首頁 電池管理 IC 電池充電器 IC
首頁
電池管理 IC
電池充電器 IC

BQ25125

現行

適用於穿戴式裝置和物聯網的低 IQ 高度整合電池充電管理解決方案

立即訂購
產品規格表

BQ25125

現行
產品規格表 立即訂購

產品詳細資料

Rating Catalog Number of series cells 1 Cell chemistry Li-Ion/Li-Polymer Charge current (max) (A) 0.3 Features BAT temp thermistor monitoring (JEITA profile), IC thermal regulation, Input OVP, Integrated LDO, Integrated buck converter, Power Path Vin (min) (V) 3.4 Vin (max) (V) 5.5 Absolute max Vin (max) (V) 20 Control topology Linear Battery charge voltage (min) (V) 3.6 Battery charge voltage (max) (V) 4.65 Control interface I2C Operating temperature range (°C) -40 to 85
Rating Catalog Number of series cells 1 Cell chemistry Li-Ion/Li-Polymer Charge current (max) (A) 0.3 Features BAT temp thermistor monitoring (JEITA profile), IC thermal regulation, Input OVP, Integrated LDO, Integrated buck converter, Power Path Vin (min) (V) 3.4 Vin (max) (V) 5.5 Absolute max Vin (max) (V) 20 Control topology Linear Battery charge voltage (min) (V) 3.6 Battery charge voltage (max) (V) 4.65 Control interface I2C Operating temperature range (°C) -40 to 85
DSBGA (YFP) 25 6.75999999999999792000000000000016 mm² (— mm × — mm)
  • Increases system operation time between charges
    • Configurable 300-mA buck regulator (1.8 V default)
    • 700-nA (typical) Iq with buck converter enabled (No Load)
    • Configurable load switch or 100-mA LDO output (1.8 V default)
    • Up to 300-mA charge current for fast charging
    • 0.5% Accurate battery voltage regulation (configurable from 3.6 V to 4.65 V in 10-mV steps)
    • Configurable termination current down to 500 µA
    • Simple voltage based battery monitor
    • Watchdog timer enabled by default
    • VDPPM Loop disabled
    • VINDPM Disabled by default to support low voltage charging
  • Highly integrated solution with small footprint
    • 2.5 mm x 2.5 mm WCSP Package and 6 external components for minimal solution
    • Push-button wake-up and reset with adjustable timers
    • Power path management for powering the system and charging the battery
    • Power path management enables <50 nA ship mode battery quiescent current for longest shelf life
    • Battery charger operates from 3.4 V – 5.5 VIN (5.5-V OVP / 20-V tolerant)
    • Dedicated pins for input current limit, charge current, termination current, and status output
  • I2C Communication control
    • Charge voltage and current
    • Termination threshold
    • Input current limit
    • VINDPM Threshold
    • Timer options
    • Load switch control
    • Controls for interrupts for faults and status
    • System output voltage adjustment
    • LDO Output voltage adjustment
  • Safety-Related Certification:
    • TUV IEC 62368-1 Certification
  • Increases system operation time between charges
    • Configurable 300-mA buck regulator (1.8 V default)
    • 700-nA (typical) Iq with buck converter enabled (No Load)
    • Configurable load switch or 100-mA LDO output (1.8 V default)
    • Up to 300-mA charge current for fast charging
    • 0.5% Accurate battery voltage regulation (configurable from 3.6 V to 4.65 V in 10-mV steps)
    • Configurable termination current down to 500 µA
    • Simple voltage based battery monitor
    • Watchdog timer enabled by default
    • VDPPM Loop disabled
    • VINDPM Disabled by default to support low voltage charging
  • Highly integrated solution with small footprint
    • 2.5 mm x 2.5 mm WCSP Package and 6 external components for minimal solution
    • Push-button wake-up and reset with adjustable timers
    • Power path management for powering the system and charging the battery
    • Power path management enables <50 nA ship mode battery quiescent current for longest shelf life
    • Battery charger operates from 3.4 V – 5.5 VIN (5.5-V OVP / 20-V tolerant)
    • Dedicated pins for input current limit, charge current, termination current, and status output
  • I2C Communication control
    • Charge voltage and current
    • Termination threshold
    • Input current limit
    • VINDPM Threshold
    • Timer options
    • Load switch control
    • Controls for interrupts for faults and status
    • System output voltage adjustment
    • LDO Output voltage adjustment
  • Safety-Related Certification:
    • TUV IEC 62368-1 Certification

The BQ25125 is a highly integrated battery charge management IC that integrates the most common functions for wearable devices: Linear charger, regulated output, load switch, manual reset with timer, and battery voltage monitor. The integrated buck converter is a high efficiency, low IQ switcher using DCS-Control™ that extends light load efficiency down to 10-µA load currents.

