SLASFN4 December   2025 DAC60516W

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics
    6. 5.6  Timing Requirements - I2C Standard Mode
    7. 5.7  Timing Requirements - I2C Fast Mode
    8. 5.8  Timing Requirements - I2C Fast Mode Plus
    9. 5.9  Timing Requirements - SPI
    10. 5.10 Switching Characteristics
    11. 5.11 Timing Diagrams
    12. 5.12 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Digital-to-Analog Converter (DAC) Architecture
        1. 6.3.1.1 DAC Register Structure
          1. 6.3.1.1.1 DAC Synchronous Operation
          2. 6.3.1.1.2 DAC Buffer Amplifier
          3. 6.3.1.1.3 DAC Transfer Function
      2. 6.3.2 Internal Reference
      3. 6.3.3 Power-On Reset (POR)
    4. 6.4 Device Functional Modes
      1. 6.4.1 Clear Mode
    5. 6.5 Programming
      1. 6.5.1 I2C Serial Interface
        1. 6.5.1.1 I2C Bus Overview
        2. 6.5.1.2 I2C Bus Definitions
        3. 6.5.1.3 I2C Target Address Selection
        4. 6.5.1.4 I2C Read and Write Operations
        5. 6.5.1.5 I2C General-Call Reset
      2. 6.5.2 Serial Peripheral Interface (SPI)
        1. 6.5.2.1 SPI Bus Overview
  8. 7 Register Map
    1. 7.1 Registers
  9. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Bipolar Voltage Output
    2. 8.2 Typical Application
      1. 8.2.1 Programmable High-Current Voltage Output Circuit
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Curve
    3. 8.3 Initialization Setup
    4. 8.4 Power Supply Recommendations
    5. 8.5 Layout
      1. 8.5.1 Layout Guidelines
      2. 8.5.2 Layout Examples
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Registers

7.1.1 NOP Register (Offset = 0h) [Reset = 0000h]

Figure 7-1 NOP Register
15141312111098
NOP[15:0]
W-0h
76543210
NOP[15:0]
W-0h
Table 7-2 NOP Register Field Descriptions
BitFieldTypeResetDescription
15:0NOP[15:0]W0h
No Operation (NOP).

7.1.2 DEVICE_ID Register (Offset = 1h) [Reset = 6A16h]

Figure 7-2 DEVICE_ID Register
15141312111098
CHIP_ID[15:0]
R-6Ah
76543210
CHIP_ID[15:0]
R-16h
Table 7-3 DEVICE_ID Register Field Descriptions
BitFieldTypeResetDescription
15:0 CHIP_ID[15:0] R 6A16h Device Chip ID. For the DAC60516W device, this register reads back the value 6A16h

7.1.3 VERSION_ID Register (Offset = 2h) [Reset = 0000h]

Figure 7-3 VERSION_ID Register
15141312111098
RESERVED
R-0h
76543210
RESERVEDVERSION_ID[2:0]
R-0hR-0h
Table 7-4 VERSION_ID Register Field Descriptions
BitFieldTypeResetDescription
15:3RESERVEDR0h
2:0VERSION_ID[2:0]R0hDevice Version ID.

7.1.4 PWDWN Register (Offset = 3h) [Reset = FFFFh]

Figure 7-4 PWDWN Register
15141312111098
OUT15_PWDWNOUT14_PWDWNOUT13_PWDWNOUT12_PWDWNOUT11_PWDWNOUT10_PWDWNOUT9_PWDWNOUT8_PWDWN
R/W-1hR/W-1hR/W-1hR/W-1hR/W-1hR/W-1hR/W-1hR/W-1h
76543210
OUT7_PWDWNOUT6_PWDWNOUT5_PWDWNOUT4_PWDWNOUT3_PWDWNOUT2_PWDWNOUT1_PWDWNOUT0_PWDWN
R/W-1hR/W-1hR/W-1hR/W-1hR/W-1hR/W-1hR/W-1hR/W-1h
Table 7-5 PWDWN Register Field Descriptions
BitFieldTypeResetDescription
15OUT15_PWDWNR/W1h
OUT15 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
14OUT14_PWDWNR/W1h
OUT14 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
13OUT13_PWDWNR/W1h
OUT13 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
12OUT12_PWDWNR/W1h
OUT12 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
11OUT11_PWDWNR/W1h
OUT11 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
10OUT10_PWDWNR/W1h
OUT10 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
9OUT9_PWDWNR/W1h
OUT9 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
8OUT8_PWDWNR/W1h
OUT8 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
7OUT7_PWDWNR/W1h
OUT7 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
6OUT6_PWDWNR/W1h
OUT6 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
5OUT5_PWDWNR/W1h
OUT5 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
4OUT4_PWDWNR/W1h
OUT4 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
3OUT3_PWDWNR/W1h
OUT3 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
2OUT2_PWDWNR/W1h
OUT2 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
1OUT1_PWDWNR/W1h
OUT1 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode
0OUT0_PWDWNR/W1h
OUT0 power down bit.
0h = This DAC is enabled
1h = This DAC is disabled in a low-power mode

