首頁 邏輯和電壓轉換 緩衝器、驅動器和收發器 通用收發器
首頁
邏輯和電壓轉換
緩衝器、驅動器和收發器
通用收發器

SN74ABTE16245

現行

具有 3 態輸出的 16 位入射波切換匯流排收發器

立即訂購
產品規格表

SN74ABTE16245

現行
產品規格表 立即訂購

產品詳細資料

Number of channels 16 IOL (max) (mA) 90 IOH (max) (mA) -90 Input type TTL Output type TTL Features Balanced outputs, Bias Vcc, Bus-hold, Over-voltage tolerant inputs, Partial power down (Ioff), Very high speed (tpd 5-10ns) Technology family ABTE Rating Catalog Operating temperature range (°C) -40 to 85
Number of channels 16 IOL (max) (mA) 90 IOH (max) (mA) -90 Input type TTL Output type TTL Features Balanced outputs, Bias Vcc, Bus-hold, Over-voltage tolerant inputs, Partial power down (Ioff), Very high speed (tpd 5-10ns) Technology family ABTE Rating Catalog Operating temperature range (°C) -40 to 85
TSSOP (DGG) 48 101.25 mm² (12.5 mm × 8.1 mm) SSOP (DL) 48 164.358 mm² (15.88 mm × 10.35 mm)
  • Members of the Texas Instruments Widebus™ Family
  • Support the VME64 ETL Specification
  • Reduced, TTL-Compatible, Input Threshold Range
  • High-Drive Outputs (IOH = –60 mA, IOL = 90 mA) Support 25- Incident-Wave Switching
  • VCC BIAS Pin Minimizes Signal Distortion During Live Insertion
  • Internal Pullup Resistor on (OE)\ Keeps Outputs in High-Impedance State During Power Up or Power Down
  • Distributed VCC and GND Pins Minimize High-Speed Switching Noise
  • Equivalent 25- Series Damping Resistor on B Port
  • Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors

Widebus is a trademark of Texas Instruments.
  • Members of the Texas Instruments Widebus™ Family
  • Support the VME64 ETL Specification
  • Reduced, TTL-Compatible, Input Threshold Range
  • High-Drive Outputs (IOH = –60 mA, IOL = 90 mA) Support 25- Incident-Wave Switching
  • VCC BIAS Pin Minimizes Signal Distortion During Live Insertion
  • Internal Pullup Resistor on (OE)\ Keeps Outputs in High-Impedance State During Power Up or Power Down
  • Distributed VCC and GND Pins Minimize High-Speed Switching Noise
  • Equivalent 25- Series Damping Resistor on B Port
  • Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors

Widebus is a trademark of Texas Instruments.

The ’ABTE16245 devices are 16-bit (dual-octal) noninverting 3-state transceivers designed for synchronous two-way communication between data buses. The control-function implementation minimizes external timing requirements. These devices can be used as two 8-bit transceivers or one 16-bit transceiver. They allow data transmission from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE)\ input can be used to disable the device so that the buses are effectively isolated. When (OE)\ is low, the device is active.

The B port has an equivalent 25- series output resistor to reduce ringing. Active bus-hold inputs also are on the B port to hold unused or floating inputs at a valid logic level.

The A port provides for the precharging of the outputs via VCCBIAS, which establishes a voltage between 1.3 V and 1.7 V when VCC is not connected.

Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended.

The ’ABTE16245 devices are 16-bit (dual-octal) noninverting 3-state transceivers designed for synchronous two-way communication between data buses. The control-function implementation minimizes external timing requirements. These devices can be used as two 8-bit transceivers or one 16-bit transceiver. They allow data transmission from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE)\ input can be used to disable the device so that the buses are effectively isolated. When (OE)\ is low, the device is active.

The B port has an equivalent 25- series output resistor to reduce ringing. Active bus-hold inputs also are on the B port to hold unused or floating inputs at a valid logic level.

The A port provides for the precharging of the outputs via VCCBIAS, which establishes a voltage between 1.3 V and 1.7 V when VCC is not connected.

Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended.
filter 尋找其它 通用收發器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
針腳對針腳的功能與所比較的裝置相同。
SN74AVC16245 現行 具有 3 態輸出的 16 位元匯流排收發器 Voltage range 0.9V to 3.6V, average propagation delay 2ns, average drive strength 12mA
SN74ALVCH16245 現行 具有 3 態輸出的 16 位元匯流排收發器 Voltage range 1.65V to 3.6V, average propagation delay 3ns, average drive strength 24mA

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 1
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 16-Bit Incident-Wave Switching Bus Transceivers With 3-State Outputs datasheet (Rev. J) 2001/12/13

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

模擬型號

SN74ABTE16245 IBIS Model (Rev. A)

SCBM063 (147 KB) - IBIS 模型
支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
TSSOP (DGG) 48 Ultra Librarian
SSOP (DL) 48 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片