Inicio Circuitos integrados de gestión de baterías CI para cargador de batería
Inicio
Circuitos integrados de gestión de baterías
CI para cargador de batería
NUEVO

BQ25996

ACTIVO

Batería I2C en paralelo con condensadores conmutados, controlada, de una sola celda, 4:1, 16 A

Haga su pedido ahora
Hoja de datos

BQ25996

ACTIVO
Hoja de datos Haga su pedido ahora

Detalles del producto

Rating Catalog Number of series cells 1 Cell chemistry Li-Ion/Li-Polymer, Lithium Phosphate/LiFePO4 Charge current (max) (A) 16.2 Features Input OVP, Integrated ADC Vin (min) (V) 6 Vin (max) (V) 22 Absolute max Vin (max) (V) 40 Control topology Flash Charger Battery charge voltage (min) (V) 3 Battery charge voltage (max) (V) 4.65 Control interface I2C Operating temperature range (°C) -40 to 85
Rating Catalog Number of series cells 1 Cell chemistry Li-Ion/Li-Polymer, Lithium Phosphate/LiFePO4 Charge current (max) (A) 16.2 Features Input OVP, Integrated ADC Vin (min) (V) 6 Vin (max) (V) 22 Absolute max Vin (max) (V) 40 Control topology Flash Charger Battery charge voltage (min) (V) 3 Battery charge voltage (max) (V) 4.65 Control interface I2C Operating temperature range (°C) -40 to 85
DSBGA (YFF) 80 13.006845 mm² 4.071 x 3.195
  • 98.3% peak efficiency switched cap parallel charger supporting 1-cell battery and 16A fast charge
  • Switched cap architecture with selectable and bi-directional 4:1, 3:1, 2:1 and 1:1 conversion ratios
  • Provide gate drive signal for ACFET gate drive
  • Low Power Mode pin for <5µA standby bias current
  • Support wide range of input voltage

    • Up to 22V operational input voltage

    • Maximum 40V input voltage with optional external ACFET and 28V without external ACFET

  • Integrated programmable protection features for safe operation
    • Input over-voltage protections (VAC_OVP and VBUS_OVP) with external ACFET up to 40V
    • Battery over-voltage protection (VBAT_OVP)
    • Input over-current protection (IBUS_OCP)
    • Output over-voltage protection (VOUT_OVP) and over-current protection (IBAT_OCP)
    • Input under-current protection (IBUS_UCP) to detect adapter unplug and prevent boost-back
    • Input and output short-circuit protections (IBUS_RCP and IBUS_SCP)
    • Junction over-temperature protection (TDIE_FLT)
  • Programmable settings for system optimization
    • Interrupts and interrupt masks
    • ADC readings and configuration
  • Integrated 16-bit ADC for voltage, current and temperature monitoring
  • 98.3% peak efficiency switched cap parallel charger supporting 1-cell battery and 16A fast charge
  • Switched cap architecture with selectable and bi-directional 4:1, 3:1, 2:1 and 1:1 conversion ratios
  • Provide gate drive signal for ACFET gate drive
  • Low Power Mode pin for <5µA standby bias current
  • Support wide range of input voltage

    • Up to 22V operational input voltage

    • Maximum 40V input voltage with optional external ACFET and 28V without external ACFET

  • Integrated programmable protection features for safe operation
    • Input over-voltage protections (VAC_OVP and VBUS_OVP) with external ACFET up to 40V
    • Battery over-voltage protection (VBAT_OVP)
    • Input over-current protection (IBUS_OCP)
    • Output over-voltage protection (VOUT_OVP) and over-current protection (IBAT_OCP)
    • Input under-current protection (IBUS_UCP) to detect adapter unplug and prevent boost-back
    • Input and output short-circuit protections (IBUS_RCP and IBUS_SCP)
    • Junction over-temperature protection (TDIE_FLT)
  • Programmable settings for system optimization
    • Interrupts and interrupt masks
    • ADC readings and configuration
  • Integrated 16-bit ADC for voltage, current and temperature monitoring

The BQ25996 is a 98.3% peak efficiency, 16A battery charging solution using dual-phase switched cap architecture for 1-cell Li-ion battery. The switched cap architecture allows the cable current to be one quarter, one third, or one half of the charging current depending on converter mode and input voltage, reducing the cable power loss and limiting temperature rise. The dual-phase architecture increases charging efficiency and reduces the input and output cap requirements. When used with a main charger such as BQ25790, the system enables the fast charging at the very low power loss from pre-charge through constant current (CC), constant voltage (CV), and termination.

The BQ25996 also supports bypass mode charge through internal MOSFETs.

The device supports control and driver for external N-FETs or a single N-FET relative to a CMSRC regulation pin.

The BQ25996 is a 98.3% peak efficiency, 16A battery charging solution using dual-phase switched cap architecture for 1-cell Li-ion battery. The switched cap architecture allows the cable current to be one quarter, one third, or one half of the charging current depending on converter mode and input voltage, reducing the cable power loss and limiting temperature rise. The dual-phase architecture increases charging efficiency and reduces the input and output cap requirements. When used with a main charger such as BQ25790, the system enables the fast charging at the very low power loss from pre-charge through constant current (CC), constant voltage (CV), and termination.

The BQ25996 also supports bypass mode charge through internal MOSFETs.

The device supports control and driver for external N-FETs or a single N-FET relative to a CMSRC regulation pin.
filter Buscar otro/a CI para cargador de batería
Descargar Ver vídeo con transcripción Video
Solicitar más información

La hoja de datos completa está disponible. Solicitar ahora

Documentación técnica

star =Principal documentación para este producto seleccionada por TI
No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 1
Documentación principal Tipo Título Opciones de formato Fecha
* Data sheet BQ25996 I2 C Controlled 1-Cell 16A Switched Cap Parallel Battery Charger datasheet PDF | HTML 10 jun 2026

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Encapsulado Pines Símbolos CAD, huellas y modelos 3D
DSBGA (YFF) 80 Ultra Librarian
Se aplican los Términos y condiciones estándar de TI para los elementos de evaluación.

Pedidos y calidad

Información incluida:
  • RoHS
  • REACH
  • Marcado del dispositivo
  • Acabado de plomo/material de la bola
  • Clasificación de nivel de sensibilidad a la humedad (MSL)/reflujo máximo
  • Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
  • Contenido del material
  • Resumen de calificaciones
  • Monitoreo continuo de confiabilidad
Información incluida:
  • Lugar de fabricación
  • Lugar de ensamblaje

Los productos recomendados pueden tener parámetros, módulos de evaluación o diseños de referencia relacionados con este producto de TI.

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

Ver todos los temas del foro en inglés

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene alguna pregunta sobre calidad, encapsulados o pedido de productos de TI, consulte el servicio de asistencia de TI. ​​​​​​​​​​​​​​

Videos