SLAU928A May   2024  – September 2025 MSPM0L1227 , MSPM0L1227-Q1 , MSPM0L1228 , MSPM0L1228-Q1 , MSPM0L2227 , MSPM0L2227-Q1 , MSPM0L2228 , MSPM0L2228-Q1

 

  1.   1
  2.   Description
  3.   Get Started
  4.   Features
  5.   Applications
  6.   6
  7. 1Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Kit Contents
    3. 1.3 Specification
    4. 1.4 Device Information
  8. 2Hardware
    1. 2.1 Hardware Overview
    2. 2.2 Power Requirements
    3. 2.3 XDS110 Debug Probe
      1. 2.3.1 Isolation Jumper Block
      2. 2.3.2 Application (Backchannel) UART
    4. 2.4 Measure Current Draw of the MSPM0L2228
    5. 2.5 Clocking
    6. 2.6 BoosterPack Plug-in Module Pinout
    7. 2.7 Liquid Crystal Display (LCD)
    8. 2.8 SuperCap
  9. 3Software
    1. 3.1 Software Development Options
    2. 3.2 CCS Cloud
  10. 4Hardware Design Files
    1. 4.1 Schematics
    2. 4.2 PCB Layers
    3. 4.3 Bill of Materials (BOM)
  11. 5Additional Information
    1. 5.1 Trademarks
  12. 6Related Documentation
    1. 6.1 Supplemental Content
  13. 7Revision History

2.1 Hardware Overview

LP-MSPM0L2228 Diagram of LP-MSPM0L2228 Jumpers and Connectors Figure 2-1 Diagram of LP-MSPM0L2228 Jumpers and Connectors

LP-MSPM0L2228 has many hardware features, which allow the user full access to the MSPM0L2228 pins, while still providing onboard connectivity for easy use. Shunt connections provide a way for the user to easily change LaunchPad configuration. The location of these shunts is shown in Figure 2-1. The connection of each shunt is described in Table 2-1.

Table 2-1 Jumper Information
Jumper Description Default Setting Connected Signal
J7 Open Drain IO Pull-ups Right and center connection PA0: 4.7k pull-up resistor to 5V or 2.2k pull-up resistor to 3.3V depending on setting
J8 Open Drain IO Pull-ups Right and center connection PA1: 4.7kΩ pull-up resistor to 5V or 2.2kΩ pull-up resistor to 3.3V depending on setting
J9 Red LED Connection (LED3) Populated 3.3V through LED and 470Ω resistor to PA0
J10 RGB Blue Connection Populated PA23 through 220Ω resistor and LED to ground.
J11 RGB Red Connection Populated PB10 through 220Ω resistor and LED to ground
J12 RGB Green Connection Populated PB9 through 220Ω resistor and LED to ground
J13 PB3/TIO Connection Center and bottom connection PB3 boosterpack to PB3 pin and TamperIO
J14 PB2/TIO Connection Center and bottom connection PB2 boosterpack to PB2 pin and TamperIO
J15 PA7/TIO Connection Center and bottom connection PA7 boosterpack to PA7 pin and TamperIO
J16 Red LED connection (LED5) Unpopulated Through 470Ω resistor and LED to ground
J17 UART RX Top and center connection PA11 to XDS
PA11 to PA11 boosterpack
J18 UART TX Top and center connection PA10 to XDS
PA10 to PA10 boosterpack
J19 BSL Button Populated PA18: 47kΩ pull down resistor, switch pulls up to 3.3V
J20 Switch connection (S2) Populated

PB8: switch pulls down to GND