JAJSFE5C October   2009  – May 2018 TPS65720 , TPS65721

PRODUCTION DATA.  

  1. 特長
  2. アプリケーション
  3. 概要
    1.     代表的なアプリケーションの回路図
  4. 改訂履歴
  5. 概要(続き)
  6. Device Options
  7. Pin Configuration and Functions
    1.     Pin Functions—DSBGA (TPS65720)
    2.     Pin Functions—DSBGA (TPS657201, TPS657202)
    3.     Pin Functions—WQFN (TPS65721)
  8. Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Dissipation Ratings
    7. 8.7 Timing Requirements
    8. 8.8 Switching Characteristics
    9. 8.9 Typical Characteristics
  9. Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagrams
    3. 9.3 Feature Description
      1. 9.3.1  Battery Charger and Power Path
      2. 9.3.2  Power-Path Management
      3. 9.3.3  Battery Charging
        1. 9.3.3.1 I-PRECHARGE
        2. 9.3.3.2 ITERM
        3. 9.3.3.3 Battery Detection and Recharge
        4. 9.3.3.4 Charge Termination On/Off
        5. 9.3.3.5 Timers
        6. 9.3.3.6 Dynamic Timer Function
        7. 9.3.3.7 Charger Fault
      4. 9.3.4  Thermal Regulation and Thermal Shutdown
      5. 9.3.5  Battery Pack Temperature Monitoring
      6. 9.3.6  DCDC1 Converter
      7. 9.3.7  Power Save Mode
        1. 9.3.7.1 Dynamic Voltage Positioning
        2. 9.3.7.2 Soft Start
        3. 9.3.7.3 100% Duty Cycle Low Dropout Operation
        4. 9.3.7.4 Undervoltage Lockout
      8. 9.3.8  Short-Circuit Protection
      9. 9.3.9  Thermal Shutdown
      10. 9.3.10 LDO1
        1. 9.3.10.1 Default Voltage Setting for LDOs and DCDC1
        2. 9.3.10.2 Internal Analog Multiplexer (BAT, TS, TS_OUT); TPS657201, TPS657202 Only
        3. 9.3.10.3 Internal Battery Voltage Comparator
        4. 9.3.10.4 GPIOs, LED Drivers
        5. 9.3.10.5 RESET Output
        6. 9.3.10.6 Threshold Input (TPS65721 Only)
          1. 9.3.10.6.1 ENABLE for DCDC1 and LDO1
          2. 9.3.10.6.2 PB_IN Input
          3. 9.3.10.6.3 HOLD_DCDC1 Input
          4. 9.3.10.6.4 HOLD_LDO1 Input
          5. 9.3.10.6.5 INT Output
    4. 9.4 Device Functional Modes
      1. 9.4.1 Power Down
      2. 9.4.2 Sleep Mode
      3. 9.4.3 Standby Mode
      4. 9.4.4 Power-On Reset Mode
      5. 9.4.5 Idle Mode
    5. 9.5 Programming
      1. 9.5.1 Serial Interface
    6. 9.6 Register Maps
      1. 9.6.1  CHGSTATUS Register Address: 01h (read only)
      2. 9.6.2  CHGCONFIG0 Register Address: 02h (read/write)
      3. 9.6.3  CHGCONFIG1 Register Address: 03h (read/write)
      4. 9.6.4  CHGCONFIG2 Register Address: 04h (read/write)
      5. 9.6.5  CHGCONFIG3 Register Address: 05h (read/write)
      6. 9.6.6  CHGSTATE Register Address: 06h (read only)
      7. 9.6.7  DEFDCDC1 Register Address: 07h (read/write)
      8. 9.6.8  LDO_CTRL Register Address: 08h (read/write)
      9. 9.6.9  CONTROL0 Register Address: 09h (read/write)
      10. 9.6.10 CONTROL1 Register Address: 0Ah (read/write)
      11. 9.6.11 GPIO_SSC Register Address: 0Bh (read/write)
      12. 9.6.12 GPIODIR Register Address: 0Ch (read/write)
      13. 9.6.13 IRMASK0 Register Address: 0Dh (read/write)
      14. 9.6.14 IRMASK1 Register Address: 0Eh (read/write)
      15. 9.6.15 IRMASK2 Register Address: 0Fh (read/write)
      16. 9.6.16 IR0 Register Address: 10h (read only)
      17. 9.6.17 IR1 Register Address: 11h (read)
      18. 9.6.18 IR2 Register Address: 12h (read)
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Output Voltage Setting
          1. 10.2.2.1.1 DCDC1
          2. 10.2.2.1.2 LDO1
        2. 10.2.2.2 Output Filter Design (Inductor and Output Capacitor)
          1. 10.2.2.2.1 Inductor Selection
          2. 10.2.2.2.2 Output Capacitor Selection
          3. 10.2.2.2.3 Input Capacitor Selection
        3. 10.2.2.3 Charger/Power Path
          1. 10.2.2.3.1 Charger Stability
          2. 10.2.2.3.2 Setting the Charge Current
          3. 10.2.2.3.3 Dynamic Power Path Management (DPPM)
      3. 10.2.3 Application Curves
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13デバイスおよびドキュメントのサポート
    1. 13.1 デバイス・サポート
      1. 13.1.1 デベロッパー・ネットワークの製品に関する免責事項
    2. 13.2 ドキュメントのサポート
      1. 13.2.1 関連資料
    3. 13.3 関連リンク
    4. 13.4 ドキュメントの更新通知を受け取る方法
    5. 13.5 コミュニティ・リソース
    6. 13.6 商標
    7. 13.7 静電気放電に関する注意事項
    8. 13.8 Glossary
  14. 14メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ(パッケージ|ピン)
サーマルパッド・メカニカル・データ
発注情報

