JAJSGL3D January   2014  – October 2021 TCA9539-Q1

PRODUCTION DATA  

  1. 特長
  2. アプリケーション
  3. 概要
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Interface Timing Requirements
    7. 6.7 RESET Timing Requirements
    8. 6.8 Switching Characteristics
    9. 6.9 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 I/O Port
      2. 8.3.2 RESET Input
      3. 8.3.3 Interrupt ( INT) Output
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power-On Reset
    5. 8.5 Programming
      1. 8.5.1 I2C Interface
    6. 8.6 Register Maps
      1. 8.6.1 Device Address
      2. 8.6.2 Control Register And Command Byte
      3. 8.6.3 Register Descriptions
        1. 8.6.3.1 Bus Transactions
          1. 8.6.3.1.1 Writes
          2. 8.6.3.1.2 Reads
  9. Power Supply Recommendations
    1. 9.1 Power-On Reset Requirements
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 サポート・リソース
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary

パッケージ・オプション

メカニカル・データ(パッケージ|ピン)
サーマルパッド・メカニカル・データ
発注情報

Electrical Characteristics

over recommended operating free-air temperature range (unless otherwise noted)
PARAMETERTEST CONDITIONSVCCMINTYP (1)MAXUNIT
VIKInput diode clamp voltageII = –18 mA1.65 V to 3.6 V–1.2V
VPORRPower-on reset voltage, VCC risingVI = VCC or GND1.65 V to 3.6 V1.21.5V
VPORFPower-on reset voltage, VCC fallingVI = VCC or GND1.65 V to 3.6 V0.751V
VOHP-port high-level output voltage (2)IOH = –8 mA1.65 V1.2V
2.3 V1.8
3 V2.6
3.6 V3.3
IOH = –10 mA1.65 V1
2.3 V1.7
3 V2.5
3.6 V3.2
IOLSDAVOL = 0.4 V1.65 V to 3.6 V3mA
P port (3)VOL = 0.5 V8
VOL = 0.7 V10
INTVOL = 0.4 V3
IISCL, SDAVI = VCC or GND1.65 V to 3.6 V±1µA
A0, A1, RESET±1
IIHP portVI = VCC1.65 V to 3.6 V1µA
IILP portVI = GND1.65 V to 3.6 V–1µA
ICCOperating modeVI = VCC or GND, IO = 0,
I/O = inputs, fSCL = 400 kHz, no load
3.6 V1030µA
2.7 V519
1.95 V411
Standby modeIO = 0, I/O = inputs,
fSCL = 0 kHz, no load
VI = VCC3.6 V1.15
2.7 V14.5
1.95 V0.43.5
VI = GND3.6 V1.113
2.7 V19.5
1.95 V0.46.5
CiSCLVI = VCC or GND1.65 V to 3.6 V38pF
CioSDAVIO = VCC or GND1.65 V to 3.6 V39.5pF
P port3.79.5
All typical values are at nominal supply voltage (1.8 V, 2.5 V, or 3.3 V, VCC) and TA = 25°C.
Each I/O must be externally limited to the maximum allowed IOL, and each octal (P07–P00 and P17–P10) must be limited to a maximum current of 100 mA, for a device total of 200 mA at Tj ≤ 85°C. See the Section 6.3 table for more information.
The total current sourced by all I/Os must be limited to 160 mA (80 mA for P07–P00 and 80 mA for P17–P10) for Tj ≤ 85°C. See the Section 6.3 table for more information.