SWCS138E June   2017  – December 2022 TPS650864

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Electrical Characteristics: Total Current Consumption
    6. 7.6  Electrical Characteristics: Reference and Monitoring System
    7. 7.7  Electrical Characteristics: Buck Controllers
    8. 7.8  Electrical Characteristics: Synchronous Buck Converters
    9. 7.9  Electrical Characteristics: LDOs
    10. 7.10 Electrical Characteristics: Load Switches
    11. 7.11 Digital Signals: I2C Interface
    12. 7.12 Digital Input Signals (CTLx)
    13. 7.13 Digital Output Signals (IRQB, GPOx)
    14. 7.14 Timing Requirements
    15. 7.15 Switching Characteristics
    16. 7.16 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1  Overview
    2. 8.2  Functional Block Diagram
    3. 8.3  TPS6508640 Design and Settings
      1. 8.3.1 TPS6508640 OTP Summary
    4. 8.4  TPS65086401 Design and Settings
      1. 8.4.1 TPS65086401 OTP Summary
      2.      31
    5. 8.5  TPS6508641 Design and Settings
      1. 8.5.1 TPS6508641 OTP Summary
    6. 8.6  TPS65086470 Design and Settings
      1. 8.6.1 TPS65086470 OTP Summary
    7. 8.7  SMPS Voltage Regulators
      1. 8.7.1 Controller Overview
      2. 8.7.2 Converter Overview
      3. 8.7.3 DVS
      4. 8.7.4 Decay
      5. 8.7.5 Current Limit
    8. 8.8  LDOs and Load Switches
      1. 8.8.1 VTT LDO
      2. 8.8.2 LDOA1–LDOA3
      3. 8.8.3 Load Switches
    9. 8.9  Power Goods (PGOOD or PG) and GPOs
    10. 8.10 Power Sequencing and VR Control
      1. 8.10.1 CTLx Sequencing
      2. 8.10.2 PG Sequencing
      3. 8.10.3 Enable Delay
      4. 8.10.4 Power-Up Sequence
      5. 8.10.5 Power-Down Sequence
      6. 8.10.6 Sleep State Entry and Exit
      7. 8.10.7 Emergency Shutdown
    11. 8.11 Device Functional Modes
      1. 8.11.1 Off Mode
      2. 8.11.2 Standby Mode
      3. 8.11.3 Active Mode
    12. 8.12 I2C Interface
      1. 8.12.1 F/S-Mode Protocol
    13. 8.13 Register Maps
      1. 8.13.1  Register Map Summary
      2. 8.13.2  DEVICEID1: 1st PMIC Device and Revision ID Register (offset = 00h) [reset = X]
      3. 8.13.3  DEVICEID2: 2nd PMIC Device and Revision ID Register (offset = 01h) [reset = X]
      4. 8.13.4  IRQ: PMIC Interrupt Register (offset = 02h) [reset = 0000 0000]
      5. 8.13.5  IRQ_MASK: PMIC Interrupt Mask Register (offset = 03h) [reset = 1111 1111]
      6. 8.13.6  PMICSTAT: PMIC Status Register (offset = 04h) [reset = 0000 0000]
      7. 8.13.7  SHUTDNSRC: PMIC Shut-Down Event Register (offset = 05h) [reset = 0000 0000]
      8. 8.13.8  BUCK1CTRL: BUCK1 Control Register (offset = 20h) [reset = X]
      9. 8.13.9  BUCK2CTRL: BUCK2 Control Register (offset = 21h) [reset = X]
      10. 8.13.10 BUCK3DECAY: BUCK3 Decay Control Register (offset = 22h) [reset = X]
      11. 8.13.11 BUCK3VID: BUCK3 VID Register (offset = 23h) [reset = X]
      12. 8.13.12 BUCK3SLPCTRL: BUCK3 Sleep Control VID Register (offset = 24h) [reset = X]
      13. 8.13.13 BUCK4CTRL: BUCK4 Control Register (offset = 25h) [reset = X]
      14. 8.13.14 BUCK5CTRL: BUCK5 Control Register (offset = 26h) [reset = X]
      15. 8.13.15 BUCK6CTRL: BUCK6 Control Register (offset = 27h) [reset = X]
      16. 8.13.16 LDOA2CTRL: LDOA2 Control Register (offset = 28h) [reset = X]
      17. 8.13.17 LDOA3CTRL: LDOA3 Control Register (offset = 29h) [reset = X]
      18. 8.13.18 DISCHCTRL1: 1st Discharge Control Register (offset = 40h) [reset = X]
