4 改訂履歴
Changes from C Revision (December 2014) to D Revision
- Added Dropout Recovery section explaining LDO behavior when exiting dropout Go
Changes from B Revision (March 2014) to C Revision
- Deleted TPS7B6750A-Q1およびTPS7B6750B-Q1デバイスとDDPAKパッケージをデータシートからGo
- Changed the word terminal to pin throughout the data sheetGo
- Changed the Handling Ratings table to ESD Ratings and moved the storage temperature into the Absolute Maximum Ratings table. Added corner pin values for CDM ratings. Go
Changes from A Revision (November 2013) to B Revision
- 表紙を更新し、以下の記述を追加: 「製品情報」表、デバイスのファミリ名をドキュメントのタイトルに追加、ナビゲーション・ボタンを追加Go
- Changed 「特長」リストで、EN = LOWのときのIQの値を2未満から4未満へGo
- Added 「改訂履歴」を2ページへ移動、「目次」をGo
- Replaced the ORDERING INFORMATION table with the Device Comparison Table and deleted the Device and Package columnsGo
- Added Moved all electrical specifications tables and the Typical Characteristics section into the Specifications sectionGo
- Changed the max value for DELAY from VI to 45 V in the Absolute Maximum Ratings table. Also added new table note for DELAYGo
- Changed the max value for ADJ, RESET from VO to 22 V in the Absolute Maximum Ratings tableGo
- Changed the value of IO from 1 mA to 450 mA for the Input voltage test conditions in the Electrical Characteristics tableGo
- Added the value for VI in the test conditions of the Regulated output and the Line regulator parameters in the Electrical Characteristics table Go
- Moved the timing parameters (TIMING FOR RESET) out of the Electrical Characteristics table and into the new Timing Requirements table Go
- Added the Overview section title to the first paragraph of the Detailed Description section Go
- Updated the Power-On_Reset (RESET) section by making the following changes: changed the percentage that VO exceeds for the reset output to change from 90% to 91.6% (also changed this value in the Reset Delay Timer (DELAY) section), removed The on-chip oscillator presets the delay, and changed the percentage level to assert the output from 90% to 89.6%Go
- Changed the junction temperature value that disables thermal protection from 170°C to 175°C in the Thermal Protection sectionGo
- Added the Device Functional Modes section Go
- Added the Typical Application section in the new Applications and Implementation section Go
- Added the Power Supply Recommendations section Go
- Changed the LAYOUT INFORMATION section to the Layout section and added the Layout Example sectionGo
- Added 「メカニカル、パッケージ、および注文情報」セクション。また、「デバイスおよびドキュメントのサポート」セクションを追加し、商標情報と「静電放電に関する注意事項」を記載。このセクションには、新たにTI用語集への参照も記載Go
Changes from * Revision (October 2013) to A Revision
- Changed 「特長」リストで最大ドロップアウト電圧を500mVから450mVへGo
- Added 「アプリケーション」リストに車体制御モジュールをGo
- Changed 可変出力と固定出力のオプションの相違を示すため、代表的なアプリケーションの回路図をGo
- Changed 「概要」セクションで低電圧トラッキング機能のテキストをイネーブル機能のテキストにGo
- Changed ドキュメントのステータスを製品プレビューから量産データへGo
- Changed the MIN value for RESET and ADJ in the RECOMMENDED OPERATING CONDITIONS table from 0 to 1.5 and removed low voltage parameter for those pinsGo
- Added Added board dimensions to the high K profile THERMAL INFORMATION table noteGo
- Changed test condition for the input voltage to fixed 3.3-V output and added 5-V and two adjustable output conditionsGo
- Changed max value for the line regulation parameter from 2 to 10Go
- Changed TYP value for dropout voltage where IO = 400 mA from 240 to 260Go
- Changed TYP value for dropout voltage where IO = 200 mA from 160 to 150Go
- Changed Output current-limit typ value to max value for VOUT short to groundGo
- Deleted VIN condition from test condition for PSRRGo
- Added TYPICAL CHARACTERISTICS sectionGo
- Added the DETAILED DESCRIPTION sectionGo
- Added block diagram fro the TPS7B6733-Q1 and TPS7B6750-Q1Go
- Added the APPLICATION INFORMATION sectionGo
- Added the LAYOUT INFORMATION sectionGo