7.1.5 DAC_GAIN Register (Offset = 4h) [Reset = 0000h]

Figure 7-5 DAC_GAIN Register
15141312111098
RESERVED
R-0h
76543210
RESERVEDOUT_QUAD3_GAINOUT_QUAD2_GAINOUT_QUAD1_GAINOUT_QUAD0_GAIN
R-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 7-6 DAC_GAIN Register Field Descriptions
BitFieldTypeResetDescription
15:4RESERVEDR0h
3OUT_QUAD3_GAINR/W0hQUAD-3 VREF Gain.
VREF gain setting for OUT12, OUT13, OUT14, OUT15.
0h = This group of DACs is in 0V to 1 × VREF output range
1h = This group of DACs is in 0V to 2 × VREF output range
2OUT_QUAD2_GAINR/W0hQUAD-2 VREF Gain.
VREF gain setting for OUT8, OUT9, OUT10, OUT11.
0h = This group of DACs is in 0V to 1 × VREF output range
1h = This group of DACs is in 0V to 2 × VREF output range
1OUT_QUAD1_GAINR/W0hQUAD-1 VREF Gain.
VREF gain setting for OUT4, OUT5, OUT6, OUT7.
0h = This group of DACs is in 0V to 1 × VREF output range
1h = This group of DACs is in 0V to 2 × VREF output range
0OUT_QUAD0_GAINR/W0hQUAD-0 VREF Gain.
VREF gain setting for OUT0, OUT1, OUT2, OUT3.
0h = This group of DACs is in 0V to 1 × VREF output range
1h = This group of DACs is in 0V to 2 × VREF output range

7.1.6 TRIGGER Register (Offset = 5h) [Reset = 0000h]

Figure 7-6 TRIGGER Register
15141312111098
LDAC_
OUT15_OUT14
LDAC_
OUT13_OUT12
LDAC_
OUT11_OUT10
LDAC_
OUT9_OUT8
LDAC_
OUT7_OUT6
LDAC_
OUT5_OUT4
LDAC_
OUT3_OUT2
LDAC_
OUT1_OUT0
W-0hW-0hW-0hW-0hW-0hW-0hW-0hW-0h
76543210
RESERVEDSOFT_RST[3:0]
R-0hW-0h
Table 7-7 TRIGGER Register Field Descriptions
BitFieldTypeResetDescription
15LDAC_OUT15_OUT14W0hSoftware DAC trigger.
Transfers DAC data from OUT15 and OUT14 buffer registers to active registers if corresponding channels are configured in synchronous mode. This bit self-clears when action is completed.
0h = No action
1h = Transfer DAC data. This bit clears when action is completed.
14LDAC_OUT13_OUT12W0hSoftware DAC trigger.
Transfers DAC data from OUT13 and OUT12 buffer registers to active registers if corresponding channels are configured in synchronous mode. This bit self-clears when action is completed.
0h = No action
1h = Transfer DAC data. This bit clears when action is completed.
13LDAC_OUT11_OUT10W0hSoftware DAC trigger.
Transfers DAC data from OUT11 and OUT10 buffer registers to active registers if corresponding channels are configured in synchronous mode. This bit self-clears when action is completed.
0h = No action
1h = Transfer DAC data. This bit clears when action is completed.
12LDAC_OUT9_OUT8W0hSoftware DAC trigger.
Transfers DAC data from OUT9 and OUT8 buffer registers to active registers if corresponding channels are configured in synchronous mode. This bit self-clears when action is completed.
0h = No action
1h = Transfer DAC data. This bit clears when action is completed.
11LDAC_OUT7_OUT6W0hSoftware DAC trigger.
Transfers DAC data from OUT7 and OUT6 buffer registers to active registers if corresponding channels are configured in synchronous mode. This bit self-clears when action is completed.
0h = No action
1h = Transfer DAC data. This bit clears when action is completed.
10LDAC_OUT5_OUT4W0hSoftware DAC trigger.
Transfers DAC data from OUT5 and OUT4 buffer registers to active registers if corresponding channels are configured in synchronous mode. This bit self-clears when action is completed.
0h = No action
1h = Transfer DAC data. This bit clears when action is completed.
9LDAC_OUT3_OUT2W0hSoftware DAC trigger.
Transfers DAC data from OUT3 and OUT2 buffer registers to active registers if corresponding channels are configured in synchronous mode. This bit self-clears when action is completed.
0h = No action
1h = Transfer DAC data. This bit clears when action is completed.
8LDAC_OUT1_OUT0W0hSoftware DAC trigger.
Transfers DAC data from OUT1 and OUT0 buffer registers to active registers if corresponding channels are configured in synchronous mode. This bit self-clears when action is completed.
0h = No action
1h = Transfer DAC data. This bit clears when action is completed.
7:4RESERVEDR0h
3:0SOFT_RST[3:0]W0hSoftware device reset.

