SLASF29A January   2022  – October 2024 TAA5242

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements: TDM, I2S or LJ Interface
    7. 5.7 Switching Characteristics: TDM, I2S or LJ Interface
    8. 5.8 Timing Diagrams
    9. 5.9 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Hardware Control
      2. 6.3.2 Audio Serial Interfaces
        1. 6.3.2.1 Time Division Multiplexed Audio (TDM) Interface
        2. 6.3.2.2 Inter IC Sound (I2S) Interface
        3. 6.3.2.3 Left-Justified (LJ) Interface
      3. 6.3.3 Phase-Locked Loop (PLL) and Clock Generation
      4. 6.3.4 Analog Input Configurations
      5. 6.3.5 Reference Voltage
      6. 6.3.6 Integrated Microphone Bias
      7. 6.3.7 Signal-Chain Processing
        1. 6.3.7.1 Configurable Digital Decimation Filters
          1. 6.3.7.1.1 Linear-phase filters
            1. 6.3.7.1.1.1 Sampling Rate: 8kHz or 7.35kHz
            2. 6.3.7.1.1.2 Sampling Rate: 16kHz or 14.7kHz
            3. 6.3.7.1.1.3 Sampling Rate: 24kHz or 22.05kHz
            4. 6.3.7.1.1.4 Sampling Rate: 32kHz or 29.4kHz
            5. 6.3.7.1.1.5 Sampling Rate: 48kHz or 44.1kHz
            6. 6.3.7.1.1.6 Sampling Rate: 96kHz or 88.2kHz
            7. 6.3.7.1.1.7 Sampling Rate: 192kHz or 176.4kHz
          2. 6.3.7.1.2 Low-latency Filters
            1. 6.3.7.1.2.1 Sampling Rate: 24kHz or 22.05kHz
            2. 6.3.7.1.2.2 Sampling Rate: 32kHz or 29.4kHz
            3. 6.3.7.1.2.3 Sampling Rate: 48kHz or 44.1kHz
            4. 6.3.7.1.2.4 Sampling Rate: 96kHz or 88.2kHz
            5. 6.3.7.1.2.5 Sampling Rate: 192kHz or 176.4kHz
        2. 6.3.7.2 Programmable Digital High-Pass Filter
    4. 6.4 Device Functional Modes
      1. 6.4.1 Active Mode
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Application
      2. 7.2.2 Design Requirements
      3. 7.2.3 Detailed Design Procedure
      4. 7.2.4 Application Performance Plots
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Documentation Support
      1. 8.1.1 Related Documentation
    2. 8.2 Receiving Notification of Documentation Updates
    3. 8.3 Support Resources
    4. 8.4 Trademarks
    5. 8.5 Electrostatic Discharge Caution
    6. 8.6 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

4 Pin Configuration and Functions

TAA5242 24-Pin QFN Package with Exposed Thermal Pad and Corner Pins, Top View Figure 4-1 24-Pin QFN Package with Exposed Thermal Pad and Corner Pins, Top View
Table 4-1 Pin Functions
PIN TYPE DESCRIPTION
NAME NO.
VSS A1 Ground Ground Pin. Short directly to board ground plane.
DREG 1 Digital Supply Digital on-chip regulator output voltage for digital supply (1.55V, nominal)
BCLK 2 Digital I/O Audio serial data interface bus bit clock
FSYNC 3 Digital I/O Audio serial data interface bus frame synchronization signal
DOUT 4 Digital Output Audio serial data interface bus output
MD6 5 Digital Input TDM Mode: Daisy chain input
I2S/LJ Mode: Mono/Stereo ADC channels selection
IOVDD 6 Digital Supply Digital I/O power supply (1.8V or 3.3V, nominal)
VSS A2 Ground Ground pin. Short directly to board ground plane.
MD1 7 Digital Input Controller Mode: Frame rate and BCLK frequency selection
Target Mode: AVDD supply, word length, and decimation filter type selection
MD2 8 Digital Input Controller Mode: Frame rate and BCLK frequency selection
Target Mode: AVDD supply, word length, and decimation filter type selection
MD3 9 Digital Input Controller Mode: Controller clock input
TDM Target Mode: Daisy chain enable/disable
I2S/LJ Target Mode: Digital HPF cut-off frequency and input cap quick charge setting
MD4 10 Digital Input ADC input configuration selection
GPO 11 Digital Output Interrupt Output (latched)
MD5 12 Digital Input ADC input configuration selection
VSS A3 Ground Ground pin. Short directly to board ground plane.
MD0 13 Analog Input Multi-Level analog input for Controller/Target and I2S/TDM/LJ selection
MICBIAS 14 Analog MICBIAS Output
IN1P 15 Analog Input Analog input 1P Pin
IN1M 16 Analog Input Analog input 1M Pin
IN2P 17 Analog Input Analog input 2P Pin
IN2M 18 Analog Input Analog input 2M Pin
VSS A4 Ground Ground pin. Short directly to board ground plane.
VSSA 19 Ground Short directly to board ground plane
VSSA 20 Ground Short directly to board ground plane
VSSA 21 Ground Short directly to board ground plane
VSSA 22 Ground Short directly to board ground plane
AVDD 23 Analog Supply Analog power supply (1.8V or 3.3V, nominal)
VREF 24 Analog Analog reference voltage filter output