ISO3086T
- Meets or exceeds TIA/EIA-485-A
- Signaling rate up to 20 Mbps
- 1/8 unit load – up to 256 nodes on a bus
- Thermal shutdown protection
- Typical efficiency > 60% (I LOAD = 100 mA) - see SLUU469
- Low bus capacitance 7 pF (typical)
- 50-kV/µs typical transient immunity
- Fail-safe receiver for bus open, short, idle
- Logic inputs are 5 V tolerant
- Bus-pin ESD protection
- 11-kV HBM between bus-pins and GND2
- 6-kV HBM between bus-pins and GND1
- Safety and regulatory approvals
- 4242 V PK basic insulation per DIN EN IEC 60747-17 (VDE 0884-17)
- 2500 V RMS isolation for 1 minute per UL 1577
-
CSA component acceptance notice 5A, IEC 60950-1 and IEC 61010-1 standards
The ISO3086T is an isolated differential line transceiver with integrated oscillator outputs that provide the primary voltage for an isolation transformer. The device is a full-duplex differential line transceiver for RS-485 and RS-422 applications that can easily be configured for half-duplex operation by connecting pin 11 to pin 14, and pin 12 to pin 13.
These devices are ideal for long transmission lines since the ground loop is broken to allow for a much larger common-mode voltage range. The symmetrical isolation barrier of the device is tested to provide 4242 V PK of isolation for 1 minute per VDE between the bus-line transceiver and the logic-level interface.
Any cabled I/O can be subjected to electrical noise transients from various sources. These noise transients can cause damage to the transceiver and/or near-by sensitive circuitry if they are of sufficient magnitude and duration. These isolated devices can significantly increase protection and reduce the risk of damage to expensive control circuits.
The ISO3086T is specified for use from –40°C to 85°C.
技術文件
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
ISO1176TEVM — ISO1176T 評估模組
This document describes the ISO1176T/35T/3086T Evaluation Module (EVM). It is used to evaluate the ISO1176T PROFIBUS Transceiver, the ISO35T RS-485 transceiver, or ISO3086T RS-485 Transceiver. Because the devices are similar transceivers, and the printed-circuit board is the same for all three (...)
ISO3086TEVM — ISO3086T EVM
此文件描述 ISO1176T/35T/3086T 評估模組 (EVM)。此模組用於評估 ISO1176T PROFIBUS 收發器、ISO35T RS-485 收發器或 ISO3086T RS-485 收發器。由於這些裝置非常相似，因此所有三款 EVM 皆採用相同的印刷電路板。一本手冊即支援所有三種裝置。
EVM 可用於評估裝置參數，同時做為電路板佈局指南。此板卡允許透過 QuiteZone 連接器連接 50 歐姆同軸電纜，並提供供示波器探針使用的便利連接點，同時亦配有香蕉插孔以連接直流電源供應器。這些功能為設計人員提供了評估與成功設計最終產品所需的工具。
ISO3086TEVM-436 — ISO3086T 小型 EVM
The smaller EVM version shows the customer the space required for their design. This circuit provides an isolated, 20 Mbps, 3.3V to 5V RS-485 interface using the ISO3086T isolated RS-485 transceiver and the TPS76350 high accuracy linear regulator. This circuit achieves signal and power isolation (...)
ISO35TEVM — ISO35T 評估模組
This document describes the ISO1176T/35T/3086T Evaluation Module (EVM). It is used to evaluate the ISO1176T PROFIBUS Transceiver, the ISO35T RS-485 transceiver, or ISO3086T RS-485 Transceiver. Because the devices are similar transceivers, and the printed-circuit board is the same for all three (...)
TIDA-00058 — 20 Mbps 隔離式 RS-485 參考設計
This reference design provides an isolated, 20-Mbps, 3.3-V to 5-V RS-485 interface using the ISO3086T isolated RS-485 transceiver and the TPS76350 high-accuracy linear regulator. This circuit achieves signal and power isolation and at the same time decreases board space and power consumption.
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| SOIC (DW) | 16 | Ultra Librarian |
訂購與品質
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。