SFFSBP6 November   2026 TPS281C100

 

  1.   1
  2.   Trademarks
  3. 1Overview
  4. 2Functional Safety Failure In Time (FIT) Rates
  5. 3Failure Mode Distribution (FMD)
  6. 4Pin Failure Mode Analysis (Pin FMA)
  7. 5Revision History

Pin Failure Mode Analysis (Pin FMA)

This section provides a failure mode analysis (FMA) for the pins of the TPS281C100x. The failure modes covered in this document include the typical pin-by-pin failure scenarios:

  • Pin short-circuited to ground (see Table 4-2)
  • Pin open-circuited (see Table 4-3)
  • Pin short-circuited to an adjacent pin (see Table 4-4)
  • Pin short-circuited to supply (see Table 4-5)

Table 4-2 through Table 4-5 also indicate how these pin conditions can affect the device as per the failure effects classification in Table 4-1.

Table 4-1 TI Classification of Failure Effects
ClassFailure Effects
APotential device damage that affects functionality.
BNo device damage, but loss of functionality.
CNo device damage, but performance degradation.
DNo device damage, no impact to functionality or performance.

Figure 4-1 shows the TPS281C100x pin diagram. For a detailed description of the device pins, see the Pin Configuration and Functions section in the TPS281C100x datasheet.

TPS281C100 Pin DiagramFigure 4-1 Pin Diagram

Following are the assumptions of use and the device configuration assumed for the pin FMA in this section:

  • The user follows the datasheet recommendations for operating conditions, external components selection, and PCB layout.
Table 4-2 Pin FMA for Device Pins Short-Circuited to Ground
Pin NamePin No.Description of Potential Failure EffectsFailure Effect Class
OL_ON1High accuracy sense mode is disabled.C
SNS2The sense current is not valid from the SNS pin.B
ILIM3The device defaults to the internal current limit.C
NC4, 9There is no effect on the device.D
VOUT5, 6The current limit of the device engages.B
VS7, 8The device has no input supply, and therefore, does not function.B
FAULT10The reported status can be erroneous.B
DIAG_EN11The diagnostics disable.B
EN12The output shuts down.B
Table 4-3 Pin FMA for Device Pins Open-Circuited
Pin NamePin No.Description of Potential Failure EffectsFailure Effect Class
OL_ON 1 High accuracy sense mode disables. The OL_ON pin pulls down internally. B
SNS2The correct sense current cannot be read.B
ILIM3The device defaults to the internal current limit.C
NC4, 9There is no effect on the device.D
VOUT5, 6There is no effect on the device. The open load detection triggers.B
VS7, 8The device has no input supply, and therefore, does not function.B
FAULT10The fault signal is not reported.B
DIAG_EN11The pin is internally pulled down. The diagnostics disable.B
EN12The output shuts down and the EN pin pulls down internally.B
Table 4-4 Pin FMA for Device Pins Short-Circuited to Adjacent Pin
Pin NamePin No.Shorted toDescription of Potential Failure EffectsFailure Effect Class
OL_ON 1 SNS The current sensing output is erroneous. The device is in standard sensing or high accuracy sensing depending on the output of the SNS pin. B
SNS2ILIMThe current limit and current sensing outputs are incorrect.B
ILIM3NCThere is no effect on the device.D
NC4VOUTThere is no effect on the device.D
VS8NCThere is no effect on the device.D
NC9FAULTThere is no effect on the device.D
FAULT10DIAG_ENFault reporting is erroneous. Diagnostics enable if FAULT pulls high.B
DIAG_EN11ENThe EN signal effects the DIAG_EN signal and vice versa.B
Table 4-5 Pin FMA for Device Pins Short-Circuited to Supply
Pin NamePin No.Description of Potential Failure EffectsFailure Effect Class
OL_ON 1 There is a potential violation of the absolute maximum rating of the pin and a possible breakdown of the ESD cell. A
SNS2There is a potential violation of the absolute maximum rating of the pin and a possible breakdown of the ESD cell.A
ILIM3There is a potential violation of the absolute maximum rating of the pin and a possible breakdown of the ESD cell.A
NC4, 9There is no effect on the device.D
VOUT5, 6The output pulls to supply voltage.B
FAULT10There is a potential violation of the absolute maximum rating of the pin and a possible breakdown of the ESD cell.A
DIAG_EN11There is a potential violation of the absolute maximum rating of the pin and a possible breakdown of the ESD cell.A
EN12There is a potential violation of the absolute maximum rating of the pin and a possible breakdown of the ESD cell.A