SLUSF78A June   2023  – November 2024 UCC28731-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
    1.     Pin Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Detailed Pin Description
        1. 6.3.1.1 VDD (Device Bias Voltage Supply)
        2. 6.3.1.2 GND (Ground)
        3. 6.3.1.3 HV (High Voltage Startup)
        4. 6.3.1.4 DRV (Gate Drive)
        5. 6.3.1.5 CBC (Cable Compensation)
        6. 6.3.1.6 VS (Voltage Sense)
        7. 6.3.1.7 CS (Current Sense)
      2. 6.3.2 Primary-Side Regulation (PSR)
      3. 6.3.3 Primary-Side Constant Voltage Regulation
      4. 6.3.4 Primary-Side Constant Current Regulation
      5. 6.3.5 Valley-Switching and Valley-Skipping
      6. 6.3.6 Startup Operation
      7. 6.3.7 Fault Protection
    4. 6.4 Device Functional Modes
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 Input Bulk Capacitance and Minimum Bulk Voltage
        2. 7.2.2.2 Transformer Turns Ratio, Inductance, Primary-Peak Current
        3. 7.2.2.3 Transformer Parameter Verification
        4. 7.2.2.4 Output Capacitance
        5. 7.2.2.5 VDD Capacitance, CVDD
        6. 7.2.2.6 VS Resistor Divider, Line Compensation, and Cable Compensation
      3. 7.2.3 Application Curves
    3. 7.3 Do's and Don'ts
    4. 7.4 Power Supply Recommendations
    5. 7.5 Layout
      1. 7.5.1 Layout Guidelines
      2. 7.5.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
      1. 8.1.1 Device Nomenclature
        1. 8.1.1.1  Capacitance Terms in Farads
        2. 8.1.1.2  Duty-Cycle Terms
        3. 8.1.1.3  Frequency Terms in Hertz
        4. 8.1.1.4  Current Terms in Amperes
        5. 8.1.1.5  Current and Voltage Scaling Terms
        6. 8.1.1.6  Transformer Terms
        7. 8.1.1.7  Power Terms in Watts
        8. 8.1.1.8  Resistance Terms in Ω
        9. 8.1.1.9  Timing Terms in Seconds
        10. 8.1.1.10 DC Voltage Terms in Volts
        11. 8.1.1.11 AC Voltage Terms in Volts
        12. 8.1.1.12 Efficiency Terms
    2. 8.2 Documentation Support
      1. 8.2.1 Related Documentation
    3. 8.3 Receiving Notification of Documentation Updates
    4. 8.4 Support Resources
    5. 8.5 Trademarks
    6. 8.6 Electrostatic Discharge Caution
    7. 8.7 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

7.4 Power Supply Recommendations

The UCC28731-Q1 is intended for DC-to-DC converters using flyback toplogy in automotive systems like backsup supply in high voltage traction inverter, or On-Board Charger (OBC). It can also be used in other applications and converter topologies with different input voltages. Be sure that all voltages and currents are within the recommended operating conditions and absolute maximum ratings of the device.

The DRV output normally begins PWM pulses approximately 55µs after VDD exceeds the turn-on threshold VVDD(on). Avoid excessive dv/dt on VDD. Positive dv/dt greater than 1V/µs may delay the start of PWM . Negative dv/dt greater than 1V/µs on VDD which does not fall below the UVLO turn-off threshold VVDD(off) may result in a temporary dip in the output voltage.