      19. 8.13.19 DISCHCTRL2: 2nd Discharge Control Register (offset = 41h) [reset = X]
      20. 8.13.20 DISCHCTRL3: 3rd Discharge Control Register (offset = 42h) [reset = X]
      21. 8.13.21 PG_DELAY1: 1st Power Good Delay Register (offset = 43h) [reset = X]
      22. 8.13.22 FORCESHUTDN: Force Emergency Shutdown Control Register (offset = 91h) [reset = 0000 0000]
      23. 8.13.23 BUCK1SLPCTRL: BUCK1 Sleep Control Register (offset = 92h) [reset = X]
      24. 8.13.24 BUCK2SLPCTRL: BUCK2 Sleep Control Register (offset = 93h) [reset = X]
      25. 8.13.25 BUCK4VID: BUCK4 VID Register (offset = 94h) [reset = X]
      26. 8.13.26 BUCK4SLPVID: BUCK4 Sleep VID Register (offset = 95h) [reset = X]
      27. 8.13.27 BUCK5VID: BUCK5 VID Register (offset = 96h) [reset = X]
      28. 8.13.28 BUCK5SLPVID: BUCK5 Sleep VID Register (offset = 97h) [reset = X]
      29. 8.13.29 BUCK6VID: BUCK6 VID Register (offset = 98h) [reset = X]
      30. 8.13.30 BUCK6SLPVID: BUCK6 Sleep VID Register (offset = 99h) [reset = X]
      31. 8.13.31 LDOA2VID: LDOA2 VID Register (offset = 9Ah) [reset = X]
      32. 8.13.32 LDOA3VID: LDOA3 VID Register (offset = 9Bh) [reset = X]
      33. 8.13.33 BUCK123CTRL: BUCK1-3 Control Register (offset = 9Ch) [reset = X]
      34. 8.13.34 PG_DELAY2: 2nd Power Good Delay Register (offset = 9Dh) [reset = X]
      35. 8.13.35 SWVTT_DIS: SWVTT Disable Register (offset = 9Fh) [reset = X]
      36. 8.13.36 I2C_RAIL_EN1: 1st VR Pin Enable Override Register (offset = A0h) [reset = X]
      37. 8.13.37 I2C_RAIL_EN2/GPOCTRL: 2nd VR Pin Enable Override and GPO Control Register (offset = A1h) [reset = X]
      38. 8.13.38 PWR_FAULT_MASK1: 1st VR Power Fault Mask Register (offset = A2h) [reset = X]
      39. 8.13.39 PWR_FAULT_MASK2: 2nd VR Power Fault Mask Register (offset = A3h) [reset = X]
      40. 8.13.40 GPO1PG_CTRL1: 1st GPO1 PG Control Register (offset = A4h) [reset = X]
      41. 8.13.41 GPO1PG_CTRL2: 2nd GPO1 PG Control Register (offset = A5h) [reset = X]
      42. 8.13.42 GPO4PG_CTRL1: 1st GPO4 PG Control Register (offset = A6h) [reset = X]
      43. 8.13.43 GPO4PG_CTRL2: 2nd GPO4 PG Control Register (offset = A7h) [reset = X]
      44. 8.13.44 GPO2PG_CTRL1: 1st GPO2 PG Control Register (offset = A8h) [reset = X]
      45. 8.13.45 GPO2PG_CTRL2: 2nd GPO2 PG Control Register (offset = A9h) [reset = X]
      46. 8.13.46 GPO3PG_CTRL1: 1st GPO3 PG Control Register (offset = AAh) [reset = X]
      47. 8.13.47 GPO3PG_CTRL2: 2nd GPO3 PG Control Register (offset = ABh) [reset = X]
      48. 8.13.48 MISCSYSPG Register (offset = ACh) [reset = X]
        1. 8.13.48.1 VTT_DISCH_CTRL Register (offset = ADh) [reset = X]
      49. 8.13.49 LDOA1_SWB2_CTRL: LDOA1 and SWB2 Control Register (offset = AEh) [reset = X]
      50. 8.13.50 PG_STATUS1: 1st Power Good Status Register (offset = B0h) [reset = 0000 0000]
      51. 8.13.51 PG_STATUS2: 2nd Power Good Status Register (offset = B1h) [reset = 0000 0000]
      52. 8.13.52 PWR_FAULT_STATUS1: 1st Power Fault Status Register (offset = B2h) [reset = 0000 0000]
      53. 8.13.53 PWR_FAULT_STATUS2: 2nd Power Fault Status Register (offset = B3h) [reset = 0000 0000]
      54. 8.13.54 TEMPCRIT: Temperature Fault Status Register (offset = B4h) [reset = 0000 0000]
      55. 8.13.55 TEMPHOT: Temperature Hot Status Register (offset = B5h) [reset = 0000 0000]