Ah = Software Reset. Executes a full power-on-reset. Resets the device and all registers to the default power-on-reset state. Auto clears with execution.

7.1.7 BCAST_DAC_DATA Register (Offset = 6h) [Reset = 0000h]

Figure 7-7 BCAST_DAC_DATA Register
15 14 13 12 11 10 9 8
DATA[11:4]
R/W-0h
7 6 5 4 3 2 1 0
DATA[3:0] RESERVED
R/W-0h R-0h
Table 7-8 BCAST_DAC_DATA Register Field Descriptions
Bit Field Type Reset Description
15:4 DATA[11:0] R/W 0h A write to this register sets all DAC buffer and active register values to the specified code, on output channels for which the broadcast enable bit is set.
3:0 RESERVED R 0h

7.1.8 STATUS Register (Offset = 7h) [Reset = 4008h]

Figure 7-8 STATUS Register
15141312111098
RESERVED
R-40h
76543210
RESERVEDGDAC_SC_STS
R-04hR-0h
Table 7-9 STATUS Register Field Descriptions
BitFieldTypeResetDescription
15:1RESERVEDR2004h
0GDAC_SC_STSR0hGlobal DAC short circuit status.
Global DAC short circuit status bit. This bit is the OR function of all DACn_SC_STS bits. DACn_SC_STS bits are located in DAC_STATUS register having one bit per DAC.
0h = No DAC output channels are in a short-circuit condition
1h = At least one DAC output channel is in a short-circuit condition

7.1.9 SDO_EN Register (Offset = 8h) [Reset = 0000h]

Figure 7-9 SDO_EN Register
15141312111098
RESERVED
R-0h
76543210
RESERVEDFSDOSDO_EN
R-0hR/W-0hR/W-0h
Table 7-10 SDO_EN Register Field Descriptions
BitFieldTypeResetDescription
15:2RESERVEDR0h
1FSDOR/W0hFast SDO.
Allows faster SPI bus speeds by sending the SDO data out one SCLK half-cycle earlier. SDI latching edge is always SCLK falling edge regardless of this setting. FSDO is ignored when SDO_EN is disabled.
0h = SDO drives MSB when chip select goes low and then updates on each SCLK rising edge (opposite edge of SDI latching edge).
1h = SDO drives MSB when chip select goes low and then updates on each SCLK falling edge (same edge as SDI latching edge)
0SDO_ENR/W0hSDO enable.
Enable the SDO pin driver. When enabled, SDO is enabled for read and writes whenever SPI chip-select pin is low. SDO is always disabled in I2C mode regardless of this bit setting.
0h = SDO disabled
1h = SDO enabled during read and write operations

