JAJSLT5A
january 2018 – may 2021
BQ25123
PRODUCTION DATA
1
1
特長
2
アプリケーション
3
概要
4
Revision History
5
Description (continued)
6
Device Comparison Table
7
Pin Configuration and Functions
8
Specifications
8.1
Absolute Maximum Ratings
8.2
ESD Ratings
8.3
Recommended Operating Conditions
8.4
Thermal Information
8.5
Electrical Characteristics
8.6
Timing Requirements
8.7
Typical Characteristics
9
Detailed Description
9.1
Overview
9.2
Functional Block Diagram
9.3
Feature Description
9.3.1
Ship Mode
9.3.1.1
Ship Mode Entry and Exit
9.3.2
High Impedance Mode
9.3.3
Active Battery Only Connected
9.3.4
Voltage Based Battery Monitor
9.3.5
Sleep Mode
9.3.6
Input Voltage Based Dynamic Power Management (VIN(DPM))
9.3.7
Input Overvoltage Protection and Undervoltage Status Indication
9.3.8
Battery Charging Process and Charge Profile
9.3.9
Dynamic Power Path Management Mode
9.3.10
Battery Supplement Mode
9.3.11
Default Mode
9.3.12
Termination and Pre-Charge Current Programming by External Components (IPRETERM)
9.3.13
Input Current Limit Programming by External Components (ILIM)
9.3.14
Charge Current Programming by External Components (ISET)
9.3.15
Safety Timer and Watchdog Timer
9.3.16
External NTC Monitoring (TS)
9.3.17
Thermal Protection
9.3.18
Typical Application Power Dissipation
9.3.19
Status Indicators ( PG and INT)
9.3.20
Chip Disable ( CD)
9.3.21
Buck (PWM) Output
9.3.22
Load Switch / LDO Output and Control
9.3.23
Manual Reset Timer and Reset Output ( MR and RESET)
9.4
Device Functional Modes
9.5
Programming
9.5.1
Serial Interface Description
9.5.2
F/S Mode Protocol
9.6
Register Maps
9.6.1
Status and Ship Mode Control Register
9.6.2
Faults and Faults Mask Register
9.6.3
TS Control and Faults Masks Register
9.6.4
Fast Charge Control Register
9.6.5
Termination/Pre-Charge and I2C Address Register
9.6.6
Battery Voltage Control Register
9.6.7
SYS VOUT Control Register
9.6.8
Load Switch and LDO Control Register
9.6.9
Push-Button Control Register
9.6.10
ILIM and Battery UVLO Control Register
9.6.11
Voltage Based Battery Monitor Register
9.6.12
VIN_DPM and Timers Register
10
Application and Implementation
10.1
Application Information
10.2
Typical Application
10.2.1
Design Requirements
10.2.2
Detailed Design Procedure
10.2.2.1
Default Settings
10.2.2.2
Choose the Correct Inductance and Capacitance
10.2.2.3
Calculations
10.2.2.3.1
Program the Fast Charge Current (ISET)
10.2.2.3.2
Program the Input Current Limit (ILIM)
10.2.2.3.3
Program the Pre-Charge/Termination Threshold (IPRETERM)
10.2.2.3.4
TS Resistors (TS)
10.2.3
Application Curves
10.2.3.1
Charger Curves
10.2.3.2
SYS Output Curves
10.2.3.3
Load Switch and LDO Curves
10.2.3.4
LS/LDO Output Curves
10.2.3.5
Timing Waveforms Curves
Power Supply Recommendations
11
Layout
11.1
Layout Guidelines
11.2
Layout Example
12
Device and Documentation Support
12.1
Device Support
12.1.1
サード・パーティ製品に関する免責事項
12.2
ドキュメントの更新通知を受け取る方法
12.3
サポート・リソース
12.4
Trademarks
12.5
静電気放電に関する注意事項
12.6
用語集
13
Mechanical, Packaging, and Orderable Information
パッケージ・オプション
メカニカル・データ(パッケージ|ピン)
YFP|25
MXBG084M
サーマルパッド・メカニカル・データ
発注情報
jajslt5a_oa
jajslt5a_pm
1
特長
1 回の充電あたりのシステム動作時間を増加
構成可能な 300mA 降圧レギュレータ
降圧コンバータがイネーブルの状態 (無負荷) での Iq:700nA (代表値)
負荷スイッチまたは 100mA LDO 出力を設定可能
最大 300mA の充電電流による高速充電
精度 0.5% のバッテリ電圧レギュレーション (3.6V~4.65V を 10mV 刻みで設定可能)
終端電流を最小 500µA に設定可能
シンプルな電圧ベースのバッテリ監視
占有面積が小さい高集積ソリューション
2.5mm × 2.5mm の WCSP パッケージと 6 個の外付け部品により、最小のソリューションを構築可能
押しボタンによる可変タイマ付きウェイクアップおよびリセット
システム電源およびバッテリ充電用の電力パス管理
電力パス管理により 50nA 未満のシップ・モードのバッテリ静止電流を実現し、保管寿命を延長
バッテリ充電器は 3.4V~5.5V
IN
で動作 (5.5V OVP / 20V 耐圧)
入力電流制限、充電電流、終端電流、ステータス出力用の専用ピン
I
2
C 通信制御
充電電圧および電流
終端スレッショルド
入力電流制限
VINDPM スレッショルド
タイマ・オプション
負荷スイッチ制御
フォルトとステータスのための割り込みの制御
システム出力電圧の調整
LDO 出力電圧を調整可能