首頁 電池管理 IC 電池充電器 IC
首頁
電池管理 IC
電池充電器 IC
最新

BQ25996

現行

I²C controlled single-cell 4:1 16A switched capacitor parallel battery charger

立即訂購
產品規格表

BQ25996

現行
產品規格表 立即訂購

產品詳細資料

Rating Catalog Number of series cells 1 Cell chemistry Li-Ion/Li-Polymer, Lithium Phosphate/LiFePO4 Charge current (max) (A) 16.2 Features Input OVP, Integrated ADC Vin (min) (V) 6 Vin (max) (V) 22 Absolute max Vin (max) (V) 40 Control topology Flash Charger Battery charge voltage (min) (V) 3 Battery charge voltage (max) (V) 4.65 Control interface I2C Operating temperature range (°C) -40 to 85
Rating Catalog Number of series cells 1 Cell chemistry Li-Ion/Li-Polymer, Lithium Phosphate/LiFePO4 Charge current (max) (A) 16.2 Features Input OVP, Integrated ADC Vin (min) (V) 6 Vin (max) (V) 22 Absolute max Vin (max) (V) 40 Control topology Flash Charger Battery charge voltage (min) (V) 3 Battery charge voltage (max) (V) 4.65 Control interface I2C Operating temperature range (°C) -40 to 85
DSBGA (YFF) 80 13.006845 mm² (4.071 mm × 3.195 mm)
  • 98.3% peak efficiency switched cap parallel charger supporting 1-cell battery and 16A fast charge
  • Switched cap architecture with selectable and bi-directional 4:1, 3:1, 2:1 and 1:1 conversion ratios
  • Provide gate drive signal for ACFET gate drive
  • Low Power Mode pin for <5µA standby bias current
  • Support wide range of input voltage

    • Up to 22V operational input voltage

    • Maximum 40V input voltage with optional external ACFET and 28V without external ACFET

  • Integrated programmable protection features for safe operation
    • Input over-voltage protections (VAC_OVP and VBUS_OVP) with external ACFET up to 40V
    • Battery over-voltage protection (VBAT_OVP)
    • Input over-current protection (IBUS_OCP)
    • Output over-voltage protection (VOUT_OVP) and over-current protection (IBAT_OCP)
    • Input under-current protection (IBUS_UCP) to detect adapter unplug and prevent boost-back
    • Input and output short-circuit protections (IBUS_RCP and IBUS_SCP)
    • Junction over-temperature protection (TDIE_FLT)
  • Programmable settings for system optimization
    • Interrupts and interrupt masks
    • ADC readings and configuration
  • Integrated 16-bit ADC for voltage, current and temperature monitoring
  • 98.3% peak efficiency switched cap parallel charger supporting 1-cell battery and 16A fast charge
  • Switched cap architecture with selectable and bi-directional 4:1, 3:1, 2:1 and 1:1 conversion ratios
  • Provide gate drive signal for ACFET gate drive
  • Low Power Mode pin for <5µA standby bias current
  • Support wide range of input voltage

    • Up to 22V operational input voltage

    • Maximum 40V input voltage with optional external ACFET and 28V without external ACFET

  • Integrated programmable protection features for safe operation
    • Input over-voltage protections (VAC_OVP and VBUS_OVP) with external ACFET up to 40V
    • Battery over-voltage protection (VBAT_OVP)
    • Input over-current protection (IBUS_OCP)
    • Output over-voltage protection (VOUT_OVP) and over-current protection (IBAT_OCP)
    • Input under-current protection (IBUS_UCP) to detect adapter unplug and prevent boost-back
    • Input and output short-circuit protections (IBUS_RCP and IBUS_SCP)
    • Junction over-temperature protection (TDIE_FLT)
  • Programmable settings for system optimization
    • Interrupts and interrupt masks
    • ADC readings and configuration
  • Integrated 16-bit ADC for voltage, current and temperature monitoring

The BQ25996 is a 98.3% peak efficiency, 16A battery charging solution using dual-phase switched cap architecture for 1-cell Li-ion battery. The switched cap architecture allows the cable current to be one quarter, one third, or one half of the charging current depending on converter mode and input voltage, reducing the cable power loss and limiting temperature rise. The dual-phase architecture increases charging efficiency and reduces the input and output cap requirements. When used with a main charger such as BQ25790, the system enables the fast charging at the very low power loss from pre-charge through constant current (CC), constant voltage (CV), and termination.

The BQ25996 also supports bypass mode charge through internal MOSFETs.

The device supports control and driver for external N-FETs or a single N-FET relative to a CMSRC regulation pin.

The BQ25996 is a 98.3% peak efficiency, 16A battery charging solution using dual-phase switched cap architecture for 1-cell Li-ion battery. The switched cap architecture allows the cable current to be one quarter, one third, or one half of the charging current depending on converter mode and input voltage, reducing the cable power loss and limiting temperature rise. The dual-phase architecture increases charging efficiency and reduces the input and output cap requirements. When used with a main charger such as BQ25790, the system enables the fast charging at the very low power loss from pre-charge through constant current (CC), constant voltage (CV), and termination.

The BQ25996 also supports bypass mode charge through internal MOSFETs.

The device supports control and driver for external N-FETs or a single N-FET relative to a CMSRC regulation pin.
filter 尋找其它 電池充電器 IC
下載 觀看有字幕稿的影片 影片
索取更多資訊

提供完整的產品規格表。立即索取

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 1
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 BQ25996 I2 C Controlled 1-Cell 16A Switched Cap Parallel Battery Charger datasheet PDF | HTML 2026/6/10

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

封裝 針腳 CAD 符號、佔位空間與 3D 模型
DSBGA (YFF) 80 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片