7.1.10 GEN_CONFIG Register (Offset = 9h) [Reset = 0014h]

Figure 7-10 GEN_CONFIG Register
15141312111098
RESERVED
R-0h
76543210
RESERVEDFLEXIO_OUT_POLFLEXIO_OUT_ODERESERVEDREF_PWDWNRESERVEDFLEXIO_FUNC
R-0hR/W-0hR/W-1hR-0hR/W-1hR-0hR/W-0h
Table 7-11 GEN_CONFIG Register Field Descriptions
BitFieldTypeResetDescription
15:6RESERVEDR0h
5FLEXIO_OUT_POLR/W0hFLEXIO pin polarity.
Set the FLEXIO pin output active state (when pin is configured as GPIO).
0h = FLEXIO digital pin outputs 0V if GPIO_DATA is set to 0x00h (or high-impedance, when configured as open-drain), and VIO if GPIO_DATA is set to 0x01h
1h = FLEXIO digital pin outputs VIO (or high-impedance, when configured as open-drain) if GPIO_DATA is set to 0x00h, and 0V if GPIO_DATA is set to 0x01h
4FLEXIO_OUT_ODER/W1hFLEXIO open drain enable.
Set the FLEXIO pin drive mode (when pin is configured as GPIO). Do not raise pin above the absolute maximum ratings with respect to VIO voltage. Bit is ignored if pin is not configured as a digital output.
0h = FLEXIO pin output is push-pull
1h = FLEXIO pin output is open-drain
3RESERVEDR0h
2REF_PWDWNR/W1hDisable internal reference.
Set to enable or disable the internal voltage reference.
0h = Internal reference enabled
1h = Internal reference disabled
1RESERVEDR0h
0FLEXIO_FUNCR/W0hFLEXIO pin function.
Sets the function of FLEXIO pin.
0h = GPIO. In this mode, the pin operates as a GPIO and the GPIO_DATA register is used to support GPIO functionality.
1h = CLEAR pin. In this mode, the pin operates as an active-low DAC Clear input pin.

7.1.11 SYNC_EN Register (Offset = Ah) [Reset = 0000h]

Figure 7-11 SYNC_EN Register
15141312111098
OUT15_
SYNC_EN
OUT14_
SYNC_EN
OUT13_
SYNC_EN
OUT12_
SYNC_EN
OUT11_
SYNC_EN
OUT10_
SYNC_EN
OUT9_
SYNC_EN
OUT8_
SYNC_EN
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
76543210
OUT7_
SYNC_EN
OUT6_
SYNC_EN
OUT5_
SYNC_EN
OUT4_
SYNC_EN
OUT3_
SYNC_EN
OUT2_
SYNC_EN
OUT1_
SYNC_EN
OUT0_
SYNC_EN
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 7-12 SYNC_EN Register Field Descriptions
BitFieldTypeResetDescription
15OUT15_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
14OUT14_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
13OUT13_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
12OUT12_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
11OUT11_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
10OUT10_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
9OUT9_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
8OUT8_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
7OUT7_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
6OUT6_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
5OUT5_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
4OUT4_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
3OUT3_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
2OUT2_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
1OUT1_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)
0OUT0_SYNC_ENR/W0hSynchronous mode enable.
Enable or disable synchronous mode.
0h = Set this DAC into asynchronous mode (DAC active register updates when DAC buffer is updated)
1h = Set this DAC into synchronous mode (DAC active register updates with DAC trigger)

7.1.12 BCAST_EN Register (Offset = Bh) [Reset = FFFFh]

Figure 7-12 BCAST_EN Register
15141312111098
OUT15_
BCAST_EN
OUT14_
BCAST_EN
OUT13_
BCAST_EN
OUT12_
BCAST_EN
OUT11_
BCAST_EN
OUT10_
BCAST_EN
OUT9_
BCAST_EN
OUT8_
BCAST_EN
R/W-1hR/W-1hR/W-1hR/W-1hR/W-1hR/W-1hR/W-1hR/W-1h
76543210
OUT7_
BCAST_EN
OUT6_
BCAST_EN
OUT5_
BCAST_EN
OUT4_
BCAST_EN
OUT3_
BCAST_EN
OUT2_
BCAST_EN
OUT1_
BCAST_EN
OUT0_
BCAST_EN
R/W-1hR/W-1hR/W-1hR/W-1hR/W-1hR/W-1hR/W-1hR/W-1h
Table 7-13 BCAST_EN Register Field Descriptions
BitFieldTypeResetDescription
15OUT15_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
14OUT14_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
13OUT13_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
12OUT12_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
11OUT11_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
10OUT10_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
9OUT9_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
8OUT8_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
7OUT7_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
6OUT6_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
5OUT5_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
4OUT4_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
3OUT3_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
2OUT2_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
1OUT1_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC
0OUT0_BCAST_ENR/W1h
Enable or disable broadcast mode.
0h = Ignore broadcast writes on this DAC
1h = Allow broadcast writes on this DAC

