SLUSF78A June   2023  – November 2024 UCC28731-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
    1.     Pin Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Detailed Pin Description
        1. 6.3.1.1 VDD (Device Bias Voltage Supply)
        2. 6.3.1.2 GND (Ground)
        3. 6.3.1.3 HV (High Voltage Startup)
        4. 6.3.1.4 DRV (Gate Drive)
        5. 6.3.1.5 CBC (Cable Compensation)
        6. 6.3.1.6 VS (Voltage Sense)
        7. 6.3.1.7 CS (Current Sense)
      2. 6.3.2 Primary-Side Regulation (PSR)
      3. 6.3.3 Primary-Side Constant Voltage Regulation
      4. 6.3.4 Primary-Side Constant Current Regulation
      5. 6.3.5 Valley-Switching and Valley-Skipping
      6. 6.3.6 Startup Operation
      7. 6.3.7 Fault Protection
    4. 6.4 Device Functional Modes
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 Input Bulk Capacitance and Minimum Bulk Voltage
        2. 7.2.2.2 Transformer Turns Ratio, Inductance, Primary-Peak Current
        3. 7.2.2.3 Transformer Parameter Verification
        4. 7.2.2.4 Output Capacitance
        5. 7.2.2.5 VDD Capacitance, CVDD
        6. 7.2.2.6 VS Resistor Divider, Line Compensation, and Cable Compensation
      3. 7.2.3 Application Curves
    3. 7.3 Do's and Don'ts
    4. 7.4 Power Supply Recommendations
    5. 7.5 Layout
      1. 7.5.1 Layout Guidelines
      2. 7.5.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
      1. 8.1.1 Device Nomenclature
        1. 8.1.1.1  Capacitance Terms in Farads
        2. 8.1.1.2  Duty-Cycle Terms
        3. 8.1.1.3  Frequency Terms in Hertz
        4. 8.1.1.4  Current Terms in Amperes
        5. 8.1.1.5  Current and Voltage Scaling Terms
        6. 8.1.1.6  Transformer Terms
        7. 8.1.1.7  Power Terms in Watts
        8. 8.1.1.8  Resistance Terms in Ω
        9. 8.1.1.9  Timing Terms in Seconds
        10. 8.1.1.10 DC Voltage Terms in Volts
        11. 8.1.1.11 AC Voltage Terms in Volts
        12. 8.1.1.12 Efficiency Terms
    2. 8.2 Documentation Support
      1. 8.2.1 Related Documentation
    3. 8.3 Receiving Notification of Documentation Updates
    4. 8.4 Support Resources
    5. 8.5 Trademarks
    6. 8.6 Electrostatic Discharge Caution
    7. 8.7 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

Pin Functions

PIN(1)I/ODESCRIPTION
NAMENO.
CBC3IThis pin programs compensation of cable voltage drop with a resistor to GND.
CS5IThe current sense input pin connects to a ground-referenced current-sense resistor in series with the power switch. The resulting voltage is used to monitor and control the peak primary current. A series resistor can be added to this pin to compensate the peak switch current levels as the rectified bulk voltage varies.
DRV6OThis pin drives the gate of an external high-voltage MOSFET switching transistor.
GND4GThis pin is both the reference pin for the controller and the low-side return for the drive output. Special care should be taken to return all AC decoupling capacitors as close as possible to this pin and avoid any common trace length with power and signal return paths.
HV8IThis pin connects directly to the rectified bulk voltage and provides charge to the VDD capacitor for start-up of the power supply.
VDD1PThis pin supplies biased input to the controller and requires a carefully-placed bypass capacitor to GND.
VS2IThis pin provides voltage feed-back and demagnetization timing to the controller. This pin facilitates output voltage regulation, frequency limiting, constant-current control, line voltage detection, and output overvoltage detection. Connect this pin to a voltage divider between an auxiliary winding and GND. The value of the high-side resistor of this divider is used to program the AC-mains run and stop thresholds and line compensation at the CS pin.
(1) P = Power, G = Ground, I = Input, O = Output, I/O = Input/Output