Pin Configuration and Functions

YFF Package
25-Pin DSBGA
Bottom View
TPS65720 TPS657201 TPS657202 TPS65721 po_lvs979.gif

Pin Functions—DSBGA (TPS65720)

PIN I/O DESCRIPTION
NO. NAME
A1 VLDO1 O Output voltage of LDO1
A2 HOLD_LDO1 I Power-on input for LDO1. When pulled HIGH, LDO1 is kept enabled after PB_IN was released HIGH.
A3 GPIO3 I/O General purpose I/O or 5-mA current sink
A4 GPIO1 I/O General purpose I/O
A5 SCLK I Clock input for the I2C interface
B1 VINLDO1 I Input voltage for LDO1
B2 GND Connect to AGND and PGND
B3 GPIO2 I/O General purpose I/O or 5-mA current sink
B4 GPIO0 I/O General purpose I/O
B5 SDAT I/O Data line for the I2C interface
C1 AGND Analog ground
C2 TS I Connect a thermistor from this pin to GND for battery temperature
C3 INT O Open-drain interrupt output
C4 PB_IN I Push button input; Turns on DCDC1 and LDO1 if pulled to GND.
C5 RESET O Open-drain output of the reset generator; This output goes active LOW when the output voltage of LDO1 falls 8% below its target voltage.
D1 FB_DCDC1 I Feedback input of step-down converter
D2 HOLD_DCDC1 I Power-On input for DCDC1 converter. When pulled HIGH, the DC-DC converter is kept enabled after PB_IN was released HIGH.
D3 BAT I/O Connect to battery + terminal
D4 SYS O System voltage; output of the power path manager. Power input for step-down converter DCDC1
D5 ISET I Connect a resistor from this pin to GND to set fast charge current
E1 PGND Power ground
E2 L1 O Switch output of step-down converter
E3 BAT I/O Connect to battery + terminal
E4 SYS O System voltage; output of the power path manager. Power input for step-down converter DCDC1
E5 AC I Input power for power manager, connect to external DC supply.
YFF Package
25-Pin DSBGA
Bottom View
TPS65720 TPS657201 TPS657202 TPS65721 po3_lvs979.gif

Pin Functions—DSBGA (TPS657201, TPS657202)

