JAJSSD2A October   2023  – December 2023 BQ25638

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 概要 (続き)
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Power-On-Reset (POR)
      2. 7.3.2  Device Power Up from Battery
      3. 7.3.3  Device Power Up from Input Source
        1. 7.3.3.1 REGN LDO Power Up
        2. 7.3.3.2 Poor Source Qualification
        3. 7.3.3.3 Input Voltage Limit Threshold Setting (VINDPM Threshold)
        4. 7.3.3.4 Converter Power-Up
        5. 7.3.3.5 Input Current Optimizer (ICO)
        6. 7.3.3.6 Switching Frequency and Dithering Feature
      4. 7.3.4  Power Path Management
        1. 7.3.4.1 Narrow VDC Architecture
        2. 7.3.4.2 Dynamic Power Management
          1. 7.3.4.2.1 Input Current Limit on ILIM Pin
        3. 7.3.4.3 High Impedance (HIZ) Mode
      5. 7.3.5  Battery Charging Management
        1. 7.3.5.1 Autonomous Charging Cycle
        2. 7.3.5.2 Battery Charging Profile
        3. 7.3.5.3 Charging Termination
        4. 7.3.5.4 Thermistor Qualification
          1. 7.3.5.4.1 Advanced Temperature Profile in Charge Mode
          2. 7.3.5.4.2 TS Pin Thermistor Configuration
          3. 7.3.5.4.3 Cold/Hot Temperature Window in OTG Mode
          4. 7.3.5.4.4 JEITA Charge Rate Scaling
          5. 7.3.5.4.5 TS_BIAS Pin
        5. 7.3.5.5 Charging Safety Timers
      6. 7.3.6  USB On-The-Go (OTG)
        1. 7.3.6.1 Boost OTG Mode
      7. 7.3.7  Integrated 12-bit ADC for Monitoring
      8. 7.3.8  Status Outputs (INT , PG , STAT)
        1. 7.3.8.1 PG Pin Power Good Indicator
        2. 7.3.8.2 Charging Status Indicator (STAT)
        3. 7.3.8.3 Interrupt to Host (INT)
      9. 7.3.9  BATFET Control
        1. 7.3.9.1 Shutdown Mode
        2. 7.3.9.2 Ultra-Low Power Mode
        3. 7.3.9.3 System Power Reset
      10. 7.3.10 Protections
        1. 7.3.10.1 Voltage and Current Monitoring in Battery Only and HIZ Modes
          1. 7.3.10.1.1 Battery Overcurrent Protection
          2. 7.3.10.1.2 Battery Undervoltage Lockout
        2. 7.3.10.2 Voltage and Current Monitoring in Forward Mode
          1. 7.3.10.2.1 Input Overvoltage
          2. 7.3.10.2.2 System Overvoltage Protection (SYSOVP)
          3. 7.3.10.2.3 Forward Converter Cycle-by-Cycle Current Limit
          4. 7.3.10.2.4 System Short
          5. 7.3.10.2.5 Battery Overvoltage Protection (BATOVP)
          6. 7.3.10.2.6 Sleep and Poor Source Comparators
        3. 7.3.10.3 Voltage and Current Monitoring in Reverse Mode
          1. 7.3.10.3.1 Boost Mode Overvoltage Protection
          2. 7.3.10.3.2 Boost Mode Duty Cycle Protection
          3. 7.3.10.3.3 Boost Mode PMID Undervoltage Protection
          4. 7.3.10.3.4 Boost Mode Battery Undervoltage
          5. 7.3.10.3.5 Boost Converter Cycle-by-Cycle Current Limit
          6. 7.3.10.3.6 Boost Mode SYS Short
        4. 7.3.10.4 Thermal Regulation and Thermal Shutdown
          1. 7.3.10.4.1 Thermal Protection in Buck Mode
          2. 7.3.10.4.2 Thermal Protection in Boost Mode
          3. 7.3.10.4.3 Thermal Protection in Battery-only Mode
    4. 7.4 Device Functional Modes
      1. 7.4.1 Host Mode and Default Mode
      2. 7.4.2 Register Bit Reset
    5. 7.5 Programming
      1. 7.5.1 Serial Interface
        1. 7.5.1.1 Data Validity
        2. 7.5.1.2 START and STOP Conditions
        3. 7.5.1.3 Byte Format
        4. 7.5.1.4 Acknowledge (ACK) and Not Acknowledge (NACK)
        5. 7.5.1.5 Target Address and Data Direction Bit
        6. 7.5.1.6 Single Write and Read
        7. 7.5.1.7 Multi-Write and Multi-Read
    6. 7.6 BQ25638 Registers
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Inductor Selection
        2. 8.2.2.2 Input Capacitor
        3. 8.2.2.3 Output Capacitor
      3. 8.2.3 Application Curves
  10. 9 Power Supply Recommendations
  11. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 サード・パーティ製品に関する免責事項
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 ドキュメントの更新通知を受け取る方法
    4. 11.4 サポート・リソース
    5. 11.5 Trademarks
    6. 11.6 静電気放電に関する注意事項
    7. 11.7 用語集
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ（パッケージ｜ピン）
  • YBG|30
サーマルパッド・メカニカル・データ
7.3.4.2.1 Input Current Limit on ILIM Pin

For safe operation, the device has an additional hardware pin on ILIM to limit the maximum input current on ILIM pin. The maximum input current is set by a resistor from ILIM pin to GND as:

Equation 1. I I N R E G = K I L I M R I L I M

The actual input current is limited to the lower of the two values set by ILIM pin and IINDPM register bits. The device regulates ILIM pin at 0.8 V. If ILIM voltage exceeds 0.8 V, the device enters input current regulation (refer to Dynamic Power Management).

The ILIM pin can also be used to monitor input current. The input current is proportional to the voltage on ILIM pin and can be calculated by:

Equation 2. I I N = K I L I M × V I L I M R I L I M × 0.8

The ILIM pin function is disabled when EN_EXTILIM bit is set to 0. When the pin is disabled, both input current limit and monitoring functions are not available.

An RC filter in parallel with RILIM is required when input current setting on ILIM pin is either:

  1. Below 400 mA or
  2. Above 2 A with 2.2-μH inductor

The value of the RC filter is 1.2 kΩ and 330 nF, respectively.