JAJSR90 September   2023 LMQ644A2-Q1

PRODMIX  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
    1. 6.1 Wettable Flanks
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Input Voltage Range (VIN)
      2. 8.3.2  Enable EN Pin and Use as VIN UVLO
      3. 8.3.3  Output Voltage Selection and Soft Start
      4. 8.3.4  SYNC Allows Clock Synchronization and Mode Selection
      5. 8.3.5  Clock Locking
      6. 8.3.6  Adjustable Switching Frequency
      7. 8.3.7  Power-Good Output Voltage Monitoring
      8. 8.3.8  Internal LDO, VCC UVLO, and BIAS Input
      9. 8.3.9  Bootstrap Voltage and VCBOOT-UVLO (CB1 and CB2 Pin)
      10. 8.3.10 CONFIG Device Configuration Pin
      11. 8.3.11 Spread Spectrum
      12. 8.3.12 Soft Start and Recovery From Dropout
      13. 8.3.13 Overcurrent and Short-Circuit Protection
      14. 8.3.14 Hiccup
      15. 8.3.15 Thermal Shutdown
    4. 8.4 Device Functional Modes
      1. 8.4.1 Shutdown Mode
      2. 8.4.2 Standby Mode
      3. 8.4.3 Active Mode
        1. 8.4.3.1 Peak Current Mode Operation
        2. 8.4.3.2 Auto Mode Operation
          1. 8.4.3.2.1 Diode Emulation
        3. 8.4.3.3 FPWM Mode Operation
        4. 8.4.3.4 Minimum On-time (High Input Voltage) Operation
        5. 8.4.3.5 Dropout
        6. 8.4.3.6 Recovery from Dropout
        7. 8.4.3.7 Other Fault Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1  Choosing the Switching Frequency
        2. 9.2.2.2  Setting the Output Voltage
        3. 9.2.2.3  Inductor Selection
        4. 9.2.2.4  Output Capacitor Selection
        5. 9.2.2.5  Input Capacitor Selection
        6. 9.2.2.6  BOOT Capacitor
        7. 9.2.2.7  VCC
        8. 9.2.2.8  CFF and RFF Selection
        9. 9.2.2.9  SYNCHRONIZATION AND MODE
        10. 9.2.2.10 External UVLO
        11. 9.2.2.11 Typical Thermal Performance
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
        1. 9.4.1.1 Ground and Thermal Considerations
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 サード・パーティ製品に関する免責事項
    2. 10.2 ドキュメントの更新通知を受け取る方法
    3. 10.3 サポート・リソース
    4. 10.4 Trademarks
    5. 10.5 用語集
    6. 10.6 静電気放電に関する注意事項
  12. 11Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.4.3 Active Mode

The device is in active mode when the following occurs:

  • The EN pin is above VEN.
  • VIN is above VEN.
  • VIN is high enough to satisfy the VIN minimum operating input voltage.
  • No other fault conditions are present.
See Section 8.3 for protection features. The simplest way to enable the operation is to connect EN to VIN, allowing self-start-up when the applied input voltage exceeds the minimum VIN_OPERATE.

In active mode, depending on the load current, input voltage, and output voltage, the LMQ644xx is in one of six sub-modes:

  • Continuous conduction mode (CCM) with fixed switching frequency and peak current mode operation
  • Discontinuous conduction mode (DCM) while in auto mode when the load current is lower than half of the inductor current ripple. If current continues to reduce, the device enters Pulse Frequency Modulation (PFM) which reduces the switch frequency to maintain regulation while reducing switching losses to achieve higher efficiency at light load.
  • Minimum on-time operation while the on-time of the device needed for full-frequency operation at the requested low-duty cycle is not supported by TON_MIN
  • Forced pulse width modulation (FPWM) similar to CCM with fixed-switching frequency, but extends the fixed frequency range of operation from full to no load
  • Dropout mode when switching frequency is reduced to minimize dropout
  • Recovery from dropout similar to other modes of operation except the output voltage setpoint is gradually moved up until the programmed setpoint is reached.