JAJSFC0E December   2013  – January 2022 LMK00334

PRODUCTION DATA  

  1. 特長
  2. アプリケーション
  3. 概要
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements, Propagation Delay, and Output Skew
    7. 6.7 Typical Characteristics
  7. Parameter Measurement Information
    1. 7.1 Differential Voltage Measurement Terminology
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Crystal Power Dissipation vs. RLIM
      2. 8.3.2 Clock Inputs
      3. 8.3.3 Clock Outputs
        1. 8.3.3.1 Reference Output
    4. 8.4 Device Functional Modes
      1. 8.4.1 VCC and VCCO Power Supplies
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Driving the Clock Inputs
        2. 9.2.1.2 Crystal Interface
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Termination and Use of Clock Drivers
        2. 9.2.2.2 Termination for DC-Coupled Differential Operation
        3. 9.2.2.3 Termination for AC-Coupled Differential Operation
      3. 9.2.3 Application Curve
  10. 10Power Supply Recommendations
    1. 10.1 Current Consumption and Power Dissipation Calculations
      1. 10.1.1 Power Dissipation Example: Worst-Case Dissipation
    2. 10.2 Power Supply Bypassing
      1. 10.2.1 Power Supply Ripple Rejection
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
    3. 11.3 Thermal Management
  12. 12Device and Documentation Support
    1. 12.1 Documentation Support
      1. 12.1.1 Related Documentation
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 サポート・リソース
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ(パッケージ|ピン)
サーマルパッド・メカニカル・データ
発注情報

Current Consumption and Power Dissipation Calculations

The current consumption values specified in Section 6.5 can be used to calculate the total power dissipation and IC power dissipation for any device configuration. The total VCC core supply current (ICC_TOTAL) can be calculated using Equation 5:

Equation 5. ICC_TOTAL = ICC_CORE + ICC_BANKS + ICC_CMOS

where

  • ICC_CORE is the VCC current for core logic and input blocks and depends on selected input (CLKinX or OSCin).
  • ICC_HCSL is the VCC current for Banks A and B
  • ICC_CMOS is the VCC current for the LVCMOS output (or 0 mA if REFout is disabled).

Because the output supplies (VCCOA, VCCOB, VCCOC) can be powered from three independent voltages, the respective output supply currents (ICCO_BANK_A, ICCO_BANK_B, and ICCO_CMOS) should be calculated separately.

ICCO_BANK for either Bank A or B may be taken as 50% of the corresponding output supply current specified for two banks (ICCO_HCSL) provided the output loading matches the specified conditions. Otherwise, ICCO_BANK should be calculated per bank as shown in Equation 6:

Equation 6. ICCO_BANK = IBANK_BIAS + (N × IOUT_LOAD)

where

  • IBANK_BIAS is the output bank bias current (fixed value).
  • IOUT_LOAD is the DC load current per loaded output pair.
  • N is the number of loaded output pairs (N = 0 to 2).

Table 10-1 shows the typical IBANK_BIAS values and IOUT_LOAD expressions for HCSL.

Table 10-1 Typical Output Bank Bias and Load Currents
CURRENT PARAMETERHCSL
IBANK_BIAS2.4 mA
IOUT_LOADVOH/RT

Once the current consumption is known for each supply, the total power dissipation (PTOTAL) can be calculated by Equation 7:

Equation 7. PTOTAL = (VCC × ICC_TOTAL) + (VCCOA × ICCO_BANK) + (VCCOB × ICCO_BANK) + (VCCOC × ICCO_CMOS)

If the device is configured with HCSL outputs, then it is also necessary to calculate the power dissipated in any termination resistors (PRT_HCSL). The external power dissipation values can be calculated by Equation 8:

Equation 8. PRT_HCSL (per HCSL pair) = VOH2 / RT

Finally, the IC power dissipation (PDEVICE) can be computed by subtracting the external power dissipation values from PTOTAL as shown in Equation 9:

Equation 9. PDEVICE = PTOTAL – N × PRT_HCSL

where

  • N is the number of HCSL output pairs with termination resistors to GND.