SLASF30 January   2022 TAA5212

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics
    6. 6.6  Timing Requirements: I2C Interface
    7. 6.7  Switching Characteristics: I2C Interface
    8. 6.8  Timing Requirements: SPI Interface
    9. 6.9  Switching Characteristics: SPI Interface
    10. 6.10 Timing Requirements: TDM, I2S or LJ Interface
    11. 6.11 Switching Characteristics: TDM, I2S or LJ Interface
    12. 6.12 Timing Requirements: PDM Digital Microphone Interface
    13. 6.13 Switching Characteristics: PDM Digial Microphone Interface
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Hardware Control
      2. 8.3.2 Serial Interfaces
        1. 8.3.2.1 Control Serial Interfaces
        2. 8.3.2.2 Audio Serial Interfaces
          1. 8.3.2.2.1 Time Division Multiplexed Audio (TDM) Interface
          2. 8.3.2.2.2 Inter IC Sound (I2S) Interface
          3. 8.3.2.2.3 Left-Justified (LJ) Interface
        3. 8.3.2.3 Using Multiple Devices With Shared Buses
      3. 8.3.3 Phase-Locked Loop (PLL) and Clock Generation
      4. 8.3.4 Input Channel Configurations
      5. 8.3.5 Reference Voltage
      6. 8.3.6 Programmable Microphone Bias
      7. 8.3.7 Signal-Chain Processing
        1. 8.3.7.1 ADC Signal-Chain
          1. 8.3.7.1.1 Programmable Channel Gain and Digital Volume Control
          2. 8.3.7.1.2 Programmable Channel Gain Calibration
          3. 8.3.7.1.3 Programmable Channel Phase Calibration
          4. 8.3.7.1.4 Programmable Digital High-Pass Filter
          5. 8.3.7.1.5 Programmable Digital Biquad Filters
          6. 8.3.7.1.6 Programmable Channel Summer and Digital Mixer
          7. 8.3.7.1.7 Configurable Digital Decimation Filters
            1. 8.3.7.1.7.1 Linear Phase Filters
              1. 8.3.7.1.7.1.1 Sampling Rate: 16 kHz or 14.7 kHz
              2. 8.3.7.1.7.1.2 Sampling Rate: 24 kHz or 22.05 kHz
              3. 8.3.7.1.7.1.3 Sampling Rate: 32 kHz or 29.4 kHz
              4. 8.3.7.1.7.1.4 Sampling Rate: 48 kHz or 44.1 kHz
              5. 8.3.7.1.7.1.5 Sampling Rate: 96 kHz or 88.2 kHz
      8. 8.3.8 Interrupts, Status, and Digital I/O Pin Multiplexing
      9. 8.3.9 Programmable Channel Phase Calibration
    4. 8.4 Device Functional Modes
    5. 8.5 Register Maps
      1. 8.5.1 VEGA Registers
      2. 8.5.2 TAA5212 Registers
      3. 8.5.3 TAA5212 Registers
    6. 8.6 Feature Description
    7. 8.7 Device Functional Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Application
      2. 9.2.2 Design Requirements
      3. 9.2.3 Detailed Design Procedure
      4. 9.2.4 Application Performance Plots
      5. 9.2.5 What to Do and What Not to Do
  11. 10Power Supply Recommendations
  12. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  13. 12Device and Documentation Support
    1. 12.1 Documentation Support
      1. 12.1.1 Related Documentation
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 Support Resources
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  14. 13Mechanical, Packaging, and Orderable Information
    1. 13.1 Tape and Reel Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.3.9 Programmable Channel Phase Calibration

In addition to the gain calibration, the phase delay in each channel can be finely calibrated or adjusted in steps of one modulator clock cycle for a cycle range of 0 to 255 for the phase error. The modulator clock, the same clock used for ADC_MOD_CLK, is 6.144 MHz (the output data sample rate is multiples or submultiples of 48 kHz) or 5.6448 MHz (the output data sample rate is multiples or submultiples of 44.1 kHz) irrespective of the analog microphone or digital microphone use case. This feature is very useful for many applications that must match the phase with fine resolution between each channel, including any phase mismatch across channels resulting from external components or microphones. Table 8-26 shows the available programmable options for channel phase calibration.

Table 8-26 Channel Phase Calibration Programmable Settings
P0_R64_D[7:0] : CH1_PCAL[7:0]CHANNEL PHASE CALIBRATION SETTING FOR INPUT CHANNEL 1
0000 0000 = 0d (default)Input channel 1 phase calibration with no delay
0000 0001 = 1dInput channel 1 phase calibration delay is set to one cycle of the modulator clock
0000 0010 = 2dInput channel 1 phase calibration delay is set to two cycles of the modulator clock
……
1111 1110 = 254dInput channel 1 phase calibration delay is set to 254 cycles of the modulator clock
1111 1111 = 255dInput channel 1 phase calibration delay is set to 255 cycles of the modulator clock

Similarly, the channel phase calibration setting for input channel 2 to channel 8 can be configured using the CH2_PCAL (P0_R69) to CH8_PCAL (P0_R99) register bits, respectively.

The phase calibration feature must not be used when the analog input and PDM input are used together for simultaneous conversion.