7.1.13 CLEAR Register (Offset = Ch) [Reset = 0000h]

Figure 7-13 CLEAR Register
15141312111098
OUT15_
SW_CLR
OUT14_
SW_CLR
OUT13_
SW_CLR
OUT12_
SW_CLR
OUT11_
SW_CLR
OUT10_
SW_CLR
OUT9_
SW_CLR
OUT8_
SW_CLR
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
76543210
OUT7_
SW_CLR
OUT6_
SW_CLR
OUT5_
SW_CLR
OUT4_
SW_CLR
OUT3_
SW_CLR
OUT2_
SW_CLR
OUT1_
SW_CLR
OUT0_
SW_CLR
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 7-14 CLEAR Register Field Descriptions
BitFieldTypeResetDescription
15OUT15_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
14OUT14_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
13OUT13_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
12OUT12_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
11OUT11_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
10OUT10_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
9OUT9_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
8OUT8_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
7OUT7_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
6OUT6_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
5OUT5_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
4OUT4_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
3OUT3_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
2OUT2_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
1OUT1_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state
0OUT0_SW_CLRR/W0hSoftware clear enable bit.
Forces DAC to enter clear state. DAC uses clear code that is specified in clear state.
0h = Restore this DAC to normal operation
1h = Force this DAC into clear state

7.1.14 CLEAR_PIN_MASK Register (Offset = Dh) [Reset = 0000h]

Figure 7-14 CLEAR_PIN_MASK Register
15141312111098
OUT15_
HW_CLR_MASK
OUT14_
HW_CLR_MASK
OUT13_
HW_CLR_MASK
OUT12_
HW_CLR_MASK
OUT11_
HW_CLR_MASK
OUT10_
HW_CLR_MASK
OUT9_
HW_CLR_MASK
OUT8_
HW_CLR_MASK
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
76543210
OUT7_
HW_CLR_MASK
OUT6_
HW_CLR_MASK
OUT5_
HW_CLR_MASK
OUT4_
HW_CLR_MASK
OUT3_
HW_CLR_MASK
OUT2_
HW_CLR_MASK
OUT1_
HW_CLR_MASK
OUT0_
HW_CLR_MASK
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 7-15 CLEAR_PIN_MASK Register Field Descriptions
BitFieldTypeResetDescription
15OUT15_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
14OUT14_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
13OUT13_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
12OUT12_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
11OUT11_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
10OUT10_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
9OUT9_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
8OUT8_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
7OUT7_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
6OUT6_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
5OUT5_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
4OUT4_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
3OUT3_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
2OUT2_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
1OUT1_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel
0OUT0_HW_CLR_MASKR/W0hMask bit for CLEAR (FLEXIO) pin.
0h = CLEAR pin affects this DAC channel
1h = CLEAR pin does not affect this DAC channel

7.1.15 BCAST_CLR_DATA Register (Offset = Eh) [Reset = 0000h]

Figure 7-15 BCAST_CLR_DATA Register
15 14 13 12 11 10 9 8
DATA[11:4]
R/W-0h
7 6 5 4 3 2 1 0
DATA[3:0] RESERVED
R/W-0h R-0h
Table 7-16 BCAST_CLR_DATA Register Field Descriptions
Bit Field Type Reset Description
15:4 DATA[11:0] R/W 0h A write to this register sets all DAC clear code register values to the specified code on output channels for which the broadcast enable bit is set.
3:0 RESERVED R 0h

7.1.16 RESET_FLAGS Register (Offset = Fh) [Reset = 000Fh]

Figure 7-16 RESET_FLAGS Register
15141312111098
RESERVED
R-0h
76543210
RESERVEDAVDD_
COLLAPSE_
FLAG
RSTPIN_
FLAG
VIO_
FLAG
PORBASE_
FLAG
R-0hW-1hW-1hW-1hW-1h
Table 7-17 RESET_FLAGS Register Field Descriptions
BitFieldTypeResetDescription
4AVDD_COLLAPSE_FLAGW1hWrite to 0 to detect a AVDD collapse event, at which time this flag is automatically set to 1. AVDD collapse occurs when AVDD pin voltage reaches to within 1V of the VREF voltage.
3RSTPIN_FLAGW1hWrite to 0 to detect a RESET pin reset event, at which time this flag is automatically set to 1.
2VIO_FLAGW1hWrite to 0 to detect a VIO reset event, at which time this flag is automatically set to 1. VIO reset event occurs as a result of VIO pin voltage dropping to less than the POR threshold voltage.
1PORBASE_FLAGW1hWrite to 0 to detect a POR-base reset event, at which time this flag is automatically set to 1. A POR-base reset event occurs as a result of VDD dropping to less than the POR threshold voltage.

