SLUSDW2C November   2021  – May 2025 BQ27Z746

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configurations and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
      1. 5.5.1 Supply Current
      2. 5.5.2 Common Analog (LDO, LFO, HFO, REF1, REF2, I-WAKE)
      3. 5.5.3 Battery Protection (CHG, DSG)
      4. 5.5.4 Cell Sensing Output (BAT_SP, BAT_SN)
      5. 5.5.5 Gauge Measurements (ADC, CC, Temperature)
      6. 5.5.6 Flash Memory
    6. 5.6 Digital I/O: DC Characteristics
    7. 5.7 Digital I/O: Timing Characteristics
    8. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  BQ27Z746 Processor
      2. 6.3.2  Battery Parameter Measurements
        1. 6.3.2.1 Coulomb Counter (CC) and Digital Filter
        2. 6.3.2.2 ADC Multiplexer
        3. 6.3.2.3 Analog-to-Digital Converter (ADC)
        4. 6.3.2.4 Internal Temperature Sensor
        5. 6.3.2.5 External Temperature Sensor Support
      3. 6.3.3  Power Supply Control
      4. 6.3.4  ENAB Pin
      5. 6.3.5  Bus Communication Interface
      6. 6.3.6  Low Frequency Oscillator
      7. 6.3.7  High Frequency Oscillator
      8. 6.3.8  1.8-V Low Dropout Regulator
      9. 6.3.9  Internal Voltage References
      10. 6.3.10 Overcurrent in Discharge Protection
      11. 6.3.11 Overcurrent in Charge Protection
      12. 6.3.12 Short-Circuit Current in Discharge Protection
      13. 6.3.13 Primary Protection Features
      14. 6.3.14 Battery Sensing
      15. 6.3.15 Gas Gauging
      16. 6.3.16 Zero Volt Charging (ZVCHG)
      17. 6.3.17 Charge Control Features
      18. 6.3.18 Authentication
    4. 6.4 Device Functional Modes
      1. 6.4.1 Lifetime Logging Features
      2. 6.4.2 Configuration
        1. 6.4.2.1 Coulomb Counting
        2. 6.4.2.2 Cell Voltage Measurements
        3. 6.4.2.3 Auto Calibration
        4. 6.4.2.4 Temperature Measurements
  8. 7 Applications and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Applications
      1. 7.2.1 Design Requirements (Default)
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 Changing Design Parameters
      3. 7.2.3 Calibration Process
      4. 7.2.4 Gauging Data Updates
        1. 7.2.4.1 Application Curve
  9. 8 Power Supply Requirements
  10. 9 Layout
    1. 9.1 Layout Guidelines
    2. 9.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Third-Party Products Disclaimer
    2. 10.2 Documentation Support
      1. 10.2.1 Related Documentation
    3. 10.3 Receiving Notification of Documentation Updates
    4. 10.4 Support Resources
    5. 10.5 Trademarks
    6. 10.6 Electrostatic Discharge Caution
    7. 10.7 Glossary
  12. 11Revision History
  13. 12Mechanical, Orderable, and Packaging Information

5.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN NOM MAX UNIT
Supply voltage range VDD 2.0 5.5 V
Input voltage range PACK (with 5 kΩ RPACK current limit) 0 12 V
PACK (no RPACK current limit) 0 5.5
BAT 1.5 5.5
SDA, SCL, ENAB –0.3 VDD
TS VSS 1.8
SRN, SRP VCC_CM – 0.1 VCC_CM + 0.1
Output voltage range BAT_SP, BAT_SN 2 VDD +VOFFS V
GPO VSS 1.8
CHG, DSG VSS VDD+ (VDD × AFETON)
External Decoupling Capacitor on VDD pin, CVDD 1 µF
External Decoupling Capacitor on TS pin, CTS

0.01

 µF
External Sense Resistor from PACK+ terminal to device PACK pin, RPACK 5 kΩ
External Sense Resistor from PACK+ terminal to device DSG pin, RDSG 10 MΩ
External Sense Resistor from SRN to SRP pins, RSNS
 1 20 mΩ
Operating Temperature, TA -40 85 ℃