SLVSIP6 June   2026 LMK6L-Q1

ADVMIX  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Environmental Compliance
    4. 6.4 Recommended Operating Conditions
    5. 6.5 Thermal Information
    6. 6.6 Electrical Characteristics
    7. 6.7 Timing Diagrams
    8. 6.8 Typical Characteristics
  8. 7 Parameter Measurement Information
    1. 7.1 Device Output Configurations
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Bulk Acoustic Wave (BAW)
      2. 8.3.2 Device Block-Level Description
      3. 8.3.3 Function Pins
        1. 8.3.3.1 FSEL Implementation
      4. 8.3.4 Output Terminations
        1. 8.3.4.1 Replacing a LVPECL oscillator with the LMK6L-Q1
        2. 8.3.4.2 Replacing a HCSL OSC With the LMK6L-Q1
      5. 8.3.5 Wettable Flanks
    4. 8.4 Device Functional Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
        1. 9.2.3.1 LVDS Phase Noise Curves
        2. 9.2.3.2 HS-LVDS 1.2Vppd Phase Noise Curves
        3. 9.2.3.3 AC-LVPECL 1.2Vppd Phase Noise Curves
        4. 9.2.3.4 LP-HCSL Phase Noise Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
        1. 9.4.1.1 Providing Thermal Reliability
        2. 9.4.1.2 Recommended Solder Reflow Profile
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Mechanical Data

9.3 Power Supply Recommendations

For the best electrical performance of the LMK6L-Q1, TI recommends using 0.1µF and 1µF capacitor on the device power supply bypass network. Place these capacitors as close as possible to the supply pins. TI also recommends using component side mounting of the power supply bypass capacitors and use 0201 body size for the 0.1µF capacitor and 0603 body size for the 1µF capacitor to facilitate signal routing. Keep the connections between the bypass capacitors and the power supply on the device as short as possible. Ground the other side of the capacitor using a low impedance connection to the ground plane.