JAJSOX0 March   2024 ADS127L18

ADVANCE INFORMATION  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Timing Diagrams
  7. 6 Parameter Measurement Information
    1. 6.1  Offset Error Measurement
    2. 6.2  Offset Drift Measurement
    3. 6.3  Gain Error Measurement
    4. 6.4  Gain Drift Measurement
    5. 6.5  NMRR Measurement
    6. 6.6  CMRR Measurement
    7. 6.7  PSRR Measurement
    8. 6.8  SNR Measurement
    9. 6.9  INL Error Measurement
    10. 6.10 THD Measurement
    11. 6.11 IMD Measurement
    12. 6.12 SFDR Measurement
    13. 6.13 Noise Performance
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Analog Inputs (AINP, AINN)
        1. 7.3.1.1 Input Range
      2. 7.3.2 Reference Voltage (REFP, REFN)
        1. 7.3.2.1 Reference Voltage Range
      3. 7.3.3 Clock Operation
        1. 7.3.3.1 Internal Oscillator
        2. 7.3.3.2 External Clock
      4. 7.3.4 Power Supplies
        1. 7.3.4.1 AVDD1 and AVSS
        2. 7.3.4.2 AVDD2
        3. 7.3.4.3 IOVDD
        4. 7.3.4.4 Power-On Reset (POR)
        5. 7.3.4.5 CAPA and CAPD
      5. 7.3.5 VCM Output Voltage
      6. 7.3.6 GPIO
      7. 7.3.7 Modulator
      8. 7.3.8 Digital Filter
        1. 7.3.8.1 Wideband Filter
      9. 7.3.9 Low-Latency Filter (Sinc)
        1. 7.3.9.1 Sinc4 Filter
        2. 7.3.9.2 Sinc4 + Sinc1 Cascade Filter
        3. 7.3.9.3 Sinc3 Filter
        4. 7.3.9.4 Sinc3 + Sinc1 Filter
    4. 7.4 Device Functional Modes
      1. 7.4.1  Speed Modes
      2. 7.4.2  Synchronization
        1. 7.4.2.1 Synchronized Control Mode
        2. 7.4.2.2 Start/Stop Control Mode
      3. 7.4.3  Digital Filter Settling
      4. 7.4.4  Conversion-Start Delay Time
      5. 7.4.5  Data Averaging
      6. 7.4.6  Calibration
        1. 7.4.6.1 Offset Calibration Registers
        2. 7.4.6.2 Gain Calibration Registers
        3. 7.4.6.3 Calibration Procedure
      7. 7.4.7  Reset
        1. 7.4.7.1 RESET Pin
        2. 7.4.7.2 Reset by SPI Register
        3. 7.4.7.3 Reset by SPI Input Pattern
      8. 7.4.8  Power-Down
      9. 7.4.9  Idle and Standby Modes
      10. 7.4.10 Diagnostics
        1. 7.4.10.1 ERROR Pin and ERR_FLAG Bit
        2. 7.4.10.2 Clock Counter
        3. 7.4.10.3 SCLK Counter
        4. 7.4.10.4 Frame-Sync CRC
        5. 7.4.10.5 SPI CRC
        6. 7.4.10.6 Register Map CRC
        7. 7.4.10.7 Self Test
      11. 7.4.11 Frame-Sync Data Port
        1. 7.4.11.1 FSYNC Pin
        2. 7.4.11.2 DCLK Pin
        3. 7.4.11.3 DOUTn Pins
        4. 7.4.11.4 DINn Pins
        5. 7.4.11.5 Time Division Multiplexing (TDM)
        6. 7.4.11.6 Data Size
        7. 7.4.11.7 STATUS_DP Header
        8. 7.4.11.8 Daisy Chain
        9. 7.4.11.9 Data Port Offset Timing
    5. 7.5 Programming
      1. 7.5.1 Hardware Programming
      2. 7.5.2 SPI Programming
        1. 7.5.2.1 Chip Select (CS)
        2. 7.5.2.2 Serial Clock (SCLK)
        3. 7.5.2.3 Serial Data Input (SDI)
        4. 7.5.2.4 Serial Data Output (SDO)
      3. 7.5.3 SPI Frame
      4. 7.5.4 SPI Commands
        1. 7.5.4.1 Read Register Command
        2. 7.5.4.2 Write Register Command
      5. 7.5.5 SPI Daisy-Chain
  9. 8 Register Map
  10. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Input Driver
      2. 9.1.2 Antialias Filter
      3. 9.1.3 Reference Voltage
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 ドキュメントの更新通知を受け取る方法
    3. 10.3 サポート・リソース
    4. 10.4 Trademarks
    5. 10.5 静電気放電に関する注意事項
    6. 10.6 用語集
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Mechanical Data

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

5.7 Switching Characteristics

1.65V ≤ IOVDD ≤ 1.9V, over operating ambient temperature range, OUT_DRV = 0b, CLOAD = 20pF (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
CLOCK
tC(CLK) ADC clock period 1, 2, 3, 4 or 8 / f(CLKIN) or f(OSC)
FRAME-SYNC DATA PORT
tc(FSYNC) FSYNC period 1 / f(DATA) ns
tw(FSYNCH) Pulse duration, FSYNC high 0.5 / f(DATA) ns
tw(FSYNCL) Pulse duration, FSYNC low 0.5 / f(DATA) ns
tp(FSDC) Propagation delay time, FSYNC rising edge to DCLK falling edge –1 1 ns
tc(DCLK) DCLK period 1, 2, 4, or 8 / f(CLKIN) or f(OSC) ns
tw(DCLKH) Pulse duration, DCLK low 0.5 x tC(DCLK) ns
tw(DCLKL) Pulse duration, DCLK high 0.5 x tC(DCLK) ns
th(DCDO) Hold time, DCLK falling edge to previous DOUT invalid -2 ns
tp(DCDO) Propagation delay time, DCLK falling edge to new DOUT valid 4 ns
SPI CONFIGURATION PORT
tp(CSDO) Propagation delay time, CS falling edge to SDO driven state 16 ns
tp(CSDOZ) Propagation delay time, CS rising edge to SDO tri-state 16 ns
th(SCDO) Hold time, SCLK rising edge to invalid SDO 3 ns
tp(SCDO) Propagation delay time, SCLK rising edge to valid SDO 20 ns
START PIN
tp(CLFS1) Propagation delay time, CLK falling edge after START rising edge to FSYNC and DCLK falling edge (conversion start) 0 4 ns
tp(CLFS2) Propagation delay time, CLK rising edge after START rising edge to FSYNC rising edge (first conversion ready) Unsettled data mode 1 / fDATA s
Settled data mode See the Digital Filter section
RESET PIN
tp(RSFS) Propagation delay time, RESET rising edge to FSYNC falling edge (ADC ready) 104 / f(CLK) ns