SLVAF85 September   2026 TPS2596 , TPS25961

 

  1.   1
  2.   Abstract
  3.   Trademarks
  4. 1Introduction
  5. 2Conventional RC Circuit-Based Design
  6. 3Proposed Design with eFuse
  7. 4Comparison Summary and Conclusion
  8. 5References

Proposed Design with eFuse

 Block Diagram of EFuse-Based DesignFigure 3-1 Block Diagram of EFuse-Based Design

As shown in Figure 3-1, the proposed design replaces the RLIM resistor with an eFuse. Unlike the conventional RC-based design where the supply current is limited by RLIM, the eFuse allows the current limit to be programmed through the ILIM pin. A higher current limit enables the power supply to deliver more energy during latching, thereby reducing the required hold-up capacitance.

The required hold-up capacitance can be calculated using Equation 2:

Equation 2. Chold_up_new=tpulseRc×lnVin-ilim×RcVmin-ilim×Rc

In a typical single phase smart e-meter:

  • Nominal supply voltage = 12V
  • Relay coil resistance = 96/2 = 48Ω
  • Pulse duration = 50ms
  • Relay operating voltage range = 12V to 8.4V

A 1.5mF hold-up capacitor is required for successful latching under the above typical operating conditions, as calculated using Equation 2.

The minimum hold-up capacitance required at various eFuse current-limit settings was calculated, and the corresponding test results are shown in Figure 3-2 to Figure 3-4.

 Test Result of Fixed ILIM =
                    120mA with 1.48mF of Hold-Up Capacitor Figure 3-2 Test Result of Fixed ILIM = 120mA with 1.48mF of Hold-Up Capacitor
 Test Result of Fixed ILIM =
                    150mA with 1.16mF of Hold-Up Capacitor Figure 3-3 Test Result of Fixed ILIM = 150mA with 1.16mF of Hold-Up Capacitor
 Test Result of Fixed ILIM =
                    180mA with 0.69mF of Hold-Up Capacitor Figure 3-4 Test Result of Fixed ILIM = 180mA with 0.69mF of Hold-Up Capacitor

The test results in Figure 3-2 to Figure 3-4 show that increasing the current limit reduces the required hold-up capacitance. Therefore, the capacitor size is primarily determined by the current limit during the latching phase.

A dynamic current limit method can further optimize both capacitor size and power consumption by configuring a higher current limit during latching and a lower limit during steady-state operation. This allows the SMPS to provide maximum available energy during latching while reducing the steady current during steady state. The dynamic current implementation is described below and shown in Figure 3-5.

Implementation of dynamic current limit:

  • Current-limit configuration: The ILIM pin is connected to RILIM_startup and RILIM_pulse, with an N-channel MOSFET used to switch between the two current-limit settings.
  • During latching: Upon receiving a relay-latching command, the microcontroller turns ON the N-channel MOSFET, enabling RILIM_pulse and setting the eFuse to the higher current limit.
  • After latching: The microcontroller turns OFF the MOSFET, disabling RILIM_pulse and returning the eFuse to the lower current limit set by RILIM_startup.
 Design Using Dynamic Current
                    Limit Feature Circuit of eFuse Figure 3-5 Design Using Dynamic Current Limit Feature Circuit of eFuse

The dynamic current-limiting tests were performed with the lower current limit fixed at 120mA and different higher current-limit values. A 5V DC gate signal was applied to the N-channel MOSFET for 50ms to enable the higher current limit. After 50ms, the current limit returned to 120mA in each test. The corresponding test results are shown in Figure 3-6 and Figure 3-7.

 Test Result of Dynamic ILIM =
                    150mA with 1.16mF of Hold-Up Capacitor Figure 3-6 Test Result of Dynamic ILIM = 150mA with 1.16mF of Hold-Up Capacitor
 Test Result of Dynamic ILIM =
                    180mA with 0.69mF of Hold-Up Capacitor Figure 3-7 Test Result of Dynamic ILIM = 180mA with 0.69mF of Hold-Up Capacitor

Consider the implementation circuit corresponding to the test results shown in Figure 3-7. The inrush current limit is set to 120mA, while the latching-phase current limit is set to 180mA. With dynamic current limiting, the required hold-up capacitor is 0.69mF, compared with 3.3mF used in the conventional non-eFuse design.