial bit stream optimized for transmission over a twisted-pair cable to a display device such as the TFP401.