支援軟體
SLDC021 — TUSS Generation III EVM GUI
支援產品和硬體
產品
超音波感測器 AFE
硬體開發
開發板
- BOOSTXL-TUSS4440 — 具有 LDO 的 TUSS4440 變壓器驅動超音波轉換器評估模組
- BOOSTXL-TUSS4470 — 具有 LDO 的 TUSS4470 直接驅動超音波轉換器評估模組
TUSS4470
- Integrated driver for directly driving transducers and receiver stage with analog output for ultrasound applications
- 86-dB input dynamic range analog front-end
- First stage low noise amplifier adjustable to 10, 12.5, 15 and 20 V/V
- Configurable bandpass filter from 40 KHz to 500 KHz
- Wide-band logarithmic amplifier
- Supported transducer frequencies (controlled by external clock)
- 40 KHz to 1 MHz
- Pre-driver mode: 40 KHz to 440 KHz
- For low-power applications
- Standby mode: 1.7 mA (typical)
- Sleep mode: 220 µA (typical)
- Configurable drive stage:
- Direct drive using internal H-Bridge for transducer excitation
- Pre-driver configuration to use internal H-bridge to drive external Field Effect Transistors (FETs) for higher current drive
- Configurable burst patterns using IO1 and IO2 pins
- Outputs:
- Voltage output of the demodulated echo envelope on VOUT
- Input signal zero crossing comparator output on OUT3 pin
- Programmable VOUT threshold crossing on OUT4 pin
- Serial Peripheral Interface (SPI) for configuration by microcontroller (MCU)
The TUSS4470 is a highly integrated direct drive analog front end for industrial ultrasonic applications. The transducer drive stage is an internal H-bridge that can be configured to drive the transducer in direct-drive mode to achieve maximum voltage across the transducer. The internal H-bridge can also be configured as a pre-driver for external FETs, enabling higher current and voltage drive for larger transducers.
The receive signal path includes a low-noise linear amplifier, a bandpass filter, followed by a logarithmic gain amplifier for input dependent amplification. The logarithmic amplifier allows for high sensitivity for weak echo signals and offers excellent input dynamic range over full range of reflected echoes.
The drivers can be controlled directly through the microcontroller for complete customization of the burst signal, or can be programmed through SPI with a customizable burst length. The TUSS4470 can support a single transducer to send and receive burst signals, or can set up two transducers to split the send and receive functions.
技術文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 8 | 類型 | 標題 | 日期 | ||
|---|---|---|---|---|
| * | Data sheet | TUSS4470 Transformer Drive Ultrasonic Sensor IC With Logarithmic Amplifier datasheet (Rev. A) | PDF | HTML | 2022年 5月 19日 |
| Application note | Ultrasonic Sensing Basics (Rev. D) | PDF | HTML | 2021年 12月 2日 | |
| Application note | Ultrasonic Application Optimization and Usage Guide: TUSS4470 and TDC1000 | PDF | HTML | 2021年 1月 18日 | |
| Technical article | Shrink your solution size with transformer-less ultrasonic ICs | PDF | HTML | 2020年 6月 15日 | |
| User guide | TUSS44x0 EVM for Ultrasonic Sensors User's Guide (Rev. A) | 2020年 4月 2日 | ||
| Application note | TUSS44x0 Software Development Guide | PDF | HTML | 2020年 3月 17日 | |
| Application note | Logarithmic Amplifier for Ultrasonic Sensor Signal Conditioning | 2020年 3月 13日 | ||
| E-book | E-book: An engineer’s guide to industrial robot designs | 2020年 2月 12日 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
開發板
BOOSTXL-TUSS4470 — 具有 LDO 的 TUSS4470 直接驅動超音波轉換器評估模組
TUSS4470 EVM 是 BOOSTXL-TUSS4470 和 MSP-EXP430F5529LP 的集合體，可讓使用者完整評估 TUSS4470 超音波感測器訊號調節器和全橋驅動器。轉換器相容性已擴展到可在 30 至 1000 kHz 之間運作的開放式或封閉式轉換器。轉換器驅動級為內部全橋，可配置為在直接驅動模式下驅動轉換器，以達到轉換器的最大電壓，或可配置為外部 FET 的預驅動器，為大型轉換器實現更高電流和電壓驅動。驅動器可透過 MCU 直接進行控制以完全自訂突衝訊號，或可透過 SPI (...)
使用指南: PDF
Gerber 檔案
Direct-Drive Ultrasonic Proximity Sensing Module Design Files (TUSS4470PSM)
SLDC022.ZIP (4425 KB)
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| WQFN (RTJ) | 20 | Ultra Librarian |
訂購與品質
內含資訊：
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
內含資訊：
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。