The low quiescent current during operation and shutdown enables maximum battery life. The device supports charge currents from 5 mA to 300 mA. The input current limit, charge current, buck converter output voltage, LDO output voltage, and other parameters are programmable through the I2C interface.

The battery is charged using a standard Li-Ion charge profile with three phases: precharge, constant current and constant voltage. A voltage-based JEITA compatible battery pack thermistor monitoring input (TS) is included that monitors battery temperature and automatically changes charge parameters to prevent the battery from charging outside of its safe temperature range. The charger is optimized for 5-V USB input, with 20-V tolerance to withstand line transients. The buck converter is run from the input or battery. When in battery only mode, the device can run from a battery up to 4.65 V.

A configurable load switch allows system optimization by disconnecting infrequently used devices. The manual reset with timer allows multiple different configuration options for wake are reset optimization. A simple voltage based monitor provides battery level information to the host in 2% increments from 60% to 100% of the programmed V(BATREG).

The BQ25125 is a highly integrated battery charge management IC that integrates the most common functions for wearable devices: Linear charger, regulated output, load switch, manual reset with timer, and battery voltage monitor. The integrated buck converter is a high efficiency, low IQ switcher using DCS-Control™ that extends light load efficiency down to 10-µA load currents.

The low quiescent current during operation and shutdown enables maximum battery life. The device supports charge currents from 5 mA to 300 mA. The input current limit, charge current, buck converter output voltage, LDO output voltage, and other parameters are programmable through the I2C interface.

The battery is charged using a standard Li-Ion charge profile with three phases: precharge, constant current and constant voltage. A voltage-based JEITA compatible battery pack thermistor monitoring input (TS) is included that monitors battery temperature and automatically changes charge parameters to prevent the battery from charging outside of its safe temperature range. The charger is optimized for 5-V USB input, with 20-V tolerance to withstand line transients. The buck converter is run from the input or battery. When in battery only mode, the device can run from a battery up to 4.65 V.

A configurable load switch allows system optimization by disconnecting infrequently used devices. The manual reset with timer allows multiple different configuration options for wake are reset optimization. A simple voltage based monitor provides battery level information to the host in 2% increments from 60% to 100% of the programmed V(BATREG).
filter 尋找其它 電池充電器 IC
下載 觀看有字幕稿的影片 影片

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 7
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 BQ25125 Low IQ Highly Integrated Battery Charge Management Solution For Wearables and IoT datasheet (Rev. A) PDF | HTML 2021/1/20
技術文章 3 ways low-Iq technologies extend battery life without compromising system performance PDF | HTML 2024/1/5
應用說明 Implementing 2-V Charge Inhibition PDF | HTML 2023/5/31
白皮書 克服低功耗應用中的低 IQ 挑戰 (Rev. B) PDF | HTML Download English Version (Rev.B) PDF | HTML 2023/4/19
應用說明 BQ2512x Frequently Asked Questions 2021/11/22
技術文章 When to use rechargeable batteries in small battery applications PDF | HTML 2019/10/1
技術文章 Pull the tab: How to implement ship mode in your lithium-ion battery design PDF | HTML 2019/2/20

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

BQ25120AEVM — 適用於穿戴式裝置和耳戴式裝置的 700nA 低 IQ 高度整合式電池充電管理評估模組

bq25120AEVM 評估模組是高度整合式電池充電管理 IC，其中整合了穿戴式裝置最常見的功能：線性充電器、穩壓輸出、負載開關、計時器手動重設與電池電壓監控。運作和關機期間的低靜態電流可最大限度延長電池使用壽命。本裝置支援從 5mA 至 300mA 的充電電流。輸入電流限制、充電電流、PWM 輸出電壓、LDO 輸出電壓和其它參數可透過 I2C 介面進行程式化。該電池採用具有三相位的標準鋰離子充電曲線充電：預充電、恆流和恆壓。
使用指南: PDF
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
介面轉接器

EV2400 — 適用電池電量 (氣量) 計評估模組的 USB PC 介面板

The EV2400 EVM interface board enables an IBM-compatible or other type PC (with the required driver for its particular platform) to communicate with the Texas Instruments SMBus or I2C interface gas gauges via a Universal Serial Bus (USB) port. In addition to this board, PC software is required to (...)

使用指南: PDF
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
計算工具

SLURAY9 — BQ25125 Setup Guide Tool

支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
DSBGA (YFP) 25 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片