PIN I/O DESCRIPTION
NO. NAME
A1 VLDO1 O Output voltage of LDO1
A2 HOLD_LDO1 I Power-on input for LDO1. When pulled HIGH, LDO1 is kept enabled after PB_IN was released HIGH.
A3 GPIO3 I/O General purpose I/O or 5-mA current sink
A4 GPIO1 I/O General purpose I/O
A5 SCLK I Clock input for the I2C interface
B1 VINLDO1 I Input voltage for LDO1
B2 VBAT/TS_OUT O Output of battery temperature and battery voltage monitor
B3 GPIO2 I/O General purpose I/O or 5-mA current sink
B4 GPIO0 I/O General purpose I/O
B5 SDAT I/O Data line for the I2C interface
C1 AGND Analog ground
C2 TS I Connect a thermistor from this pin to GND for battery temperature
C3 INT O Open-drain interrupt output
C4 PB_IN I Push button input; Turns on DCDC1 and LDO1 if pulled to GND.
C5 RESET O Open-drain output of the reset generator; This output goes active LOW when the output voltage of LDO1 falls 8% below its target voltage.
D1 FB_DCDC1 I Feedback input of step-down converter
D2 HOLD_DCDC1 I Power-on input for DCDC1 converter. When pulled HIGH, the DC-DC converter is kept enabled after PB_IN was released HIGH.
D3 BAT I/O Connect to battery + terminal
D4 SYS O System voltage; output of the power path manager. Power input for step-down converter DCDC1
D5 ISET I Connect a resistor from this pin to GND to set fast charge current
E1 PGND Power ground
E2 L1 O Switch output of step-down converter
E3 BAT I/O Connect to battery + terminal
E4 SYS O System voltage; output of the power path manager. Power input for step-down converter DCDC1
E5 AC I Input power for power manager, connect to external DC supply.
RSN Package
32-Pin WQFN With Thermal Pad
Top View
TPS65720 TPS657201 TPS657202 TPS65721 po2_lvs979.gif

Pin Functions—WQFN (TPS65721)

PIN I/O DESCRIPTION
NAME NO.
AC 17, 18 I Input power for power manager, connect to external DC supply.
AGND 28 Analog ground
BAT 21, 22 I/O Connect to battery + terminal
FB_DCDC1 26 I Feedback input of step-down converter
FB_LDO1 1 I Feedback input for LDO1
GND 29 Connect to AGND and PGND
GPIO0 7 I/O General purpose I/O
GPIO1 6 I/O General purpose I/O
GPIO2 5 I/O General purpose I/O or 5-mA current source
GPIO3 4 I/O General purpose I/O or 5-mA current source
HOLD_DCDC1 25 I Power-on input for DCDC1 converter. When pulled HIGH, the DC-DC converter is kept enabled after PB_IN was released HIGH.
HOLD_LDO1 2 I Power-on input for LDO1. When pulled HIGH, LDO1 is kept enabled after PB_IN was released HIGH.
INT 13 O Open-drain interrupt output
ISET 16 I Connect a resistor from this pin to GND to set fast charge current
L1 23 O Switch output of step-down converter
MODE 11 I Pull HIGH to force the DCDC1 converter to PWM mode.
PB_IN 15 I Push button input; Turns on DCDC1 and LDO1 if pulled to GND.
PGND 24 Power ground
RESET 14 O Open-drain output of the reset generator; This output goes active LOW when the input voltage at pin THRESHOLD falls below the threshold voltage.
SCLK 8 I Clock input for the I2C interface
SDAT 12 I/O Data line for the I2C interface
SYS 19, 20 O System voltage; output of the power path manager. Power input for step-down converter DCDC1
THRESHOLD 3 I Input voltage to the reset comparator. When the input voltage falls below the threshold, the RESET output is actively pulled LOW.
TS 27 I Connect a thermistor from this pin to GND for battery temperature
VINLDO1 30 I Input voltage for LDO1
VLDO1 31 O Output voltage from LDO1
ThermalPad Connect to GND