驅動程式或資料庫
AFE79XX-HSC-DESIGN — AFE79xx family high-speed transceiver design & support files
Find detailed product information on the AFE79xx product family (datasheets, EVM resources, software and firmware, reference designs, etc)
產品規格表
AFE7950-SP
- Request full data sheet
- Radiation hardness assured AFE7950-SP:
- Single-event latch up (SEL): 70MeV-cm2/mg
- RLAT Total ionizing dose (TID): 100krad (Si)
- Radiation tolerant AFE7950-SEP:
- Single-event latch up (SEL): 43MeV-cm2/mg
- RLAT Total ionizing dose (TID): 30krad (Si)
- Four RF sampling 12GSPS TX DACs
- Six RF sampling 3GSPS RX ADCs
- Maximum RF signal bandwidth: 1200MHz (or 2400MHz for 2TX)
- RF frequency range:
- TX: 600MHz to 12GHz
- RX: 5MHz to 12GHz
- Digital Step Attenuators (DSA):
- TX: 40dB range, 0.125dB steps
- RX or FB: 25dB range, 0.5dB steps
- Single or dual-band DUC or DDCs for TX and RX
- SerDes data interface:
- 8 SerDes transceivers up to 24.75Gbps
- JESD204B/C subclass 1 compatible
- Package: 17mm × 17mm FCBGA, 0.8mm pitch
- Screening:
- One fabrication, assembly, and test site
- Product traceability
- Extended product life cycle
- Extended product change notification
- Vendor item drawing
- Radiation lot acceptance Test (RLAT) (AFE7950-Sx only)
- Meets ASTM E595 out gassing specification (AFE7950-Sx only)
- Production burn-in (AFE7950-SP only)
The AFE7950-x is a high performance, wide bandwidth multi-channel transceiver, integrating four RF sampling transmitter chains, four RF sampling receiver chains and two RF sampling feedback chains (six RF sampling ADCs total). With operation up to 12GHz, this device enables direct RF sampling in the L, S, C and X-band frequency ranges without the need for additional frequency conversions stages. This improvement in density and flexibility enables high-channel-count, multi-mission systems.
The TX signal paths support interpolation and digital up conversion options that deliver up to 1200MHz of signal bandwidth for four TX or 2400MHz for two TX. The output of the DUCs drives a 12GSPS DAC (digital to analog converter) with a mixed mode output option to enhance 2nd Nyquist operation. The DAC output includes a variable gain amplifier (TX DSA) with 40dB range and 1dB analog and 0.125dB digital steps.
Each receiver chain includes a 25dB range Digital Step Attenuator (DSA), followed by a 3GSPS ADC (analog-to-digital converter). Each receiver channel has an analog peak power detector and various digital power detectors to assist an external or internal autonomous automatic gain controller, and RF overload detectors for device reliability protection. Flexible decimation options provide optimization of data bandwidth up to 1200MHz for four RX without FB paths or 600MHz with two FB paths (1200MHz BW each).
技術文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 14 設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
開發板
AFE7950EVM — 適用於四傳輸、六接收、X 頻段、射頻取樣 AFE 的 AFE7950 評估模組
AFE7950 系列評估模組 (EVM) 是靈活的射頻取樣收發器平台，可配置為支援最多同時四個發射、四個接收與兩個回饋 (4T4R+2FB) 通道。此 EVM 設計可介接以下所示 TI 模式/擷取卡解決方案 (分開販售) 以及許多符合 FPGA FMC 標準的開發套件。
開發板
TRF-X-AFE7950EVM — TRF1213 和 AFE7950 評估模組
TRF-X-AFE7950EVM 評估模組用於評估 TI AFE79xx 系列整合式 RF 取樣收發器的性能，其 RX 配置 TI TRF1213 單端轉差分 (S2D) 放大器。TRF-X-AFE7950EVM 專門使用 AFE7950 收發器。AFE79xx 裝置支援最多四發射通道、四接收通道及兩回饋通道 (4T4R2F)，並整合用於產生資料轉換器時鐘的鎖相迴路 (PLL) 及電壓控制振盪器 (VCO)。AFE79xx 整合八個 JESD204B 及 JESD204C 相容的串聯器或解串器 (SerDes) 收發器。這些收發器可透過板載 FPGA 夾層介面卡 (FMC) 連接器，以最高 (...)
參考設計
TIDA-010260 — 4T5R 航太級整合式收發器參考設計
4T5R 航太級整合式收發器參考設計整合了完整的 RF 取樣收發器，包括時脈解決方案和電源解決方案。此設計在 VITA-57 規格內整合了所有 -SEP 型 TI 裝置和符合航太標準的被動元件。
Design guide: PDF
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| FCBGA (ALK) | 400 | Ultra Librarian |
訂購與品質
內含資訊：
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中的可靠性監測
內含資訊：
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。