JAJSC12D October   2013  – April 2018

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      可変出力オプション
      2.      固定出力オプション
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Device Comparison
  7. 7 Pin Configuration and Functions
    1.     Pin Functions
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Timing Requirements
    7. 8.7 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagrams
    3. 9.3 Feature Description
      1. 9.3.1 Enable (EN)
      2. 9.3.2 Regulated Output (VOUT)
      3. 9.3.3 Power-On-Reset (RESET)
      4. 9.3.4 Reset Delay Timer (DELAY)
      5. 9.3.5 Adjustable Output Voltage (ADJ for TPS7B6701)
      6. 9.3.6 Undervoltage Shutdown
      7. 9.3.7 Thermal Shutdown
      8. 9.3.8 Thermal Protection
    4. 9.4 Device Functional Modes
      1. 9.4.1 Operation With VIN < 4 V
      2. 9.4.2 Operation With EN Control
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Power Dissipation and Thermal Considerations
      3. 10.2.3 Application Curves
  11. 11Power Supply Recommendations
    1. 11.1 Dropout Recovery
      1. 11.1.1 LDO Dropout Recovery Explained
      2. 11.1.2 TPS7B67xx-Q1 Dropout During Startup
  12. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 Enhanced Thermal Pad
      2. 12.1.2 Package Mounting
      3. 12.1.3 Board Layout Recommendations to Improve PSRR and Noise Performance
      4. 12.1.4 Additional Layout Considerations
    2. 12.2 Layout Example
  13. 13デバイスおよびドキュメントのサポート
    1. 13.1 関連リンク
    2. 13.2 ドキュメントの更新通知を受け取る方法
    3. 13.3 コミュニティ・リソース
    4. 13.4 商標
    5. 13.5 静電気放電に関する注意事項
    6. 13.6 Glossary
  14. 14メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

12.1.3 Board Layout Recommendations to Improve PSRR and Noise Performance

  • To improve AC performance such as PSRR, output noise, and transient response, TI recommends to design the board with separate ground planes for VIN and VOUT, with each ground plane connected only at the GND pin of the device. In addition, the ground connection for the output capacitor must connect directly to the GND pin of the device.
  • Equivalent series inductance (ESL) and ESR must be minimized in order to maximize performance and ensure stability. Every capacitor must be placed as close to the device as possible and on the same side of the PCB as the regulator.
  • Do not place any of the capacitors on the opposite side of the PCB from where the regulator is installed. The use of vias and long traces is strongly discouraged because of the negative impact on system performance. Vias and long traces can also cause instability.
  • If possible, and to ensure the maximum performance listed in this data sheet, use the same layout pattern used for TPS7B67xx-Q1 evaluation board, available at www.ti.com.