JAJS234H MARCH   2007  – May 2019 TPS40192 , TPS40193

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      アプリケーション概略図
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Dissipation Ratings
    7. 7.7 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Voltage Reference
      2. 8.3.2  Oscillator
      3. 8.3.3  UVLO
      4. 8.3.4  Enable Functionality
      5. 8.3.5  Start-Up Sequence and Timing
      6. 8.3.6  Selecting the Short Circuit Current
      7. 8.3.7  5-V Regulator
      8. 8.3.8  Prebias Start-Up
      9. 8.3.9  Drivers
      10. 8.3.10 Power Good
      11. 8.3.11 Thermal Shutdown
    4. 8.4 Device Functional Modes
      1. 8.4.1 Continuous Conduction Mode
      2. 8.4.2 Low-Quiescent Shutdown
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1  Selecting the Switching Frequency
        2. 9.2.2.2  Inductor Selection
        3. 9.2.2.3  Output Capacitor Selection (C8)
        4. 9.2.2.4  Peak Current Rating of the Inductor
        5. 9.2.2.5  Input Capacitor Selection (C7)
        6. 9.2.2.6  MOSFET Switch Selection (Q1, Q2)
        7. 9.2.2.7  Boot Strap Capacitor
        8. 9.2.2.8  Input Bypass Capacitor (C6)
        9. 9.2.2.9  BP5 Bypass Capacitor (C5)
        10. 9.2.2.10 Input Voltage Filter Resistor (R11)
        11. 9.2.2.11 Short Circuit Protection (R9)
        12. 9.2.2.12 Feedback Compensation (Modeling the Power Stage)
        13. 9.2.2.13 Feedback Divider (R7, R8)
        14. 9.2.2.14 Error Amplifier Compensation (R6, R10, C1, C2, C3)
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Examples
  12. 12デバイスおよびドキュメントのサポート
    1. 12.1 デバイス・サポート
      1. 12.1.1 開発サポート
        1. 12.1.1.1 関連デバイス
      2. 12.1.2 デバイスの項目表記
    2. 12.2 ドキュメントのサポート
    3. 12.3 関連リンク
    4. 12.4 ドキュメントの更新通知を受け取る方法
    5. 12.5 コミュニティ・リソース
    6. 12.6 商標
    7. 12.7 静電気放電に関する注意事項
    8. 12.8 Glossary
  13. 13メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.3.10 Power Good

The TPS40192 and TPS40193 devices provides an indication that output power is good for the converter. This is an open drain signal and pulls low when any condition exists that would indicate that the output of the supply might be out of regulation. These conditions include:

  • VFB is more than ±10% from nominal
  • soft-start is active
  • an undervoltage condition exists for the device
  • a short circuit condition has been detected
  • die temperature is over (145°C)

NOTE

When there is no power to the device, PGOOD is not able to pull close to GND if an auxiliary supply is used for the power good indication. In this case, a built in resistor connected from drain to gate on the PGOOD pull down device makes the PGOOD pin look approximately like a diode to GND.