      56. 8.13.56 OC_STATUS: Overcurrent Fault Status Register (offset = B6h) [reset = 0000 0000]
  9. 9 Applications, Implementation, and Layout
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Controller Design Procedure
          1. 9.2.2.1.1 Selecting the Inductor
          2. 9.2.2.1.2 Selecting the Output Capacitors
          3. 9.2.2.1.3 Selecting the FETs
          4. 9.2.2.1.4 Bootstrap Capacitor
          5. 9.2.2.1.5 Setting the Current Limit
          6. 9.2.2.1.6 Selecting the Input Capacitors
        2. 9.2.2.2 Converter Design Procedure
          1. 9.2.2.2.1 Selecting the Inductor
          2. 9.2.2.2.2 Selecting the Output Capacitors
          3. 9.2.2.2.3 Selecting the Input Capacitors
        3. 9.2.2.3 LDO Design Procedure
      3. 9.2.3 Application Curves
      4. 9.2.4 Layout
        1. 9.2.4.1 Layout Guidelines
        2. 9.2.4.2 Layout Example
      5. 9.2.5 VIN 5-V Application
        1. 9.2.5.1 Design Requirements
        2. 9.2.5.2 Design Procedure
        3. 9.2.5.3 Application Curves
    3. 9.3 Power Supply Coupling and Bulk Capacitors
    4. 9.4 Do's and Don'ts
  10. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 Third-Party Products Disclaimer
      2. 10.1.2 Development Support
    2. 10.2 Documentation Support
      1. 10.2.1 Related Documentation
    3. 10.3 Receiving Notification of Documentation Updates
    4. 10.4 Support Resources
    5. 10.5 Trademarks
    6. 10.6 Electrostatic Discharge Caution
    7. 10.7 Glossary
  11. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.1 Overview

The TPS650864 power-management integrated circuit (PMIC) provides a highly flexible and configurable power solution that can power a wide array of processors along with DDR3/DDR4 memory and other peripherals. Integrated in the PMIC are three step-down controllers (BUCK1, BUCK2, and BUCK6), three step-down converters (BUCK3, BUCK4, and BUCK5), a sink or source LDO (VTT LDO), three low-voltage VIN LDOs (LDOA1–LDOA3), and three load switches (SWA1, SWB1, and SWB2). With on-chip one-time programmable (OTP) memory, configuration of each rail for default output value, power-up sequence, fault handling, and Power Good mapping into a GPO pin are all conveniently flexible. All VRs have a built-in discharge resistor, and the value can be changed using the DISCHCNT1–DISCHCNT3 and LDOA1_SWB2_CTRL registers. When enabling a VR, the PMIC automatically disconnects the discharge resistor for that rail without any I2C command. Table 8-1 lists the key characteristics of the voltage rails.

Table 8-1 Summary of Voltage Regulators
RAILTYPEINPUT VOLTAGE (V)OUTPUT VOLTAGE RANGE (V)CURRENT (mA)
MINMAXMINTYPMAX
BUCK1Step-down controller4.5210.41See Section 53.575scalable
BUCK2Step-down controller4.5210.41See Section 53.575scalable
BUCK3Step-down converter35.50.41See Section 53.5753000
BUCK4Step-down Converter35.50.41See Section 53.5753000
BUCK5Step-down converter35.50.41See Section 53.5753000
BUCK6Step-down controller4.5210.41See Section 53.575scalable
LDOA1LDO4.55.51.35See Section 53.3200(1)
LDOA2LDO1.621.980.7See Section 51.5600
LDOA3LDO1.621.980.7See Section 51.5600
SWA1Load switch0.53.3300
SWB1/SWB2Load switch0.53.3400
VTTSink and source LDO1.11.8FBVOUT6 / 2See Section 5
(1) When powered from a 5-V supply through the DRV5V_2_A1 pin. Otherwise, max current is limited by max IOUT of LDO5.