SN74AVC16244

ACTIVO

Búferes de 16 canales, 1.4 V a 3.6 V con salidas de 3 estados

Haga su pedido ahora

Hoja de datos

document-pdfAcrobat SN74AVC16244 datasheet (Rev. N) (Inglés)

SN74AVC16244

ACTIVO

Hoja de datos

Haga su pedido ahora

Detalles del producto

Technology family

AVC

Number of channels

16

IOL (max) (mA)

12

Supply current (max) (µA)

40

IOH (max) (mA)

-12

Input type

Standard CMOS

Output type

3-State

Features

Balanced outputs, Over-voltage tolerant inputs, Partial power down (Ioff), Ultra high speed (tpd <5ns)

Rating

Catalog

Operating temperature range (°C)

-40 to 85

Technology family

AVC

Number of channels

16

IOL (max) (mA)

12

Supply current (max) (µA)

40

IOH (max) (mA)

-12

Input type

Standard CMOS

Output type

3-State

Features

Balanced outputs, Over-voltage tolerant inputs, Partial power down (Ioff), Ultra high speed (tpd <5ns)

Rating

Catalog

Operating temperature range (°C)

-40 to 85

TVSOP (DGV)

48

62.08 mm² (9.7 mm × 6.4 mm)

TSSOP (DGG)

48

101.25 mm² (12.5 mm × 8.1 mm)

Member of the Texas Instruments Widebus™ Family
DOC™ (Dynamic Output Control) Circuit Dynamically Changes Output Impedance, Resulting in Noise Reduction Without Speed Degradation
Less Than 2-ns Maximum Propagation Delay at 2.5-V and 3.3-V V_CC
Dynamic Drive Capability Is Equivalent to Standard Outputs With I_OH and I_OL of ±24 mA at 2.5-V V_CC
Overvoltage-Tolerant Inputs/Outputs Allow Mixed-Voltage-Mode Data Communications
I_off Supports Partial-Power-Down Mode Operation
Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
ESD Protection Exceeds JESD 22
- 2000-V Human-Body Model (A114-A)
- 200-V Machine Model (A115-A)

DOC and Widebus are trademarks of Texas Instruments.

Member of the Texas Instruments Widebus™ Family
DOC™ (Dynamic Output Control) Circuit Dynamically Changes Output Impedance, Resulting in Noise Reduction Without Speed Degradation
Less Than 2-ns Maximum Propagation Delay at 2.5-V and 3.3-V V_CC
Dynamic Drive Capability Is Equivalent to Standard Outputs With I_OH and I_OL of ±24 mA at 2.5-V V_CC
Overvoltage-Tolerant Inputs/Outputs Allow Mixed-Voltage-Mode Data Communications
I_off Supports Partial-Power-Down Mode Operation
Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
ESD Protection Exceeds JESD 22
- 2000-V Human-Body Model (A114-A)
- 200-V Machine Model (A115-A)

DOC and Widebus are trademarks of Texas Instruments.

A Dynamic Output Control (DOC) circuit is implemented, which, during the transition, initially lowers the output impedance to effectively drive the load and, subsequently, raises the impedance to reduce noise. Figure 1 shows typical V_OL vs I_OL and V_OH vs I_OH curves to illustrate the output impedance and drive capability of the circuit. At the beginning of the signal transition, the DOC circuit provides a maximum dynamic drive that is equivalent to a high-drive standard-output device. For more information, refer to the TI application reports, AVC Logic Family Technology and Applications, literature number SCEA006, and Dynamic Output Control (DOC^TM) Circuitry Technology and Applications, literature number SCEA009.

This 16-bit buffer/driver is operational at 1.2-V to 3.6-V V_CC, but is designed specifically for 1.65-V to 3.6-V V_CC operation.

The SN74AVC16244 is designed specifically to improve the performance and density of 3-state memory address drivers, clock drivers, and bus-oriented receivers and transmitters.

The device can be used as four 4-bit buffers, two 8-bit buffers, or one 16-bit buffer. It provides true outputs and symmetrical active-low output-enable (OE\) inputs.

This device is fully specified for partial-power-down applications using I_off. The I_off circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

To ensure the high-impedance state during power up or power down, OE\ should be tied to V_CC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

A Dynamic Output Control (DOC) circuit is implemented, which, during the transition, initially lowers the output impedance to effectively drive the load and, subsequently, raises the impedance to reduce noise. Figure 1 shows typical V_OL vs I_OL and V_OH vs I_OH curves to illustrate the output impedance and drive capability of the circuit. At the beginning of the signal transition, the DOC circuit provides a maximum dynamic drive that is equivalent to a high-drive standard-output device. For more information, refer to the TI application reports, AVC Logic Family Technology and Applications, literature number SCEA006, and Dynamic Output Control (DOC^TM) Circuitry Technology and Applications, literature number SCEA009.

This 16-bit buffer/driver is operational at 1.2-V to 3.6-V V_CC, but is designed specifically for 1.65-V to 3.6-V V_CC operation.

The SN74AVC16244 is designed specifically to improve the performance and density of 3-state memory address drivers, clock drivers, and bus-oriented receivers and transmitters.

The device can be used as four 4-bit buffers, two 8-bit buffers, or one 16-bit buffer. It provides true outputs and symmetrical active-low output-enable (OE\) inputs.

This device is fully specified for partial-power-down applications using I_off. The I_off circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

To ensure the high-impedance state during power up or power down, OE\ should be tied to V_CC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

filter

Buscar otro/a Búferes y controladores no inversores

Descargar Ver vídeo con transcripción Video

Productos similares que pueden interesarle

open-in-new

Comparar alternativas

Pin por pin con la misma funcionalidad que el dispositivo comparado

SN74AUC16240

ACTIVO

Inversores de alta velocidad, de 16 canales, 0.8 V a 2.7 V con salidas de 3 estados Voltage range 0.8V to 2.7V, average propagation delay 1.7ns, average drive strength 9mA

SN74AUC16244

ACTIVO

Búferes de alta velocidad, de 16 canales, 0.8 V a 2.7 V con salidas de 3 estados Voltage range 0.8V to 2.7V, average propagation delay 1.7ns, average drive strength 9mA

SN74AUCH16244

ACTIVO

Búferes de alta velocidad de 16 canales, 0.8 V a 2.7 V, con retención de bus y salidas de 3 estados Voltage range 0.8V to 2.7V, average propagation delay 1.7ns, average drive strength 9mA

SN74ALVCH16244

ACTIVO

Búferes de 16 canales, 1.65 V a 3.6 V con retención de bus y salidas de 3 estados Voltage range 1.65V to 3.6V, average propagation delay 3ns, average drive strength 24mA

Documentación técnica

No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.

Ver todo 2

Documentación principal	Tipo	Título	Opciones de formato	Descargar la versión más reciente en inglés	Fecha
*	Hoja de datos	SN74AVC16244 datasheet (Rev. N)			21/07/2004
	Nota sobre la aplicación	Simultaneous-Switching Performance of TI Logic Devices (Rev. B)			23/02/2005

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Modelo de simulación