7.1.17 OUTn_BUFFER_CODE Registers (Offset = 10h to 1Fh) [Reset = 0000h]

Figure 7-17 OUTn_BUFFER_CODE Register
15 14 13 12 11 10 9 8
DATA[11:4]
R/W-0h
7 6 5 4 3 2 1 0
DATA[3:0] RESERVED
R/W-0h R-0h
Table 7-18 OUTn_BUFFER_CODE Register Field Descriptions
Bit Field Type Reset Description
15:4 DATA[11:0] R/W 0h Code for OUTn buffer register, unipolar straight binary format.
3:0 RESERVED R 0h
Note: n = 0 to 16, corresponding to each respective OUT channel on the device.

7.1.18 OUTn_CLEAR_CODE Registers (Offset = 20h to 2Fh) [Reset = 0000h]

Figure 7-18 OUTn_CLEAR_CODE Register
15 14 13 12 11 10 9 8
DATA[11:4]
R/W-0h
7 6 5 4 3 2 1 0
DATA[3:0] RESERVED
R/W-0h R-0h
Table 7-19 OUTn_CLEAR_CODE Register Field Descriptions
Bit Field Type Reset Description
15:4 DATA[11:0] R/W 0h Code for OUTn clear register, unipolar straight binary format.
3:0 RESERVED R 0h
Note: n = 0 to 16, corresponding to each respective OUT channel on the device.

7.1.19 GPIO_DATA Register (Offset = 31h) [Reset = 0001h]

Figure 7-19 GPIO_DATA Register
15 14 13 12 11 10 9 8
RESERVED
R-0h
7 6 5 4 3 2 1 0
RESERVED GPIO
R-0h R/W-1h
Table 7-20 GPIO_DATA Register Field Descriptions
Bit Field Type Reset Description
15:1 RESERVED R 0h
0 GPIO R/W 1h GPIO bit.
For write operation, the GPIO pin operates as an output. Write a 1 to set the corresponding GPIO pin to either high impedance (FLEXIO_OUT_ODE=1) or logic 1 (FLEXIO_OUT_ODE=0). Write a 0 to set the corresponding GPIO pin to logic low. For read operations the GPIO pin operates as an input. Read to receive the status of the corresponding GPIO pin, which is determined by the voltage at the pin; the bit reads as 0 at start-up if the voltage at this pin is less than VIH (the register value, 1 by default, is not returned when a read command is issued in this circumstance). After a reset event, the GPIO pin is in a high-impedance state.

7.1.20 DAC_STATUS Register (Offset = 32h) [Reset = 0000h]

Figure 7-20 DAC_STATUS Register
15141312111098
OUT15_
SC_STS
OUT14_
SC_STS
OUT13_
SC_STS
OUT12_
SC_STS
OUT11_
SC_STS
OUT10_
SC_STS
OUT9_
SC_STS
OUT8_
SC_STS
R-0hR-0hR-0hR-0hR-0hR-0hR-0hR-0h
76543210
OUT7_
SC_STS
OUT6_
SC_STS
OUT5_
SC_STS
OUT4_
SC_STS
OUT3_
SC_STS
OUT2_
SC_STS
OUT1_
SC_STS
OUT0_
SC_STS
R-0hR-0hR-0hR-0hR-0hR-0hR-0hR-0h
Table 7-21 DAC_STATUS Register Field Descriptions
BitFieldTypeResetDescription
15OUT15_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
14OUT14_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
13OUT13_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
12OUT12_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
11OUT11_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
10OUT10_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
9OUT9_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
8OUT8_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
7OUT7_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
6OUT6_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
5OUT5_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
4OUT4_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
3OUT3_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
2OUT2_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
1OUT1_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition
0OUT0_SC_STSR0hDAC short circuit condition, indicating whether this DAC channel is shorted to ground.
0h = DAC channel is not in short circuit condition
1h = DAC channel is in short circuit condition