JAJSNB3 September   2023 LP5813

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 Device Comparison
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
  9. 8 Typical Characteristics
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Synchronous Boost Converter
        1. 9.3.1.1 Undervoltage Lockout
        2. 9.3.1.2 Enable and Soft Start
        3. 9.3.1.3 Switching Frequency
        4. 9.3.1.4 Current Limit Operation
        5. 9.3.1.5 Boost PWM Mode
        6. 9.3.1.6 Boost PFM Mode
        7. 9.3.1.7 Pass-Through Mode
      2. 9.3.2 Time-cross-multiplexing (TCM) scheme
        1. 9.3.2.1 Direct drive mode
        2. 9.3.2.2 TCM drive mode
        3. 9.3.2.3 Mix drive mode
        4. 9.3.2.4 Ghosting elimination
      3. 9.3.3 Analog Dimming
      4. 9.3.4 PWM Dimming
      5. 9.3.5 Autonomous Animation Engine Control
        1. 9.3.5.1 Animation Engine Pattern
        2. 9.3.5.2 Sloper
        3. 9.3.5.3 Animation Engine Unit (AEU)
        4. 9.3.5.4 Animation Pause Unit (APU)
      6. 9.3.6 Protections and Diagnostics
        1. 9.3.6.1 Overvoltage Protection
        2. 9.3.6.2 Output Short-to-Ground Protection
        3. 9.3.6.3 LED Open Detections
        4. 9.3.6.4 LED Short Detections
        5. 9.3.6.5 Thermal Shutdown
    4. 9.4 Device Functional Modes
    5. 9.5 Programming
    6. 9.6 Register Map Table
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Application
      2. 10.2.2 Design Parameters
      3. 10.2.3 Detailed Design Procedure
        1. 10.2.3.1 Inductor Selection
        2. 10.2.3.2 Output Capacitor Selection
        3. 10.2.3.3 Input Capacitor Selection
        4. 10.2.3.4 Program Procedure
        5. 10.2.3.5 Programming Example
      4. 10.2.4 Application Performance Plots
    3. 10.3 Power Supply Recommendations
    4. 10.4 Layout
      1. 10.4.1 Layout Guidelines
      2. 10.4.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Documentation Support
    2. 11.2 ドキュメントの更新通知を受け取る方法
    3. 11.3 サポート・リソース
    4. 11.4 Trademarks
    5. 11.5 静電気放電に関する注意事項
    6. 11.6 用語集
  13. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

9.3.5.4 Animation Pause Unit (APU)

The APU is defined as the pausing time at the beginning and the end of the animation pattern. The APU contains 1 time value which is selectable from 0 to 8 s with 16 levels referring to Table 9-4. If the value is set as 0, the APU is skipped. The brightness of APU1 uses the PWM1 value of the AEU following the APU1, while the brightness of APU2 uses the PWM5 value of the AEU in front of APU2. One animation pattern example is shown in Figure 9-20. Only AEU2 is enabled in the pattern, so that the brightness of APU1 uses the PWM1 value of AEU2, and the brightness of APU2 uses PWM5 value of AEU2.

GUID-20220622-SS0I-RHK7-MPQX-CPGJX12MDNZG-low.svg Figure 9-20 APU example