SLVSFI5A October   2020  – December 2020 TLC6C5748-Q1

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Terminal Configurations and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  7. 7 Parameter Measurement Information
    1. 7.1 Terminal-Equivalent Input and Output Schematic Diagrams
    2. 7.2 Test Circuits
    3. 7.3 Timing Diagrams
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Output Current Calculation
      2. 8.3.2 Register and Data Latch Configuration
        1. 8.3.2.1 769-Bit Common Shift Register
        2. 8.3.2.2 Grayscale (GS) Data Latch
        3. 8.3.2.3 Control Data Latch
        4. 8.3.2.4 Dot Correction (DC) Data Latch
        5. 8.3.2.5 Maximum Current (MC) Data Latch
        6. 8.3.2.6 Global Brightness Control (BC) Data Latch
        7. 8.3.2.7 Function Control (FC) Data Latch
      3. 8.3.3 Status Information Data (SID)
      4. 8.3.4 LED Open Detection (LOD)
      5. 8.3.5 LED Short Detection (LSD)
      6. 8.3.6 Thermal Shutdown Faults (TSD)
      7. 8.3.7 Noise Reduction
    4. 8.4 Device Functional Modes
      1. 8.4.1 Maximum Current Control (MC) Function
      2. 8.4.2 Dot Correction (DC) Function
      3. 8.4.3 Global Brightness Control (BC) Function
      4. 8.4.4 Grayscale (GS) Function (PWM Control)
        1. 8.4.4.1 Conventional PWM Control
        2. 8.4.4.2 Enhanced Spectrum (ES) PWM Control
        3. 8.4.4.3 Auto Display Repeat Function
        4. 8.4.4.4 Display Timing Reset Function
        5. 8.4.4.5 Auto Data Refresh Function
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Daisy-Chain Application
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Step-by-Step Design Procedure
          2. 9.2.1.2.2 Maximum Current (MC) Data
          3. 9.2.1.2.3 Global Brightness Control (BC) Data
          4. 9.2.1.2.4 Dot Correction (DC) Data
          5. 9.2.1.2.5 Grayscale (GS) Data
          6. 9.2.1.2.6 Other Control Data
        3. 9.2.1.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Receiving Notification of Documentation Updates
    2. 12.2 Support Resources
    3. 12.3 Trademarks
    4. 12.4 Electrostatic Discharge Caution
    5. 12.5 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.3.3 Status Information Data (SID)

The status information data (SID) contains the status of the LED open detection (LOD), LED short detection (LSD) and thermal shutdown faults(TSD). When the MSB of the common shift register is set to 0 and the RFRESH bit in the control data latch is 0, the SID are loaded to the common shift register at the LAT falling edge after the data in the common shift register are loaded to the grayscale data latch. If the common shift register MSB is 1, the SID are not loaded to the common shift register.

When the MSB of the common shift register is set to 0 and the RFRESH bit in the control data latch is 1, the SID are loaded to the common shift register at the GS counter 0000h just after LAT when the GS data are input. If the common shift register MSB is 1, the SID are not loaded to the common shift register. When the RFRESH bit is 1, the SCLK rising edge must be input with a low-level LAT signal after 65,538 GSCLKs (or more) are input from the LAT rising signal input.

After being loaded into the common shift register, new SID data cannot be loaded until at least one new bit of data is written into the common shift register. To recheck SID without changing the GS data, reprogram the common shift register with the same data currently programmed into the GS latch. When LAT goes high, the GS data do not change, but new SID data are loaded into the common shift register. LOD and LSD are shifted out of SOUT with each SCLK rising edge. The SID load configuration is shown in Figure 8-4 and Table 8-6.

GUID-8BF919E5-0202-4350-B238-CCCA5D2D968D-low.gifFigure 8-4 SID Load Configuration
Table 8-6 SID Load Description
COMMON SHIFT REGISTER BIT NUMBERLOADED SIDCOMMON SHIFT REGISTER BIT NUMBERLOADED SID
671-0No data loaded720OUTR0 LOD data
672OUTR0 LSD data
(0 = No error, 1 = Error)		721OUTG0 LOD data
673OUTG0 LSD data722OUTB0 LOD data
674OUTB0 LSD data723OUTR1 LOD data
675OUTR1 LSD data724OUTG1 LOD data
676OUTG1 LSD data725OUTB1 LOD data
677OUTB1 LSD data726OUTR2 LOD data
678OUTR2 LSD data727OUTG2 LOD data
679OUTG2 LSD data728OUTB2 LOD data
680OUTB2 LSD data729OUTR3 LOD data
681OUTR3 LSD data730OUTG3 LOD data
682OUTG3 LSD data731OUTB3 LOD data
683OUTB3 LSD data732OUTR4 LOD data
684OUTR4 LSD data733OUTG4 LOD data
685OUTG4 LSD data734OUTB4 LOD data
686OUTB4 LSD data735OUTR5 LOD data
687OUTR5 LSD data736OUTG5 LOD data
688OUTG5 LSD data737OUTB5 LOD data
689OUTB5 LSD data738OUTR6 LOD data
690OUTR6 LSD data739OUTG6 LOD data
691OUTG6 LSD data740OUTB6 LOD data
692OUTB6 LSD data741OUTR7 LOD data
693OUTR7 LSD data742OUTG7 LOD data
694OUTG7 LSD data743OUTB7 LOD data
695OUTB7 LSD data744OUTR8 LOD data
696OUTR8 LSD data745OUTG8 LOD data
697OUTG8 LSD data746OUTB8 LOD data
698OUTB8 LSD data747OUTR9 LOD data
699OUTR9 LSD data748OUTG9 LOD data
700OUTG9 LSD data749OUTB9 LOD data
701OUTB9 LSD data750OUTR10 LOD data
702OUTR10 LSD data751OUTG10 LOD data
703OUTG10 LSD data752OUTB10 LOD data
704OUTB10 LSD data753OUTR11 LOD data
705OUTR11 LSD data754OUTG11 LOD data
706OUTG11 LSD data755OUTB11 LOD data
707OUTB11 LSD data756OUTR12 LOD data
708OUTR12 LSD data757OUTG12 LOD data
709OUTG12 LSD data758OUTB12 LOD data
710OUTB12 LSD data759OUTR13 LOD data
711OUTR13 LSD data760OUTG13 LOD data
712OUTG13 LSD data761OUTB13 LOD data
713OUTB13 LSD data762OUTR14 LOD data
714OUTR14 LSD data763OUTG14 LOD data
715OUTG14 LSD data764OUTB14 LOD data
716OUTB14 LSD data765OUTR15 LOD data
717OUTR15 LSD data766OUTG15 LOD data
718OUTG15 LSD data767OUTB15 LOD data
719OUTB15 LSD data768No data loaded